AcBoard
AudioCodes LTDAudioCodes Proprietary MIB
Contains The managed objects of AudioCodes systems.
Through this MIB, the User can set up the board configuration parameters, reset the board,
and monitor the board's operational robustness and quality of service during run-time.
This MIB has the following Groups:
boardConfiguration
boardInformation
channelConfiguration
channelStatus
notifications
reset
boardConfiguration:
When The user Get Parameter from most of sub-groups in boardConfiguration group,
he gets the value that should be burned to the board after the next Remote Reset.
He can Set new values to many parameters, and these values will burned to the board after the next remote Reset
In the sub-group mGCPDefaultChannelSettings the parameters are the actual parameters,
that will take place when opening channel. (Reset is not needed for that sub-group).
BoardInformation:
Contains Read-only parameters like: board name, serial number, number of channels, software version.
ChannelConfiguration:
Read-only Parameters to see the configuratin of each channel: voice settings, fax settings, etc.
ChannelStatus:
Read-only parameters about the status of channel, like: Is the channle active, is it in Silence Period,
is it in Fax mode, ON/Off hook, etc.
This group contains also counters: packets to DSP, errors, lost packets, underruns, etc.
Notifications:
In this version, the notification we have are: acEvBoardStarted, and acEvResetingBoard.
The board should send these notifications to its manager
that the user defined in INI file with the parameter: NMPManagerIP = (IP address).
Reset:
To remote reset the board, the user should set an integer value to the parameter remoteReset.
Then he should get the trap acEvResettingBoard.
Note: Before Reset, The current boardConfiguration parameters will be burned to the board.
The user should not use INI file, if he wants these parameters to take place.
To set the default values, the user should set an integer value to the parameter acSetDefaults.snmptranslate -m AcBoard -Tpsnmpwalk -v2c -c <community> -m AcBoard <host> 1.3.6.1.4.1.5003.9.10.1Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DateAndTime, DisplayString, PhysAddress, TAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| NaudioCodes | 1.3.6.1.4.1.5003 | ||||||||||||||||
| NacRegistrations | 1.3.6.1.4.1.5003.7 | ||||||||||||||||
| NacGeneric | 1.3.6.1.4.1.5003.8 | ||||||||||||||||
| NacProducts | 1.3.6.1.4.1.5003.9 | ||||||||||||||||
| NacBoardMibs | 1.3.6.1.4.1.5003.9.10 | ||||||||||||||||
| IacBoard | 1.3.6.1.4.1.5003.9.10.1 | ||||||||||||||||
identity AudioCodes Proprietary MIB
Contains The managed objects of AudioCodes systems.
Through this MIB, the User can set up the board configuration parameters, reset the board,
and monitor the board's operational robustness and quality of service during run-time.
This MIB has the following Groups:
boardConfiguration
boardInformation
channelConfiguration
channelStatus
notifications
reset
boardConfiguration:
When The user Get Parameter from most of sub-groups in boardConfiguration group,
he gets the value that should be burned to the board after the next Remote Reset.
He can Set new values to many parameters, and these values will burned to the board after the next remote Reset
In the sub-group mGCPDefaultChannelSettings the parameters are the actual parameters,
that will take place when opening channel. (Reset is not needed for that sub-group).
BoardInformation:
Contains Read-only parameters like: board name, serial number, number of channels, software version.
ChannelConfiguration:
Read-only Parameters to see the configuratin of each channel: voice settings, fax settings, etc.
ChannelStatus:
Read-only parameters about the status of channel, like: Is the channle active, is it in Silence Period,
is it in Fax mode, ON/Off hook, etc.
This group contains also counters: packets to DSP, errors, lost packets, underruns, etc.
Notifications:
In this version, the notification we have are: acEvBoardStarted, and acEvResetingBoard.
The board should send these notifications to its manager
that the user defined in INI file with the parameter: NMPManagerIP = (IP address).
Reset:
To remote reset the board, the user should set an integer value to the parameter remoteReset.
Then he should get the trap acEvResettingBoard.
Note: Before Reset, The current boardConfiguration parameters will be burned to the board.
The user should not use INI file, if he wants these parameters to take place.
To set the default values, the user should set an integer value to the parameter acSetDefaults. | |||||||||||||||||
| NboardConfiguration | 1.3.6.1.4.1.5003.9.10.1.1 | ||||||||||||||||
| NboardTDMBusSettings | 1.3.6.1.4.1.5003.9.10.1.1.1 | ||||||||||||||||
| SpCMLawSelect | 1.3.6.1.4.1.5003.9.10.1.1.1.1 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Selects the type of PCM companding law in input/output TDM bus (TDM bus is defined using the TDMBusType parameter).
| |||||||||||||||||
| StDMBusClockSource | 1.3.6.1.4.1.5003.9.10.1.1.1.2 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Selects the clock source on which the board synchronizes
| |||||||||||||||||
| StDMBusEnableFallBack | 1.3.6.1.4.1.5003.9.10.1.1.1.3 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Enable/Disable clock fallback. The Fall Back clock is determined by BSPTDMBusFallbackClock
| |||||||||||||||||
| StDMBusLocalReference | 1.3.6.1.4.1.5003.9.10.1.1.1.4 | INTEGER (0..27) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..27) · read-write · obsolete When ClockSource is set to acH110BusClockSource_Network this parameter selects the TrunkID to be used as the clock synchronization source of the board. When using H.110/H.100 bus this parameter also selects the trunk which is used as the clock source for the NETREF clock generation (in this case ClockSource might not be set to acH110BusClockSource_Network). | |||||||||||||||||
| SidlePCMPattern | 1.3.6.1.4.1.5003.9.10.1.1.1.5 | INTEGER (0..255) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..255) · read-write · obsolete PCM Pattern applied to E1/T1 timeslot (B-channel) when channel is idle. | |||||||||||||||||
| SidleABCD | 1.3.6.1.4.1.5003.9.10.1.1.1.6 | INTEGER (0..15) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..15) · read-write · obsolete ABCD (CAS) Pattern to be applied to CAS signaling bus before changed by the user or PSTN protocol. This is only relevant when using PSTN interface with CAS protocols. | |||||||||||||||||
| StDMBusMasterSlaveSelection | 1.3.6.1.4.1.5003.9.10.1.1.1.7 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Set SC/MVIP/H.110 to either: Master mode (the board is the clock source for the TDM bus) or Slave mode (some other board in the system must supply the clock to the TDM bus).
| |||||||||||||||||
| StDMBusNetRefSpeed | 1.3.6.1.4.1.5003.9.10.1.1.1.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Determine the NetRef frequency (for both generation and synchronization).
| |||||||||||||||||
| StDMBusOutputStartingChannel | 1.3.6.1.4.1.5003.9.10.1.1.1.9 | INTEGER (0..127) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..127) · read-write · obsolete Defines the outgoing TDM Timeslot of the first channel (ChannelId=0). The remaining channels are organized sequentially. | |||||||||||||||||
| SboardTDMBusOutputPort | 1.3.6.1.4.1.5003.9.10.1.1.1.10 | INTEGER (0..31) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..31) · read-write · obsolete Defines the SC/MVIP/H.100/H.110 port to be used for board's channel #0. All other channels then occupy the next timeslots sequentially | |||||||||||||||||
| StDMBusSpeed | 1.3.6.1.4.1.5003.9.10.1.1.1.11 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Selects the TDM Bus Speed. Speed is set according to the Bus Type. The following are allowed speeds for each bus type: SC = 0/2/3 H.110/H.100 = 3 MVIP = 0
| |||||||||||||||||
| StDMBusType | 1.3.6.1.4.1.5003.9.10.1.1.1.12 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Selects the TDM bus interface to be used (only one TDM bus interface can be enabled at one time although more than one can physically exist on the board).
| |||||||||||||||||
| SacOverrideDefaultIdlePCMPattern | 1.3.6.1.4.1.5003.9.10.1.1.1.13 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Override Default Idle PCM Pattern. 0 - use defaults (0xff-Mulaw, 0x55-Alaw) 1 - use IdlePCMPattern.
| |||||||||||||||||
| SacOverrideDefaultIdleABCDPattern | 1.3.6.1.4.1.5003.9.10.1.1.1.14 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Description: Override Default Idle ABCD Pattern. 0 - use defaults (0xf) 1 - use IdleABCDPattern.
| |||||||||||||||||
| NnetworkSettings | 1.3.6.1.4.1.5003.9.10.1.1.2 | ||||||||||||||||
| SbaseUDPPort | 1.3.6.1.4.1.5003.9.10.1.1.2.1 | INTEGER (0..64000) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..64000) · read-write · obsolete Lower boundary of UDP ports to be used by the board. The upper boundary is BoardBaseUDPPort+10*(Number of Channels). Must be a multiple of 10. | |||||||||||||||||
| SdefaultGatewayAddr | 1.3.6.1.4.1.5003.9.10.1.1.2.2 | IpAddress | RO | obsolete | |||||||||||||
scalar · IpAddress · read-only · obsolete Default Gateway Address. Board's Default Gateway IP address. (in host byte order e.g. 192.10.1.255 = 0xc00a01ff). | |||||||||||||||||
| SboardIPAddr | 1.3.6.1.4.1.5003.9.10.1.1.2.3 | IpAddress | RO | obsolete | |||||||||||||
scalar · IpAddress · read-only · obsolete Board IP Address. in host byte order e.g. 192.10.1.2 = 0xc00a0102). Users should set the subnet mask to a valid value per the IP address. | |||||||||||||||||
| SboardSubNetAddr | 1.3.6.1.4.1.5003.9.10.1.1.2.4 | IpAddress | RO | obsolete | |||||||||||||
scalar · IpAddress · read-only · obsolete Board SubNet Address. (in host byte order e.g. 255.255.255.0 = 0xffffff00). default =255.255.255.0. | |||||||||||||||||
| SacSyslogServerIP | 1.3.6.1.4.1.5003.9.10.1.1.2.5 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete IP address in dotted format notation, e.g., 192.10.1.255 | |||||||||||||||||
| SacMGControlProtocolType | 1.3.6.1.4.1.5003.9.10.1.1.2.6 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete This parameter defines the control protocol type 0 = none, 1 = MGCP, 2 = MEGACO, 4 = H323, 8 = SIP
| |||||||||||||||||
| SacSNMPManagerIP | 1.3.6.1.4.1.5003.9.10.1.1.2.7 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete SNMP manager server IP address | |||||||||||||||||
| SacDisableWEBConfig | 1.3.6.1.4.1.5003.9.10.1.1.2.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Enables or disables Web Configuration 0-Read & Write mode(default) 1-Read Only mode
| |||||||||||||||||
| SacEnableSyslog | 1.3.6.1.4.1.5003.9.10.1.1.2.9 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Enable SysLog protocol log.
| |||||||||||||||||
| SacContrlProtocolTransportType | 1.3.6.1.4.1.5003.9.10.1.1.2.10 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Defines the transport type for the control: 0 - UDP, 1 - TCP (SCTP on road map).
| |||||||||||||||||
| SacCPControlDiffServ | 1.3.6.1.4.1.5003.9.10.1.1.2.11 | INTEGER (0..63) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..63) · read-write · obsolete Defines the value of the 'DiffServ' field in the IP header for the control session. | |||||||||||||||||
| NsnmpManagers | 1.3.6.1.4.1.5003.9.10.1.1.2.21 | ||||||||||||||||
| TsnmpManagersTable | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Snmp Managers Table | |||||||||||||||||
| RsnmpManagersEntry | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CsnmpManagerIndex | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.1 | INTEGER (0..2) | RO | obsolete | |||||||||||||
column · INTEGER (0..2) · read-only · obsolete Snmp Manager Index | |||||||||||||||||
| CsnmpManagerIsUsed | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.2 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Enable the SNMP Manager to recieve traps.
| |||||||||||||||||
| CsnmpManagerIp | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.3 | IpAddress | RW | obsolete | |||||||||||||
column · IpAddress · read-write · obsolete IP address of default SNMP manager in dotted notation format: xxx.xxx.xxx.xxx. SNMP traps are sent to this manager. | |||||||||||||||||
| CsnmpManagerTrapPort | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.4 | INTEGER (0..65535) | RW | obsolete | |||||||||||||
column · INTEGER (0..65535) · read-write · obsolete Sets the trap ports to be used by the different managers. | |||||||||||||||||
| CsnmpManagerTrapSendingEnable | 1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.5 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Enable the SNMP Manager to recieve traps.
| |||||||||||||||||
| NacNTPSettings | 1.3.6.1.4.1.5003.9.10.1.1.2.22 | ||||||||||||||||
| SacNTPServerIPAddress | 1.3.6.1.4.1.5003.9.10.1.1.2.22.1 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete NTP Server IP address. | |||||||||||||||||
| SacNTPUtcOffset | 1.3.6.1.4.1.5003.9.10.1.1.2.22.2 | INTEGER (-43200..43200) | RW | deprecated | |||||||||||||
scalar · INTEGER (-43200..43200) · read-write · deprecated NTP time to offset in seconds. Default is 0. Range - Between -43200 ot 43200 seconds. | |||||||||||||||||
| SacNTPUpdateInterval | 1.3.6.1.4.1.5003.9.10.1.1.2.22.3 | INTEGER (0..2147483647) | RW | deprecated | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · deprecated NTPupdate interval in seconds. Default is 86400 (24 hours). Not recommended to be set beyond one month (2592000 sec). | |||||||||||||||||
| NacWEBAccess | 1.3.6.1.4.1.5003.9.10.1.1.2.23 | ||||||||||||||||
| TacWEBAccessTable | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1 | NA | obsolete | ||||||||||||||
| RacWEBAccessEntry | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CacWEBAccessRowStatus | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.1 | INTEGER (1) | RW | obsolete | |||||||||||||
column · INTEGER (1) · read-write · obsolete WEB Access row-status | |||||||||||||||||
| CacWEBAccessAction | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.2 | INTEGER (0) | RW | obsolete | |||||||||||||
column · INTEGER (0) · read-write · obsolete WEB Access action | |||||||||||||||||
| CacWEBAccessActionResult | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.3 | INTEGER (0) | RO | obsolete | |||||||||||||
column · INTEGER (0) · read-only · obsolete WEB Access action result | |||||||||||||||||
| CacWEBAccessIndex | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.4 | INTEGER (0) | RO | obsolete | |||||||||||||
column · INTEGER (0) · read-only · obsolete WEB Access index | |||||||||||||||||
| CacWEBAccessUserName | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.5 | OCTET STRING (SIZE (0..26)) | RW | obsolete | |||||||||||||
column · OCTET STRING (SIZE (0..26)) · read-write · obsolete WEB Access user name | |||||||||||||||||
| CacWEBAccessUserCode | 1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.6 | OCTET STRING (SIZE (0..26)) | RW | obsolete | |||||||||||||
column · OCTET STRING (SIZE (0..26)) · read-write · obsolete WEB Access user code | |||||||||||||||||
| NauxiliarySettings | 1.3.6.1.4.1.5003.9.10.1.1.3 | ||||||||||||||||
| SenableDiagnostics | 1.3.6.1.4.1.5003.9.10.1.1.3.1 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete The EnableDiagnostics checks the correct functionality of different hardware components on the board. Upon completion, the board sends EV_END_BIT which contains information on the results of the test of each hardware component.
| |||||||||||||||||
| NtrunkSettings | 1.3.6.1.4.1.5003.9.10.1.1.4 | ||||||||||||||||
| TtrunkSettingsTable | 1.3.6.1.4.1.5003.9.10.1.1.4.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Trunks Table | |||||||||||||||||
| RtrunkSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CtrunkId | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.1 | INTEGER (0..32) | RO | obsolete | |||||||||||||
column · INTEGER (0..32) · read-only · obsolete Trunk ID at board in which the call is taking place | |||||||||||||||||
| CclockMaster | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.2 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Selects the trunk clock source. When choosing acCLOCK_MASTER_OFF (= 0) the clock is recovered from the line. When choosing acCLOCK_MASTER_ON (= 1) the trunk clock source is provided by the internal/TDM bus clock source depending on the TDMBusClockSource parameter.
| |||||||||||||||||
| CframingMethod | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.3 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Selects the Framing method to be used for this trunk.
| |||||||||||||||||
| CprotocolType | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.4 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Protocol Type. Sets the PSTN protocol to be used for this trunk.
The protocol type parameter defines the interface
and the specific telephony protocol.
Each protocol defines the following:
1. E1 or T1 physical line configuration.
2. Fixed connection of the relevant time-slots,
which are the Trunks' B-channels, mapping to the 60
(128 for TrunkPack®-VoIP/400) DSP channels.
This limitation is about to change in versions higher than 3.4.
3. Layer 3 specific telephony protocol or transparent mode of operation.
Currently only identical configurations (protocol type, framing method, etc.)
for the two trunks are supported.(see at the TrunkPack®-VoIP User Manual
for available protocols families) relevant only when TDMBusType=FRAMERS.
| |||||||||||||||||
| CterminationSide | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.5 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete For ISDN only. select the ISDN Termination side (layer 2)
| |||||||||||||||||
| CdchConfig | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.6 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Defines D-channel configuration. This setting is only applicable to ISDN PRI protocols that support NFAS and/or D-channel backup procedures.
| |||||||||||||||||
| ClineCode | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.7 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Use to select line code. B8ZS or AMI for T1 spans and HDB3 or AMI for E1 spans.
| |||||||||||||||||
| ClineBuildOutLoss | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.8 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Selects the line build out loss to be used for this trunk
| |||||||||||||||||
| ClineBuildOutOverwrite | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.9 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Overwrite the framer's XPM registers values (these registers control the line pulse shape).
| |||||||||||||||||
| ClineBuildOutXPM0 | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.10 | INTEGER (0..255) | RW | obsolete | |||||||||||||
column · INTEGER (0..255) · read-write · obsolete Controls the Framer's XPM0 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users. | |||||||||||||||||
| ClineBuildOutXPM1 | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.11 | INTEGER (0..255) | RW | obsolete | |||||||||||||
column · INTEGER (0..255) · read-write · obsolete Controls the Framer's XPM1 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert Users. | |||||||||||||||||
| ClineBuildOutXPM2 | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.12 | INTEGER (0..255) | RW | obsolete | |||||||||||||
column · INTEGER (0..255) · read-write · obsolete Controls the Framer's XPM2 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users. | |||||||||||||||||
| CtraceLevel | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.13 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Defines the Protocol Trace level
| |||||||||||||||||
| CacV5InterfaceTrunkGroupId | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.14 | INTEGER (0..31) | RO | obsolete | |||||||||||||
column · INTEGER (0..31) · read-only · obsolete copy from Table 8-1 in LIB manual 4.2beta | |||||||||||||||||
| CacV5LinkIdOld | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.15 | INTEGER (0..255) | RW | obsolete | |||||||||||||
column · INTEGER (0..255) · read-write · obsolete copy from Table 8-1 in LIB manual 4.2beta | |||||||||||||||||
| CacPMStatus | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.16 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete performance Monitoring Enable/Disable.
| |||||||||||||||||
| CacLedStatusColor | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.17 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Trunk led status color
| |||||||||||||||||
| CacLedStatusRate | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.18 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Trunk led status blinking rate
| |||||||||||||||||
| CacIsdnNfasInterfaceId | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.19 | INTEGER (0..255) | RW | obsolete | |||||||||||||
column · INTEGER (0..255) · read-write · obsolete Defines the Interface ID works with NS_EXPLICIT_INTERFACE_ID bit. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. | |||||||||||||||||
| CacTrunkCasTableIndex | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.20 | INTEGER (0..7) | RW | obsolete | |||||||||||||
column · INTEGER (0..7) · read-write · obsolete Index of Cas Table used by this Trunk | |||||||||||||||||
| CacTrunkAdminState | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.21 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Trunk Administrative State
| |||||||||||||||||
| CacPSTNIuaInterfaceId | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.22 | INTEGER (-1..2147483647) | RW | obsolete | |||||||||||||
column · INTEGER (-1..2147483647) · read-write · obsolete IUA trunk interface ID value | |||||||||||||||||
| CacIsdnQ931LayerResponseBehavior | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.23 | INTEGER (-2147483647..2147483647) | RW | obsolete | |||||||||||||
column · INTEGER (-2147483647..2147483647) · read-write · obsolete Bit-field used to determine several behavior options, which influence how the Q.931 protocol behaves. | |||||||||||||||||
| CacIsdnIncomingCallsBehavior | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.24 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-write · obsolete This is the bit-field used to determine several behavior options that influence how the ISDN Stack INCOMING calls behave. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. | |||||||||||||||||
| CacIsdnOutgoingCallsBehavior | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.25 | INTEGER (0..65535) | RW | obsolete | |||||||||||||
column · INTEGER (0..65535) · read-write · obsolete This is the bit-field used to determine several behavior options that influence how the ISDN Stack OUTGOING calls behave. Refer to Appendix A.8 in the 'VoPLib Reference Library User's Manual. | |||||||||||||||||
| CacIsdnGeneralCCBehavior | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.26 | INTEGER (0..65535) | RW | obsolete | |||||||||||||
column · INTEGER (0..65535) · read-write · obsolete This is the bit-field used to determine several general ISDN behavior options. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. | |||||||||||||||||
| CacIsdnNfasGroupNumber | 1.3.6.1.4.1.5003.9.10.1.1.4.1.1.27 | INTEGER (0..4) | RW | obsolete | |||||||||||||
column · INTEGER (0..4) · read-write · obsolete Relevant only for T1 ISDN NFAS trunks indicates the group number of the NFAS group. ;Valid NFAS group numbers are only 1 to 4, 0 indicating that this trunk is not NFAS (in this case the ISDNNFASInterfaceID and DchConfig parameters are ignored). | |||||||||||||||||
| NmGCPSettings | 1.3.6.1.4.1.5003.9.10.1.1.5 | ||||||||||||||||
| ScallAgentIP | 1.3.6.1.4.1.5003.9.10.1.1.5.1 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete MGCP Call Agent IP address to be used for the initial RestartInProgress MGCP message (RSIP) (e.g., 192.10.1.255). Set to 0.0.0.0 to avoid sending RSIP. This parameter if in use overrides the Call Agent IP address provided in BootP. | |||||||||||||||||
| ScallAgentPort | 1.3.6.1.4.1.5003.9.10.1.1.5.2 | INTEGER (0..65534) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..65534) · read-write · obsolete Gate Way will use CallAgentPort as default UDP Port of MGCP Call Agent. | |||||||||||||||||
| ScallAgentDomainName | 1.3.6.1.4.1.5003.9.10.1.1.5.3 | OCTET STRING (SIZE (0..64)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..64)) · read-write · obsolete MGCP Call Agent domain name. | |||||||||||||||||
| SredundantAgentIP | 1.3.6.1.4.1.5003.9.10.1.1.5.4 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete Redundant MGCP call agent IP address for initial RestartInProgress MGCP message (RSIP) e.g. 192.10.1.255. Set to 0 to avoid sending RSIP. | |||||||||||||||||
| SredundantAgentPort | 1.3.6.1.4.1.5003.9.10.1.1.5.5 | INTEGER (0..65534) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..65534) · read-write · obsolete UDP Port of Redundant MGCP call agent. | |||||||||||||||||
| SredundantCallAgentDomainName | 1.3.6.1.4.1.5003.9.10.1.1.5.6 | OCTET STRING (SIZE (0..64)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..64)) · read-write · obsolete Redundant MGCP Call Agent Domain name | |||||||||||||||||
| SdePopulatedChannelsNumber | 1.3.6.1.4.1.5003.9.10.1.1.5.7 | INTEGER (-1..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (-1..2147483647) · read-write · obsolete This parameter can be used to enable MGCP call agent to access only subset of the on board channel bank. Set to -1 (or do not specify) to use all channels. | |||||||||||||||||
| SgateWayName | 1.3.6.1.4.1.5003.9.10.1.1.5.8 | OCTET STRING (SIZE (0..64)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..64)) · read-write · obsolete GateWay Name | |||||||||||||||||
| SendPointName | 1.3.6.1.4.1.5003.9.10.1.1.5.9 | OCTET STRING (SIZE (0..20)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-write · obsolete MGCP: Gateway's end point name. This is a prefix used to identify the endpoint, i.e., 'ACgw' in the following example: '[email protected]'. MEGACO: Prefix of the endpoint part of the termination name | |||||||||||||||||
| SmGCPCommunicationLayerTimeout | 1.3.6.1.4.1.5003.9.10.1.1.5.10 | INTEGER (0..999) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..999) · read-write · obsolete Assumed delay of the communication layer. It is used in retransmission. | |||||||||||||||||
| NacDefaultChannelSettings | 1.3.6.1.4.1.5003.9.10.1.1.6 | ||||||||||||||||
| SacChDefaultDJBufMinDelay | 1.3.6.1.4.1.5003.9.10.1.1.6.1 | INTEGER (0..150) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..150) · read-write · obsolete Dynamic Jitter Buffer Minimum Delay (msec) | |||||||||||||||||
| SacChDefaultDJBufOptFactor | 1.3.6.1.4.1.5003.9.10.1.1.6.2 | INTEGER (0..13) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..13) · read-write · obsolete Dynamic Jitter Buffer frame error/delay optimization. | |||||||||||||||||
| SacChDefaultCallerIDType | 1.3.6.1.4.1.5003.9.10.1.1.6.3 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete The supported caller ID standard types
| |||||||||||||||||
| SacChDefaultFaxModemBypassM | 1.3.6.1.4.1.5003.9.10.1.1.6.4 | INTEGER (1..12) | RW | obsolete | |||||||||||||
scalar · INTEGER (1..12) · read-write · obsolete Number of basic frames to generating one RTP fax/modem bypass packet. | |||||||||||||||||
| SacChDefaultFaxModemRelayVolume | 1.3.6.1.4.1.5003.9.10.1.1.6.5 | INTEGER (-18..-3) | RW | obsolete | |||||||||||||
scalar · INTEGER (-18..-3) · read-write · obsolete Fax gain control. The range -18 to -3 relates to -18.5 dBm to -3.5 dBm in 1 dBm steps. | |||||||||||||||||
| SacChDefaultFaxRelayECMEnable | 1.3.6.1.4.1.5003.9.10.1.1.6.6 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Enables or disables the using of ECM mode during Fax Relay.
| |||||||||||||||||
| SacChDefaultFaxRelayMaxRate | 1.3.6.1.4.1.5003.9.10.1.1.6.7 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Limits the maximum rate at which fax messages are transmitted.
| |||||||||||||||||
| SacChDefaultFaxTransportMode | 1.3.6.1.4.1.5003.9.10.1.1.6.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the Fax over IP transport method.
| |||||||||||||||||
| SacChDefaultModemRelayRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.1.6.9 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Amount of redundancy for fax relay packets
| |||||||||||||||||
| SacChDefaultModemRelayMaxRate | 1.3.6.1.4.1.5003.9.10.1.1.6.10 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Default: Modem Relay Max Rate
| |||||||||||||||||
| SacChDefaultUseT38orFRF11 | 1.3.6.1.4.1.5003.9.10.1.1.6.11 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Selects protocol to send/ receive fax relay.
| |||||||||||||||||
| SacChDefaultV21ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.12 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the V.21 modem transport method (must be set to 0 = disable)
| |||||||||||||||||
| SacChDefaultV22ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.13 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the V.22 modem transport method
| |||||||||||||||||
| SacChDefaultV23ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.14 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the V.23 modem transport method
| |||||||||||||||||
| SacChDefaultV32ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.15 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the V.32 modem transport method
| |||||||||||||||||
| SacChDefaultV34ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.16 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the V.34 modem transport method
| |||||||||||||||||
| SacChDefaultFaxModemBypassCoderType | 1.3.6.1.4.1.5003.9.10.1.1.6.17 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete The User can set the bypass coder (according to the known coders)
| |||||||||||||||||
| SacChDefaultFaxRelayRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.1.6.18 | INTEGER (0..2) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2) · read-write · obsolete Default: Fax Relay Redundancy Depth. Number of repetitions to be applied to each fax relay payload when transmitting to network. | |||||||||||||||||
| SacChDefaultT38ProtectionMode | 1.3.6.1.4.1.5003.9.10.1.1.6.19 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Default: T38 Protection Mode. Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.
| |||||||||||||||||
| SacChDefaultDTMFVolume | 1.3.6.1.4.1.5003.9.10.1.1.6.20 | INTEGER (-31..0) | RW | obsolete | |||||||||||||
scalar · INTEGER (-31..0) · read-write · obsolete DTMF generation Volume Control | |||||||||||||||||
| SacChDefaultDTMFTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.21 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete 0 = Mute = erases digit from voice stream does not relay to remote. 2 = Transparent = digits remains in voice stream. 3 = RFC 2833 relay = erase digit from voice stream relay to remote using RFC 2833 syntax. The other values as seen in the Value List (1 and 7) are not supported as of version 4.4.
| |||||||||||||||||
| SacChDefaultMFTransportType | 1.3.6.1.4.1.5003.9.10.1.1.6.22 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete 0 = erase MFs from voice transport not relayed to remote. 2 = MFs not erased not relayed to remote. 3 = MFs are muted from the voice stream & relayed according to RFC 2833.
| |||||||||||||||||
| SacChDefaultInputGain | 1.3.6.1.4.1.5003.9.10.1.1.6.23 | INTEGER (-32..31) | RW | obsolete | |||||||||||||
scalar · INTEGER (-32..31) · read-write · obsolete PCM input gain. The range is 31 dB to +31 dB in 1 dB steps. | |||||||||||||||||
| SacChDefaultRTPRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.1.6.24 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Enables or disables generation of RFC 2198 redundancy packets.
| |||||||||||||||||
| SacChDefaultTestMode | 1.3.6.1.4.1.5003.9.10.1.1.6.25 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Testing mode applied. 0 = Coder Loopback performs an encoder/decoder loopback inside DSP device. 1 = PCMLoopback loops back incoming PCM to the outgoing PCM. 2 = ToneInjection generates a 1000 Hz tone to outgoing PCM. 3 = NoLoopback sets the channel to work in normal mode.
| |||||||||||||||||
| SacChDefaultVoiceVolume | 1.3.6.1.4.1.5003.9.10.1.1.6.26 | INTEGER (-32..31) | RW | obsolete | |||||||||||||
scalar · INTEGER (-32..31) · read-write · obsolete Voice output gain control the range is -31 dB to +31 dB in 1 dB steps -32 = mute. | |||||||||||||||||
| SacChDefaultM | 1.3.6.1.4.1.5003.9.10.1.1.6.27 | INTEGER (1..12) | RW | obsolete | |||||||||||||
scalar · INTEGER (1..12) · read-write · obsolete Number of DSP payloads for generating one RTP packet | |||||||||||||||||
| SacChDefaultFlashHookPeriod | 1.3.6.1.4.1.5003.9.10.1.1.6.28 | INTEGER (0..65535) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..65535) · read-write · obsolete Flash hook period. | |||||||||||||||||
| SacChDefaultDTMFDetectionPoint | 1.3.6.1.4.1.5003.9.10.1.1.6.29 | INTEGER (0..1) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..1) · read-write · obsolete Defines if the detection of DTMF events is notified at the end of DTMF or at the start of DTMF. | |||||||||||||||||
| SacChDefaultRtpIpTos | 1.3.6.1.4.1.5003.9.10.1.1.6.30 | INTEGER (0..15) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..15) · read-write · obsolete Sets value of IP Type Of Service field in IP header for all packets generated from this channel. Follow the acTIPTOS enumeration. | |||||||||||||||||
| SacChDefaultRtpIpPrecedence | 1.3.6.1.4.1.5003.9.10.1.1.6.31 | INTEGER (0..7) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..7) · read-write · obsolete Sets value of the IP precedence field in the IP header for all packets generated from this channel. Follow the acTIPPrecedence enumeration. | |||||||||||||||||
| SacChDefaultEchoCancler | 1.3.6.1.4.1.5003.9.10.1.1.6.32 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Controls the activation of the Echo Canceler (refer also to 'ForceEchoOff')
| |||||||||||||||||
| SacChDefaultSilenceSuppression | 1.3.6.1.4.1.5003.9.10.1.1.6.33 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Silence Suppression mode
| |||||||||||||||||
| SacChDefaultEchoCanclerHybridLoss | 1.3.6.1.4.1.5003.9.10.1.1.6.34 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets worst case ratio between signal level transmitted to hybrid & echo level returning from hybrid. Set this per worst hybrid in the system in terms of echo return loss. Refer to acTECHybridLoss enumeration:
| |||||||||||||||||
| SacChDefaultPacketizationPeriod | 1.3.6.1.4.1.5003.9.10.1.1.6.35 | INTEGER (5..80) | RW | obsolete | |||||||||||||
scalar · INTEGER (5..80) · read-write · obsolete Packetization Period | |||||||||||||||||
| NaTMSettings | 1.3.6.1.4.1.5003.9.10.1.1.7 | ||||||||||||||||
| SvPMask | 1.3.6.1.4.1.5003.9.10.1.1.7.1 | INTEGER (0..255) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..255) · read-write · obsolete VP masking bits used for address resolution | |||||||||||||||||
| SvCMask | 1.3.6.1.4.1.5003.9.10.1.1.7.2 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VC masking bits used for address resolution | |||||||||||||||||
| SexternalClk | 1.3.6.1.4.1.5003.9.10.1.1.7.3 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Source clock of on the board UTOPIA bus
| |||||||||||||||||
| SaTMLoopBack | 1.3.6.1.4.1.5003.9.10.1.1.7.4 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Phy loopback. The loopback can be used for testing purposes. The loopback direction is towards the PSTN side
| |||||||||||||||||
| SutopiaSlave | 1.3.6.1.4.1.5003.9.10.1.1.7.5 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete UTOPIA interface mode of bus arbitration
| |||||||||||||||||
| SmultyPhy | 1.3.6.1.4.1.5003.9.10.1.1.7.6 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete UTOPIA interface SinglePhy or MultiPhy mode
| |||||||||||||||||
| SslavePhyNum | 1.3.6.1.4.1.5003.9.10.1.1.7.7 | INTEGER (-1..31) | RW | obsolete | |||||||||||||
scalar · INTEGER (-1..31) · read-write · obsolete Provides the slave number for this device (board) in the UTOPIA system bus (Applies to slave mode only) | |||||||||||||||||
| SutopiaBus16 | 1.3.6.1.4.1.5003.9.10.1.1.7.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete UTOPIA interface mode of bus width
| |||||||||||||||||
| SaTMPHYType | 1.3.6.1.4.1.5003.9.10.1.1.7.9 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete External interface type of the board
| |||||||||||||||||
| SdisablePayloadScrambling | 1.3.6.1.4.1.5003.9.10.1.1.7.10 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Disable/Enable Cell payload scrambling in the ATM PHY
| |||||||||||||||||
| SpHYClkSource | 1.3.6.1.4.1.5003.9.10.1.1.7.11 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete OC3 Tx clock source
| |||||||||||||||||
| SsendIdleCASUponLinkFail | 1.3.6.1.4.1.5003.9.10.1.1.7.12 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete This I.366.2 allows sending a special idle CAS packet which signals that the other side has a failure
| |||||||||||||||||
| SmasterSlaveMode | 1.3.6.1.4.1.5003.9.10.1.1.7.13 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Loop Emulation Mode (vmoa145) Master/Slave mode
| |||||||||||||||||
| SvccProfile | 1.3.6.1.4.1.5003.9.10.1.1.7.14 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Determine the required combination of Board's maximal number of VCC and maximal number of channels per VCC
| |||||||||||||||||
| StPNCPVPI | 1.3.6.1.4.1.5003.9.10.1.1.7.15 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VPI used for transferring TPNCP command over AAL5 transport layer | |||||||||||||||||
| StPNCPVCI | 1.3.6.1.4.1.5003.9.10.1.1.7.16 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VCI used for transferring TPNCP command over AAL5 transport layer | |||||||||||||||||
| SsAALLink0VPI | 1.3.6.1.4.1.5003.9.10.1.1.7.17 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VPI of the 1st SAAL link (number 0) | |||||||||||||||||
| SsAALLink0VCI | 1.3.6.1.4.1.5003.9.10.1.1.7.18 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VCI of the 1st SAAL link (number 0) | |||||||||||||||||
| SsAALLink1VPI | 1.3.6.1.4.1.5003.9.10.1.1.7.19 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VPI of the 2nd SAAL link (number 1) | |||||||||||||||||
| SsAALLink1VCI | 1.3.6.1.4.1.5003.9.10.1.1.7.20 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete VCI of the 1st SAAL link (number 1) | |||||||||||||||||
| NacSS7Settings | 1.3.6.1.4.1.5003.9.10.1.1.8 | ||||||||||||||||
| TacSS7SettingsTable | 1.3.6.1.4.1.5003.9.10.1.1.8.1 | NA | obsolete | ||||||||||||||
| RacSS7SettingsEntry | 1.3.6.1.4.1.5003.9.10.1.1.8.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CacSS7LinkId | 1.3.6.1.4.1.5003.9.10.1.1.8.1.1.1 | INTEGER (0..8) | RW | obsolete | |||||||||||||
column · INTEGER (0..8) · read-write · obsolete SS7 Link Id. | |||||||||||||||||
| CacSS7traceLevel | 1.3.6.1.4.1.5003.9.10.1.1.8.1.1.2 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete .
| |||||||||||||||||
| NacConfigFiles | 1.3.6.1.4.1.5003.9.10.1.1.11 | ||||||||||||||||
| SacFxsCoefficients | 1.3.6.1.4.1.5003.9.10.1.1.11.1 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · obsolete The FXS coefficient file name. | |||||||||||||||||
| SacFxoCoefficients | 1.3.6.1.4.1.5003.9.10.1.1.11.2 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · obsolete The FXO coefficient file name. | |||||||||||||||||
| SacCptFile | 1.3.6.1.4.1.5003.9.10.1.1.11.3 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · obsolete . | |||||||||||||||||
| SacVpFile | 1.3.6.1.4.1.5003.9.10.1.1.11.4 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · obsolete The name (and path) of the file containing the voice prompts | |||||||||||||||||
| NacCasTables | 1.3.6.1.4.1.5003.9.10.1.1.11.21 | ||||||||||||||||
| TacCasTablesTable | 1.3.6.1.4.1.5003.9.10.1.1.11.21.1 | NA | obsolete | ||||||||||||||
| RacCasTablesEntry | 1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CacCasTableIndex | 1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.1 | INTEGER (0..7) | RO | obsolete | |||||||||||||
column · INTEGER (0..7) · read-only · obsolete Cas Table Indexd | |||||||||||||||||
| CacCasTabeName | 1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.2 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
column · OCTET STRING (SIZE (0..255)) · read-only · obsolete Cas Table Name | |||||||||||||||||
| NacFxs | 1.3.6.1.4.1.5003.9.10.1.1.12 | ||||||||||||||||
| SacPolarityReversalType | 1.3.6.1.4.1.5003.9.10.1.1.12.1 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Sets the type of the polarity reversal signal used for the network far-end answer and disconnect indications. Smooth reversal prevents negative effects as non-required ringing.
| |||||||||||||||||
| NmegacoSettings | 1.3.6.1.4.1.5003.9.10.1.1.13 | ||||||||||||||||
| SmegacoCurrentProfile | 1.3.6.1.4.1.5003.9.10.1.1.13.1 | INTEGER (1..8191) | RW | obsolete | |||||||||||||
scalar · INTEGER (1..8191) · read-write · obsolete Use this parameter to MGCP/MEGACO beheviour for specific compatibility. See user manual. | |||||||||||||||||
| SmegacoGatewayName | 1.3.6.1.4.1.5003.9.10.1.1.13.2 | OCTET STRING (SIZE (0..64)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..64)) · read-write · obsolete MGCP:Gateway's identification name towards the MGCP Call Agent. If empty Gateway name holds the IP address of the board MEGACO: Prefix of the gateway part of the termination name | |||||||||||||||||
| SmegacoEndpointName | 1.3.6.1.4.1.5003.9.10.1.1.13.3 | OCTET STRING (SIZE (0..20)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-write · obsolete Megaco Endpoint Name | |||||||||||||||||
| SmegacoTrunkName | 1.3.6.1.4.1.5003.9.10.1.1.13.4 | OCTET STRING (SIZE (0..20)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-write · obsolete MGCP: Together with 'EndpointPrefix' field generates local endpoint name on trunk enabled gateways MEGACO: Prefix of the trunk part of the termination name | |||||||||||||||||
| SmegacoActiveCallAgentIp | 1.3.6.1.4.1.5003.9.10.1.1.13.5 | OCTET STRING (SIZE (0..20)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-only · obsolete Megaco Active Call Agent | |||||||||||||||||
| SmegacoActiveCallAgentPort | 1.3.6.1.4.1.5003.9.10.1.1.13.6 | INTEGER (0..32767) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..32767) · read-only · obsolete Megaco Active Port | |||||||||||||||||
| NmegacoCallAgents | 1.3.6.1.4.1.5003.9.10.1.1.13.7 | ||||||||||||||||
| TmegacoCallAgentsTable | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Magaco Call agents Table | |||||||||||||||||
| RmegacoCallAgentsEntry | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CmegacoCallAgentId | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.1 | INTEGER (0..4) | RO | obsolete | |||||||||||||
column · INTEGER (0..4) · read-only · obsolete Megaco Call Agent Id | |||||||||||||||||
| CmegacoCallAgentIp | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.2 | OCTET STRING (SIZE (0..20)) | RW | obsolete | |||||||||||||
column · OCTET STRING (SIZE (0..20)) · read-write · obsolete Megaco CallAgent IP | |||||||||||||||||
| CmegacoCallAgentPort | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.3 | INTEGER (0..32767) | RW | obsolete | |||||||||||||
column · INTEGER (0..32767) · read-write · obsolete List of up to 10 UDP Ports of MEGACO Call Agent separated by , or ;. | |||||||||||||||||
| CmegacoCallAgentIsUsed | 1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.4 | INTEGER | RW | obsolete | |||||||||||||
column · INTEGER · read-write · obsolete Is this index used
| |||||||||||||||||
| SmegacoCheckLegalityOfMGC | 1.3.6.1.4.1.5003.9.10.1.1.13.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete This parameter specified if the MEGACO will reject commands from an MGC not in the provisioned list
| |||||||||||||||||
| NacPSTNParameters | 1.3.6.1.4.1.5003.9.10.1.1.14 | ||||||||||||||||
| SacQ931RELAYMODE | 1.3.6.1.4.1.5003.9.10.1.1.14.1 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete ISDN level 3 mode
| |||||||||||||||||
| SacIsdnDuplicateQ931BuffMode | 1.3.6.1.4.1.5003.9.10.1.1.14.2 | INTEGER (0..255) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..255) · read-write · obsolete Activates / de-activates delivery of raw Q.931 messages. This Object is obsolete and is replaces by acTrunkISDNCommonDuplicateQ931BuffMode in the acPSTN-MIB. | |||||||||||||||||
| SacPSTNCASTableNum | 1.3.6.1.4.1.5003.9.10.1.1.14.3 | INTEGER (0..8) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..8) · read-only · obsolete Indicates how many CAS protocol configuration files are loaded, when 0 is no CAS table. It should match the number of fields. | |||||||||||||||||
| NaMsConfiguration | 1.3.6.1.4.1.5003.9.10.1.1.51 | ||||||||||||||||
| SamsNumOfConferencePorts | 1.3.6.1.4.1.5003.9.10.1.1.51.1 | INTEGER (0..480) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..480) · read-write · obsolete Number Of Conference ports. How many ports on the TPM are allocated to the conferencing service. | |||||||||||||||||
| SamsNumOfTestTrunkPorts | 1.3.6.1.4.1.5003.9.10.1.1.51.2 | INTEGER (0..480) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..480) · read-write · obsolete Number Of Test Trunk ports. How many ports on the TPM are allocated to the Test Trunk service. | |||||||||||||||||
| SamsNumOfLawfulInterceptPorts | 1.3.6.1.4.1.5003.9.10.1.1.51.3 | INTEGER (0..480) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..480) · read-write · obsolete Number Of Test Trunk ports. How many ports on the TPM are allocated to the Lawful Intercept service. | |||||||||||||||||
| SamsNumOfAnnouncementPorts | 1.3.6.1.4.1.5003.9.10.1.1.51.4 | INTEGER (0..480) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..480) · read-write · obsolete Number Of Test Trunk ports. How many ports on the TPM are allocated to the Announcement service. | |||||||||||||||||
| SamsApsIpAddress | 1.3.6.1.4.1.5003.9.10.1.1.51.5 | IpAddress | RW | obsolete | |||||||||||||
scalar · IpAddress · read-write · obsolete Sets the destination IP to which the heartbeat packets are sent. | |||||||||||||||||
| SamsApsPort | 1.3.6.1.4.1.5003.9.10.1.1.51.6 | INTEGER (0..64000) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..64000) · read-write · obsolete Sets the destination UDP port to which the heartbeat packets are sent. | |||||||||||||||||
| SamsPrimaryLanguage | 1.3.6.1.4.1.5003.9.10.1.1.51.7 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Primary Language
| |||||||||||||||||
| SamsSecondaryLanguage | 1.3.6.1.4.1.5003.9.10.1.1.51.8 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Secondary Language
| |||||||||||||||||
| SamsProfile | 1.3.6.1.4.1.5003.9.10.1.1.51.9 | INTEGER (0..32) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..32) · read-write · obsolete AMS Profile Bit Mask: 1'st bit - APS Audio Enable/Disable 2'nd bit - Trunks Interface On/Off 3'td bit - Board Operation State change on ATM Port failure Enable/Disable. | |||||||||||||||||
| SamsAASPackagesProfile | 1.3.6.1.4.1.5003.9.10.1.1.51.10 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete .
| |||||||||||||||||
| NacFeatureKey | 1.3.6.1.4.1.5003.9.10.1.1.90 | ||||||||||||||||
| SacFeatureKeyString | 1.3.6.1.4.1.5003.9.10.1.1.90.1 | OCTET STRING (SIZE (0..256)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..256)) · read-write · obsolete Coded Key specific for board and required features. | |||||||||||||||||
| SacActiveFeaturesList | 1.3.6.1.4.1.5003.9.10.1.1.90.2 | OCTET STRING (SIZE (0..484)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..484)) · read-only · obsolete List of all avtivated features. | |||||||||||||||||
| Nsupplementary | 1.3.6.1.4.1.5003.9.10.1.1.99 | ||||||||||||||||
| SsupplementaryField | 1.3.6.1.4.1.5003.9.10.1.1.99.1 | OCTET STRING (SIZE (0..255)) | RW | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-write · obsolete Flexible INI file line. | |||||||||||||||||
| NboardInformation | 1.3.6.1.4.1.5003.9.10.1.2 | ||||||||||||||||
| SboardType | 1.3.6.1.4.1.5003.9.10.1.2.1 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete The type of the Board.
| |||||||||||||||||
| SboardName | 1.3.6.1.4.1.5003.9.10.1.2.2 | OCTET STRING (SIZE (0..20)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-only · obsolete The name fo the board | |||||||||||||||||
| SserialNum | 1.3.6.1.4.1.5003.9.10.1.2.3 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete serial number of board. | |||||||||||||||||
| SdSPCount | 1.3.6.1.4.1.5003.9.10.1.2.4 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete DSP Count | |||||||||||||||||
| SchannelsCount | 1.3.6.1.4.1.5003.9.10.1.2.5 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Channel Count. | |||||||||||||||||
| ScPUSpeed | 1.3.6.1.4.1.5003.9.10.1.2.6 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete CPU Speed | |||||||||||||||||
| SsoftwareVersion | 1.3.6.1.4.1.5003.9.10.1.2.7 | OCTET STRING (SIZE (0..20)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..20)) · read-only · obsolete TrunkPack Software Version | |||||||||||||||||
| StrunkPackSoftwareDate | 1.3.6.1.4.1.5003.9.10.1.2.8 | OCTET STRING (SIZE (0..40)) | RO | obsolete | |||||||||||||
scalar · OCTET STRING (SIZE (0..40)) · read-only · obsolete TrunkPack Software Date | |||||||||||||||||
| SslotNumber | 1.3.6.1.4.1.5003.9.10.1.2.9 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Slot number | |||||||||||||||||
| SiniFileVersion | 1.3.6.1.4.1.5003.9.10.1.2.10 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Ini file version. | |||||||||||||||||
| SacDspType | 1.3.6.1.4.1.5003.9.10.1.2.11 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Dsp Type | |||||||||||||||||
| SacFlashVersion | 1.3.6.1.4.1.5003.9.10.1.2.12 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Flash [BootLoader] Version. | |||||||||||||||||
| SacBoardFxsOrFxo | 1.3.6.1.4.1.5003.9.10.1.2.13 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete Board is Fxs Or Fxo
| |||||||||||||||||
| SacTrunkslCount | 1.3.6.1.4.1.5003.9.10.1.2.14 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Trunks Count. | |||||||||||||||||
| SacDspVersionTemplate | 1.3.6.1.4.1.5003.9.10.1.2.15 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete selects the DSP load number, which defines the supported set of coders. Default=0 Each template assigns a specific version to each DSP. Each DSP version supports a set of coders and features. The number of channels supported by the DSP can also vary between DSP versions. The total number of channels supported by the board depends on the selected template. | |||||||||||||||||
| SacFirstPortDuplexMode | 1.3.6.1.4.1.5003.9.10.1.2.16 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete full-duplex or half-duplex connection
| |||||||||||||||||
| SacFirstPortSpeed | 1.3.6.1.4.1.5003.9.10.1.2.17 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete .
| |||||||||||||||||
| SacMeanFreeChannels | 1.3.6.1.4.1.5003.9.10.1.2.18 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Mean of Free Channels | |||||||||||||||||
| SacMaxFreeChannels | 1.3.6.1.4.1.5003.9.10.1.2.19 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Max of Free Channels | |||||||||||||||||
| SacSysUpTime | 1.3.6.1.4.1.5003.9.10.1.2.20 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-only · obsolete Time (in Seconds) that the board is alive. | |||||||||||||||||
| SacPhysicalModCount | 1.3.6.1.4.1.5003.9.10.1.2.21 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete .
| |||||||||||||||||
| SacBoardTemperature | 1.3.6.1.4.1.5003.9.10.1.2.22 | INTEGER (0..100) | RO | obsolete | |||||||||||||
scalar · INTEGER (0..100) · read-only · obsolete Temperature of the board in degrees Celsius, should not go higher then 60! | |||||||||||||||||
| NchannelConfiguration | 1.3.6.1.4.1.5003.9.10.1.3 | ||||||||||||||||
| NvoiceSettings | 1.3.6.1.4.1.5003.9.10.1.3.2 | ||||||||||||||||
| TvoiceSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.2.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in voice SettingsTable uniquely identify a voice parameters of channel. | |||||||||||||||||
| RvoiceSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CcID | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.1 | INTEGER (0..2147483647) | RO | deprecated | |||||||||||||
column · INTEGER (0..2147483647) · read-only · deprecated Channel ID | |||||||||||||||||
| Ccoder | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.2 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Digital voice coder
| |||||||||||||||||
| CeCE | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.3 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Enable/Disable Echo Canceler
| |||||||||||||||||
| CsCE | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.4 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Enable/Disable Silence Compresion mechanism
| |||||||||||||||||
| CpFE | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.5 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Post Filter Enable of the voice coder
| |||||||||||||||||
| ChPFE | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.6 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated High Pass Filter Enabled of the voice coder
| |||||||||||||||||
| CtestMode | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.7 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Testing mode to be applied. Valid Range:CoderLoopback will perform an encoder-decoder loopback inside the DSP device, PCMLoopback will loopback the incoming PCM to the outgoing PCM, ToneInjection will generate a1000 Hz tone to outgoing PCM and NoLoopback will set the channel to work in a normal mode. Refer to TTestCode enumeration (default =3= NoLoopBack).
| |||||||||||||||||
| CvoiceVolume | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.8 | INTEGER (0..63) | RO | deprecated | |||||||||||||
column · INTEGER (0..63) · read-only · deprecated Voice Volume sets the voice decoders output gain Range: 0-63 corresponding to -31 dB to +31 dB in 1 dB steps | |||||||||||||||||
| CinputGain | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.9 | INTEGER (0..63) | RO | deprecated | |||||||||||||
column · INTEGER (0..63) · read-only · deprecated PCM input gain sets the gain at the encoders input. | |||||||||||||||||
| Cm | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.10 | INTEGER (1..12) | RO | deprecated | |||||||||||||
column · INTEGER (1..12) · read-only · deprecated This Packet Multiply Factor is the Number of 20 msec payloads (30 msec for G.723) to be used for generating one RTP packet. Range: 1 - Until max Tx/Rx buffer size is reached | |||||||||||||||||
| CrTPRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.11 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated RTP Redundancy Depth. Number of repetitions to be applied to each RTP payload when transmitting to network. apply redundancy sequence per RFC2198. Valid range: Disable redundancy packets generation = 0. Enable generation of RFC2198 redundancy packets = 1.
| |||||||||||||||||
| CeCLength | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.12 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Length of echo canceler tail to be used according to TECLength enumeration. Note that EC length has different length limitations for different boards.
| |||||||||||||||||
| CeCHybridLoss | 1.3.6.1.4.1.5003.9.10.1.3.2.1.1.13 | INTEGER | RO | deprecated | |||||||||||||
column · INTEGER · read-only · deprecated Echo Cancler Hybrid Loss. sets the worst case ratio between the signal level transmitted to the hybrid and the echo level returning from the hybrid. User should set this value according to the worst hybrid in the system in terms of echo return loss according to enum TECHybridLoss enumeration
| |||||||||||||||||
| NfaxModemSettings | 1.3.6.1.4.1.5003.9.10.1.3.3 | ||||||||||||||||
| TfaxModemSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.3.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in faxModem Settings Table uniquely identify fax and modem parameters channel. | |||||||||||||||||
| RfaxModemSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CfAXTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.1 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete FAX Transport Type.
| |||||||||||||||||
| CacCallerIDType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.2 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete CallerID Type.
| |||||||||||||||||
| Cv21ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.3 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete V21 Modem Transpor tType.
| |||||||||||||||||
| Cv22ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.4 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete V22 Modem Transpor tType.
| |||||||||||||||||
| Cv23ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.5 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete V23 Modem Transpor tType.
| |||||||||||||||||
| Cv32ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.6 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete V32 Modem Transpor tType.
| |||||||||||||||||
| Cv34ModemTransportType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.7 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete V34 Modem Transpor tType.
| |||||||||||||||||
| CfaxRelayMaxRate | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.8 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Fax Relay Max Rate Limits the maximum rate at which fax messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).
| |||||||||||||||||
| CmodemRelayMaxRate | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.9 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Modem Relay Max Rate Limits the maximum rate at which modem relay messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).
| |||||||||||||||||
| CfaxRelayECMEnable | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.10 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Fax Relay ECM Enable Enable using ECM mode during Fax Relay.
| |||||||||||||||||
| Ct38FaxRelayProtectionMode | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.11 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete T38 Fax Relay Protection Mode Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.
| |||||||||||||||||
| CfaxRelayRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.12 | INTEGER (0..4) | RO | obsolete | |||||||||||||
column · INTEGER (0..4) · read-only · obsolete Fax Relay Redundancy Depth Number of repetitions to be applied to each fax relay payload when transmitting to network (applicable only when acTFaxModemCmdacTFaxModemSettings.T38FaxRelayProtectionMode=0). | |||||||||||||||||
| CenhancedFaxRelayRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.13 | INTEGER (0..4) | RO | obsolete | |||||||||||||
column · INTEGER (0..4) · read-only · obsolete Enhanced Fax Relay Redundancy Depth Number of repetitions to be applied to control packets when using T.38 standard. | |||||||||||||||||
| CmodemRelayRedundancyDepth | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.14 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Modem Relay Redundancy Depth Number of repetitions to be applied to each modem relay payload when transmitting to network.
| |||||||||||||||||
| CfaxModemRelayVolume | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.15 | INTEGER (-18..15) | RO | obsolete | |||||||||||||
column · INTEGER (-18..15) · read-only · obsolete Fax Modem Relay Volume Fax gain control. Range: -18 - 15 corresponding to -18.5 dBm to -3.5 dBm in 1 dB steps. The reason the range extends to 15 is for backward compatibility. (Default =6). | |||||||||||||||||
| CfaxModemBypassCoderType | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.16 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Fax Modem Bypass Coder Type Coder to be used while performing fax/modem bypass. Usually, high bit rate coders such as G.711 and G.726/G.727 should be used. (Default = G.711 A-law).
| |||||||||||||||||
| CfaxModemBypassM | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.17 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Fax Modem Bypass M Number of 20 msec payloads to be used for generating one RTP fax/modem bypass packet. Range: 1 - Until max Tx/Rx buffer size is reached | |||||||||||||||||
| CuseT38orFRF11 | 1.3.6.1.4.1.5003.9.10.1.3.3.1.1.18 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete Use T38 or FRF11 Use T.38 protocol or proprietary FRF.11 syntax, to send/receive fax relay.
| |||||||||||||||||
| NdJBSettings | 1.3.6.1.4.1.5003.9.10.1.3.4 | ||||||||||||||||
| TdJBSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.4.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in dJB Settings Table uniquely identify jitter buffer parameters of channel. | |||||||||||||||||
| RdJBSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.4.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CdJBufMinDelay | 1.3.6.1.4.1.5003.9.10.1.3.4.1.1.1 | INTEGER (0..150) | RO | obsolete | |||||||||||||
column · INTEGER (0..150) · read-only · obsolete [Millisec] Dynamic Jitter Buffer Minimum Delay. 0 - 150 (default =150) | |||||||||||||||||
| CdJBufOptFactor | 1.3.6.1.4.1.5003.9.10.1.3.4.1.1.2 | INTEGER (0..12) | RO | obsolete | |||||||||||||
column · INTEGER (0..12) · read-only · obsolete Dynamic Jitter Buffer Optimization Factor. Dynamic jitter buffer frame error/delay optimization. 0 - 12 (default =7) | |||||||||||||||||
| NchannelTDMBusSettings | 1.3.6.1.4.1.5003.9.10.1.3.5 | ||||||||||||||||
| TchannelTDMBusSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.5.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in channel TDM Bus Settings Table, uniquely identify TDM Bus sparameters of channel | |||||||||||||||||
| RchannelTDMBusSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CtDMBusInputPort | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1.1 | INTEGER (0..127) | RO | obsolete | |||||||||||||
column · INTEGER (0..127) · read-only · obsolete TDM Bus Input Port. Together with TDMBusInputChannel, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When using TDMBusType=acFramers this parameter selects the trunkID, in which the incoming B-channel resides. 0-127. | |||||||||||||||||
| CtDMBusInputChannel | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1.2 | INTEGER (0..31) | RO | obsolete | |||||||||||||
column · INTEGER (0..31) · read-only · obsolete TDM Bus Input Channel. Together with TDMBusInputPort, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter selects the incoming B-channel (in this case the valid region is 0-31). | |||||||||||||||||
| CtDMBusOutputDisable | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1.3 | INTEGER | RO | obsolete | |||||||||||||
column · INTEGER · read-only · obsolete TDM Bus Output Disable.
0: Places TDM bus output timeslot in tri-state mode.
Ignored in case of PSTN interface.
1: Enables TDM bus output timeslot.
Ignored in case of PSTN interface.
| |||||||||||||||||
| CtDMBusOutputPort | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1.4 | INTEGER (0..255) | RO | obsolete | |||||||||||||
column · INTEGER (0..255) · read-only · obsolete TDM Bus Output Port. Together with TDMBusOutputChannel, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When this parameter is set to 0xff=255 the boardwise setting (set in acOpenBoard()) will be used. When using TDMBusType=acFramers, this parameter is ignored. 0-31 or 255. | |||||||||||||||||
| CtDMBusOutputChannel | 1.3.6.1.4.1.5003.9.10.1.3.5.1.1.5 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete TDM Bus Output Channel. Together with TDMBusOutputPort, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter is ignored. | |||||||||||||||||
| NtransportSettings | 1.3.6.1.4.1.5003.9.10.1.3.6 | ||||||||||||||||
| TtransportSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.6.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in Transport Table, uniquely identify Transport sparameters of channel. | |||||||||||||||||
| RtransportSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.6.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CuseNIorPCI | 1.3.6.1.4.1.5003.9.10.1.3.6.1.1.1 | INTEGER (0..1) | RO | obsolete | |||||||||||||
column · INTEGER (0..1) · read-only · obsolete Description: Use NI or PCI interface. =1 if channel will use NI interface, =0 if PCI interface. 0- PCI interface: Compressed traffic will be sent/received through the PCI interface. 1- NI interface: RTP-RTCP packets sent/received to/from on board Ethernet interface. (default=1). | |||||||||||||||||
| CdisableSoftIPLoopback | 1.3.6.1.4.1.5003.9.10.1.3.6.1.1.2 | INTEGER (0..1) | RO | obsolete | |||||||||||||
column · INTEGER (0..1) · read-only · obsolete Disable Soft IP Loopback =1 in order to diable soft IP loopback. 0- Enables the hair pin connection made in case two channels on the same board are connected together. 1- Disables the hair pin connection made in case two channels on the same board are connected together. | |||||||||||||||||
| CuniDirectionalRTP | 1.3.6.1.4.1.5003.9.10.1.3.6.1.1.3 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete uni Directional RTP. enables one sided RTP stream - according to niDirectionalRTPMode. enables the User to set the channel to work with unidirectional RTP streams. When UniDirectionalRTP is set to acRTPTxOnly, the receiver part of the channel will be disabled, and only the transmitter (encoder) will work. When UniDirectionalRTP is set to acRTPRxOnly, the transmitter part of the channel will be disabled, and only the receiver (decoder) will work. When UniDirectionalRTP is set to acRTPTxRx, both sides will be enabled. Users should note that when configuring a session between two endpoints, some of the channel configuration parameters must be identical on both sides. Such parameters are the voice coder type, the Fax/Modem transport type and bypass coders. All other configuration parameters are independent. | |||||||||||||||||
| NrTPRTCPSettings | 1.3.6.1.4.1.5003.9.10.1.3.7 | ||||||||||||||||
| TrTPRTCPSettingsTable | 1.3.6.1.4.1.5003.9.10.1.3.7.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in RTP-RTCP Table, uniquely identify RTP-RTCP sparameters of channel. | |||||||||||||||||
| RrTPRTCPSettingsEntry | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CcNAME | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.1 | OCTET STRING (SIZE (0..255)) | RO | obsolete | |||||||||||||
column · OCTET STRING (SIZE (0..255)) · read-only · obsolete RTP Canonical Name. Should be unique among all participants within one RTP session. Refer to RFC1890 for more information. Up to 255 characters string. (default ='ChX', X=CID). | |||||||||||||||||
| CiPPrecedence | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.2 | INTEGER (0..7) | RO | obsolete | |||||||||||||
column · INTEGER (0..7) · read-only · obsolete IP Precedence. Sets the value of the IP precedence field in the IP header for all the packets to be generated from this channel. Follow the acTIPPrecedence enumeration. Valid Range: 0-7 (default =0) | |||||||||||||||||
| CiPTOS | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.3 | INTEGER (0..15) | RO | obsolete | |||||||||||||
column · INTEGER (0..15) · read-only · obsolete iP Type Of Service. sets the value of the IP Type Of Service field in the IP header for all the packets to be generated from this channel. acNormalServiceTOS=0, acMinimizeMonetaryCostTOS=1, acMaximizeReliabilityTOS=2, acMaximizeThroughputTOS=4, acMinimizeDelayTOS=8 (Follow the acTIPTOS enumeration). | |||||||||||||||||
| ClocalRTPPort | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.4 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Local RTP Port. Local UDP Port to be used for incoming RTP stream to this channel. This parameter also sets the local RTCP and local T.38 ports in offset of 1,2 from LocalRTPPort respectively. The local RTP port must be a number dividable by 10 and must reside within the following range BoardParams.BaseUDPPort-> BoardParams.BaseUDPPort +10*MAX_CID_NUM. | |||||||||||||||||
| CremoteRTPAddr | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.5 | IpAddress | RO | obsolete | |||||||||||||
column · IpAddress · read-only · obsolete Remote RTP Address | |||||||||||||||||
| CremoteRTPPort | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.6 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete IP/UDP Address of the remote endpoint RTP port | |||||||||||||||||
| CremoteT38Addr | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.7 | IpAddress | RO | obsolete | |||||||||||||
column · IpAddress · read-only · obsolete remote T38 Address | |||||||||||||||||
| CremoteT38Port | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.8 | INTEGER (0..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete IP/UDP Address of the remote endpoint T.38 port | |||||||||||||||||
| CrTCPMeanTxInterval | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.9 | INTEGER (100..2147483647) | RO | obsolete | |||||||||||||
column · INTEGER (100..2147483647) · read-only · obsolete RTCP Mean Tx Interval. Mean interval [msec] between channel's RTCP reports. | |||||||||||||||||
| CrxRTPPayloadType | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.10 | INTEGER (-2..127) | RO | obsolete | |||||||||||||
column · INTEGER (-2..127) · read-only · obsolete Rx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127 . (default =-1). | |||||||||||||||||
| CtxRTPPayloadType | 1.3.6.1.4.1.5003.9.10.1.3.7.1.1.11 | INTEGER (-2..127) | RO | obsolete | |||||||||||||
column · INTEGER (-2..127) · read-only · obsolete Tx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127. (default =-1). | |||||||||||||||||
| NchannelStatus | 1.3.6.1.4.1.5003.9.10.1.4 | ||||||||||||||||
| TchannelStatusTable | 1.3.6.1.4.1.5003.9.10.1.4.1 | NA | obsolete | ||||||||||||||
table · not-accessible · obsolete Data in voice SettingsTable uniquely identify a voice parameters of channel. | |||||||||||||||||
| RchannelStatusEntry | 1.3.6.1.4.1.5003.9.10.1.4.1.1 | NA | obsolete | ||||||||||||||
row · not-accessible · obsolete
| |||||||||||||||||
| CrTPActive | 1.3.6.1.4.1.5003.9.10.1.4.1.1.1 | INTEGER | RO | deprecated | notActive(0) | ||||||||||||
column · INTEGER · read-only · deprecated RTP Active
Example values from LibreNMS test devices
| |||||||||||||||||
| CbypassNIC | 1.3.6.1.4.1.5003.9.10.1.4.1.1.2 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Bypass NIC Example values from LibreNMS test devices
| |||||||||||||||||
| CpendingIdle | 1.3.6.1.4.1.5003.9.10.1.4.1.1.3 | INTEGER (0..1) | RO | obsolete | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · obsolete Pending Idle Example values from LibreNMS test devices
| |||||||||||||||||
| CtxSilencePeriod | 1.3.6.1.4.1.5003.9.10.1.4.1.1.4 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Tx Silence Period Example values from LibreNMS test devices
| |||||||||||||||||
| CrxSilencePeriod | 1.3.6.1.4.1.5003.9.10.1.4.1.1.5 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Rx Silence Period Example values from LibreNMS test devices
| |||||||||||||||||
| CtxFaxMode | 1.3.6.1.4.1.5003.9.10.1.4.1.1.6 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Tx Fax Mode Example values from LibreNMS test devices
| |||||||||||||||||
| CrxFaxMode | 1.3.6.1.4.1.5003.9.10.1.4.1.1.7 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Rx Fax Mode Example values from LibreNMS test devices
| |||||||||||||||||
| CtxDTMFPeriod | 1.3.6.1.4.1.5003.9.10.1.4.1.1.8 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Tx DTMF Period Example values from LibreNMS test devices
| |||||||||||||||||
| CrxDTMFPeriod | 1.3.6.1.4.1.5003.9.10.1.4.1.1.9 | INTEGER (0..1) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..1) · read-only · deprecated Rx DTMF Period Example values from LibreNMS test devices
| |||||||||||||||||
| CpacketsToDSPCnt | 1.3.6.1.4.1.5003.9.10.1.4.1.1.10 | INTEGER (0..2147483647) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · deprecated Jitter Buffer Error Counter Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufErrorCnt | 1.3.6.1.4.1.5003.9.10.1.4.1.1.11 | INTEGER (0..2147483647) | RO | obsolete | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Jitter Buffer Forced Packet count Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufForcedPacketLost | 1.3.6.1.4.1.5003.9.10.1.4.1.1.12 | INTEGER (0..2147483647) | RO | obsolete | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Jitter Buffer Forced Packet Lost Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufForcedPacketAddition | 1.3.6.1.4.1.5003.9.10.1.4.1.1.13 | INTEGER (0..2147483647) | RO | obsolete | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Jitter Buffer Forced Packet Addition Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufUnderRunCnt | 1.3.6.1.4.1.5003.9.10.1.4.1.1.14 | INTEGER (0..2147483647) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · deprecated Jitter Buffer Under-Run Counter Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufOverRunCnt | 1.3.6.1.4.1.5003.9.10.1.4.1.1.15 | INTEGER (0..2147483647) | RO | deprecated | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · deprecated Jitter Buffer Over-Run Counter Example values from LibreNMS test devices
| |||||||||||||||||
| CjitterBufAccumDelay | 1.3.6.1.4.1.5003.9.10.1.4.1.1.16 | INTEGER (0..2147483647) | RO | obsolete | 0 | ||||||||||||
column · INTEGER (0..2147483647) · read-only · obsolete Jitter Buffer accumulation Delay. In packets. Example values from LibreNMS test devices
| |||||||||||||||||
| CfXSorFXO | 1.3.6.1.4.1.5003.9.10.1.4.1.1.17 | INTEGER | RO | deprecated | nonAnalogDevice(-1) | ||||||||||||
column · INTEGER · read-only · deprecated returns the type phisical type of endpoint
Example values from LibreNMS test devices
| |||||||||||||||||
| CchannelHookState | 1.3.6.1.4.1.5003.9.10.1.4.1.1.18 | INTEGER | RO | deprecated | onHook(1) | ||||||||||||
column · INTEGER · read-only · deprecated Channel Hook State
Example values from LibreNMS test devices
| |||||||||||||||||
| Nnotifications | 1.3.6.1.4.1.5003.9.10.1.5 | ||||||||||||||||
| Nreset | 1.3.6.1.4.1.5003.9.10.1.6 | ||||||||||||||||
| SremoteReset | 1.3.6.1.4.1.5003.9.10.1.6.1 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete remote Reset. To remote reset the board, set an integer value to this parameter. Note: Before Reset, The current boardConfiguration parameters will be burned to the board. | |||||||||||||||||
| SacSetDefaults | 1.3.6.1.4.1.5003.9.10.1.6.2 | INTEGER (1..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (1..2147483647) · read-write · obsolete To set the default values, set an integer value to this parameter | |||||||||||||||||
| SacgwAdminState | 1.3.6.1.4.1.5003.9.10.1.6.3 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Determines the gateway's operational state. 0 - locked: Shutdown the GW In the time frame set by acgwAdminStateLockControl 1 - shuttingDown: (read only) Graceful Shutdown is being carried out 2 - unlocked: GW is in service.
| |||||||||||||||||
| SacgwAdminStateLockControl | 1.3.6.1.4.1.5003.9.10.1.6.4 | INTEGER (-1..65535) | RW | obsolete | |||||||||||||
scalar · INTEGER (-1..65535) · read-write · obsolete (in sec) time left for the graceful shutdown to complete. -1 indicates unlimited time frame. 0 indicates immediate (forced) lock. Implementing the control requires setting acgwAdminState to locked. | |||||||||||||||||
| SacSaveConfigToSystem | 1.3.6.1.4.1.5003.9.10.1.6.5 | INTEGER (0..2147483647) | RW | obsolete | |||||||||||||
scalar · INTEGER (0..2147483647) · read-write · obsolete This will save all current configuration in the board onto the flash. Any digit will call on the function. NOTE: Do NOT save the configuration while voice is running - this will cause a delay. | |||||||||||||||||
| SacOperationalState | 1.3.6.1.4.1.5003.9.10.1.6.6 | INTEGER | RO | obsolete | |||||||||||||
scalar · INTEGER · read-only · obsolete The operational state of the gateway.
| |||||||||||||||||
| SremoteResetControl | 1.3.6.1.4.1.5003.9.10.1.6.7 | INTEGER | RW | obsolete | |||||||||||||
scalar · INTEGER · read-write · obsolete Determine the remote reset action 1 - burn staged load image, if any, and config to flash, perform a reset, and load from flash 2 - perform a reset, and load from flash (staged load image, if any, and config is not burned to flash) 3 - perform a reset, and load from bootp/tftp (staged load image, if any, and config burn is not needed) * - an error is returned for any other value Note: The staged load image is an image of a cmp file that was previously loaded to a area in RAM via an HTTP upload
| |||||||||||||||||
| NacTrap | 1.3.6.1.4.1.5003.9.10.1.21 | ||||||||||||||||
| NacBoardTrapGlobals | 1.3.6.1.4.1.5003.9.10.1.21.1 | ||||||||||||||||
| SacBoardTrapGlobalsName | 1.3.6.1.4.1.5003.9.10.1.21.1.1 | INTEGER (0..1000) | RO | ||||||||||||||
scalar · INTEGER (0..1000) · read-only · current trap name | |||||||||||||||||
| SacBoardTrapGlobalsTextualDescription | 1.3.6.1.4.1.5003.9.10.1.21.1.2 | OCTET STRING (SIZE (0..200)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..200)) · read-only · current title of trap | |||||||||||||||||
| SacBoardTrapGlobalsSource | 1.3.6.1.4.1.5003.9.10.1.21.1.3 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current Trap Source - MG1/Shelf1/Board2/Trunk3 | |||||||||||||||||
| SacBoardTrapGlobalsSeverity | 1.3.6.1.4.1.5003.9.10.1.21.1.4 | INTEGER | RO | ||||||||||||||
scalar · INTEGER · read-only · current Trap Severity
| |||||||||||||||||
| SacBoardTrapGlobalsUniqID | 1.3.6.1.4.1.5003.9.10.1.21.1.5 | INTEGER (0..32000) | RO | ||||||||||||||
scalar · INTEGER (0..32000) · read-only · current Trap Uniq Id - generated by AcBoard and should be uniq for the entire EMS | |||||||||||||||||
| SacBoardTrapGlobalsType | 1.3.6.1.4.1.5003.9.10.1.21.1.6 | INTEGER | RO | ||||||||||||||
scalar · INTEGER · read-only · current Trap type - ItuAlarmType
| |||||||||||||||||
| SacBoardTrapGlobalsProbableCause | 1.3.6.1.4.1.5003.9.10.1.21.1.7 | INTEGER | RO | ||||||||||||||
scalar · INTEGER · read-only · current Trap probable cause - SnmpAlarmProbableCause
| |||||||||||||||||
| SacBoardTrapGlobalsAdditionalInfo1 | 1.3.6.1.4.1.5003.9.10.1.21.1.8 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current Trap additional info global field | |||||||||||||||||
| SacBoardTrapGlobalsAdditionalInfo2 | 1.3.6.1.4.1.5003.9.10.1.21.1.9 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current Trap additional info global field | |||||||||||||||||
| SacBoardTrapGlobalsAdditionalInfo3 | 1.3.6.1.4.1.5003.9.10.1.21.1.10 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current Trap additional info global field | |||||||||||||||||
| SacBoardTrapGlobalsDateAndTime | 1.3.6.1.4.1.5003.9.10.1.21.1.11 | DateAndTime | RO | ||||||||||||||
scalar · DateAndTime · read-only · current Date and time that the trap was sent. | |||||||||||||||||
| SacBoardTrapGlobalsSystemSeverity | 1.3.6.1.4.1.5003.9.10.1.21.1.12 | INTEGER | RO | ||||||||||||||
scalar · INTEGER · read-only · current The highest alarm severity on the system.
| |||||||||||||||||
| SacBoardTrapGlobalsDeviceName | 1.3.6.1.4.1.5003.9.10.1.21.1.13 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current acBoardTrapGlobalsDeviceName Used by AC-EMS only | |||||||||||||||||
| SacBoardTrapGlobalsDeviceInfo | 1.3.6.1.4.1.5003.9.10.1.21.1.14 | OCTET STRING (SIZE (0..255)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · current acBoardTrapGlobalsDeviceInfo Used by AC-EMS only | |||||||||||||||||
| SacBoardTrapGlobalsDeviceDescriprion | 1.3.6.1.4.1.5003.9.10.1.21.1.15 | OCTET STRING (SIZE (0..100)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..100)) · read-only · current acBoardTrapGlobalsDeviceDescriprion Used by AC-EMS only | |||||||||||||||||
| SacBoardTrapGlobalsSystemSerialNumber | 1.3.6.1.4.1.5003.9.10.1.21.1.16 | OCTET STRING (SIZE (0..255)) | RO | ||||||||||||||
scalar · OCTET STRING (SIZE (0..255)) · read-only · current NE Serial Number represented as string. | |||||||||||||||||
| NacBoardTrapDefinitions | 1.3.6.1.4.1.5003.9.10.1.21.2 | ||||||||||||||||
| !acBoardFatalError | 1.3.6.1.4.1.5003.9.10.1.21.2.0.1 | ||||||||||||||||
notification · current Board fatal error
| |||||||||||||||||
| !acBoardConfigurationError | 1.3.6.1.4.1.5003.9.10.1.21.2.0.2 | ||||||||||||||||
notification · current Configuration Error
| |||||||||||||||||
| !acBoardTemperatureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.3 | ||||||||||||||||
notification · current Temperature Alarm. Turned on when temperature exceeds 60 degrees Celsius, and relaxes when temperature goes under 55 again.
| |||||||||||||||||
| !acBoardEvBoardStarted | 1.3.6.1.4.1.5003.9.10.1.21.2.0.4 | ||||||||||||||||
notification · current Initialization Ended
| |||||||||||||||||
| !acBoardEvResettingBoard | 1.3.6.1.4.1.5003.9.10.1.21.2.0.5 | ||||||||||||||||
notification · current The board start Reset process - following software reset
| |||||||||||||||||
| !acFeatureKeyError | 1.3.6.1.4.1.5003.9.10.1.21.2.0.6 | ||||||||||||||||
notification · current Feature key related Error
| |||||||||||||||||
| !acgwAdminStateChange | 1.3.6.1.4.1.5003.9.10.1.21.2.0.7 | ||||||||||||||||
notification · current The administrative state of the gate way has been changed to a new state.
| |||||||||||||||||
| !acBoardCallResourcesAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.8 | ||||||||||||||||
notification · current No free channels available
| |||||||||||||||||
| !acBoardControllerFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.9 | ||||||||||||||||
notification · current The GK/Proxy not found or registration failed. internal routing table may be used for routing
| |||||||||||||||||
| !acBoardEthernetLinkAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.10 | ||||||||||||||||
notification · current Ethernet Link is down or remote Ethernet link is down and board has no communication to any other host
| |||||||||||||||||
| !acBoardOverloadAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.11 | ||||||||||||||||
notification · current Overload in one or some of the system's components
| |||||||||||||||||
| !acActiveAlarmTableOverflow | 1.3.6.1.4.1.5003.9.10.1.21.2.0.12 | ||||||||||||||||
notification · current An active alarm could not be placed in the active alarm table because the table is full. This alarm will not clear. Reboot is the only way to completely clear the Active Alarm table overflow problem. Any alarm raised at this state will not be Carrier Grade compatible. Therefore, Updates will not clear the alarm before changing the bindings and re-raising alarms. The History tables remain unaffected. All Alarms raised prior to overflow will remain Carrier Grade compatible. Other alarms, raised after this alarm was raised, that are placed in the Active Alarm table will be Carrier Grade compatible. (This is for when after the alarm was raised there were some clears, clearing alarms off the Active Alarm table).
| |||||||||||||||||
| !acAtmPortAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.13 | ||||||||||||||||
notification · current ATM Port Alarm
| |||||||||||||||||
| !acAudioProvisioningAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.14 | ||||||||||||||||
notification · current This alarm is raised if the Media Server is unable to provision its audio. This could be because the Audio Provisioning System (APS) is down or there is a network problem.
| |||||||||||||||||
| !acOperationalStateChange | 1.3.6.1.4.1.5003.9.10.1.21.2.0.15 | ||||||||||||||||
notification · current This alarm is raised if the operational state of the node goes to disabled. The alarm is cleared when the operational state of the node goes to enabled.
| |||||||||||||||||
| !acKeepAlive | 1.3.6.1.4.1.5003.9.10.1.21.2.0.16 | ||||||||||||||||
notification · current This trap is the NAT Traversal keep alive trap. If the STUN application in the device detects a NAT then this trap will be sent out on a regular time laps - 9/10 of the acSysSTUNBindingLifeTime object. The AdditionalInfo1 varbind has the MAC address of the device. Note that all traps are sent out from the SNMP Port (usually 161).
| |||||||||||||||||
| !acNATTraversalAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.17 | ||||||||||||||||
notification · current When the NAT placed in front a device is identified as a symmetric NAT - this alarm is raised. It is cleared when a non-symmetric NAT or no NAT replace the symmetric one.
| |||||||||||||||||
| !acEnhancedBITStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.18 | ||||||||||||||||
notification · current This trap is used to for the status of the BIT (Built In Test). The information in the trap contains board HW elements being tested and their status. The information is presented in the additional info fields.
| |||||||||||||||||
| !acSS7LinkStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.19 | ||||||||||||||||
notification · current This alarm is raised if the operational state of the SS7 link becomes XXXX. The alarm is cleared when the operational state of the link becomes XXXX.
| |||||||||||||||||
| !acSS7LinkInhibitStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.20 | ||||||||||||||||
notification · current This alarm is raised if the SS7 link becomes inhibited (local or remote). The alarm is cleared when the link becomes uninhibited - local AND remote. Note that this alarm will be raised for any change in the remote or local inhibition status.
| |||||||||||||||||
| !acSS7LinkBlockStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.21 | ||||||||||||||||
notification · current This alarm is raised if the SS7 link becomes blocked (local or remote). The alarm is cleared when the link becomes unblocked - local AND remote. Note that this alarm will be raised for any change in the remote or local blocking status.
| |||||||||||||||||
| !acSS7LinkCongestionStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.22 | ||||||||||||||||
notification · current This alarm is raised if the SS7 link becomes congested (local or remote). The alarm is cleared when the link becomes uncongested - local AND remote. Note that this alarm will be raised for any change in the remote or local congestion status.
| |||||||||||||||||
| !acSS7LinkSetStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.23 | ||||||||||||||||
notification · current This alarm is raised if the operational state of the SS7 linkset becomes BUSY. The alarm is cleared when the operational state of the linkset becomes IN-SERVICE or OFFLINE.
| |||||||||||||||||
| !acSS7RouteSetStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.24 | ||||||||||||||||
notification · current This alarm is raised if the operational state of the SS7 routeset becomes BUSY. The alarm is cleared when the operational state of the routeset becomes IN-SERVICE or OFFLINE.
| |||||||||||||||||
| !acSS7SNSetStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.25 | ||||||||||||||||
notification · current This alarm is raised if the operational state of the SS7 node becomes BUSY. The alarm is cleared when the operational state of the node becomes IN-SERVICE or OFFLINE.
| |||||||||||||||||
| !acSS7RedundancyAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.26 | ||||||||||||||||
notification · current Raised when the SS7 redundancy degregated. Cleared when all entities of redundancy are fully functional and in serveice.
| |||||||||||||||||
| !acPerformanceMonitoringThresholdCrossing | 1.3.6.1.4.1.5003.9.10.1.21.2.0.27 | ||||||||||||||||
notification · current This log trap is sent out for every time the threshold of a Performance Monitored object is crossed. The severity field is 'indeterminate' when the crossing is above the threshold and 'cleared' when it goes back under the threshold. The 'source' varbind in the trap indicates the object for which the threshold is being crossed.
| |||||||||||||||||
| !acHTTPDownloadResult | 1.3.6.1.4.1.5003.9.10.1.21.2.0.28 | ||||||||||||||||
notification · current This trap indicates the result of a recent file download (includes HTTP error code, if available).
| |||||||||||||||||
| !acFanTrayAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.29 | ||||||||||||||||
notification · current This alarm is raised when the fan tray is missing or some of the fans are faulty. If the fan tray is missing or more then X fans are faulty the severity will be Critical. If more then one and less the X fans are faulty the severity will be Major.
| |||||||||||||||||
| !acPowerSupplyAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.30 | ||||||||||||||||
notification · current This alarm is raised when the HA (High Availability) feature is active and one of the power supply units is faulty.
| |||||||||||||||||
| !acPEMAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.31 | ||||||||||||||||
notification · current This alarm is raised when the HA (High Availability) feature is active. The severity is critical if one of the PEM units is missing and major if the electric wire to one of the units is disconnected.
| |||||||||||||||||
| !acSAMissingAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.32 | ||||||||||||||||
notification · current This alarm is raised when the SA module in the M3K MG is missing. Whenthere is no SAT there are no other chassis HW related alarms. Note - relevant only for M3K.
| |||||||||||||||||
| !acHASystemFaultAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.33 | ||||||||||||||||
notification · current This alarm is raised when the HA (High Availability) feature is active and the system is NOT HA. Critical severity - 1.Wrong HW Configuration. 2. Redundant module is missing (not in slot). 3. The redundant module is non operable. Minor severity - waiting for redunadant to connect (after reset!).
| |||||||||||||||||
| !acHASystemConfigMismatchAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.34 | ||||||||||||||||
notification · current This alarm is raised when the HA (High Availability) feature is active and there has been a configuration change due to which the HA system may or may not be usable.
| |||||||||||||||||
| !acHASystemSwitchOverAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.35 | ||||||||||||||||
notification · current This alarm is raised when the HA (High Availability) feature is active and there has been a switchover due to failure or reset in the active module.
| |||||||||||||||||
| !acUserInputAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.36 | ||||||||||||||||
notification · current This Alarm is raised when the input dry contact is short circuited. Cleared when the circuit is reopened.
| |||||||||||||||||
| !acDChannelStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.37 | ||||||||||||||||
notification · current This non alarm trap is sent when establishment, re-establishment or release of LAPD link with its peer connection occurs. The trap will be sent out with one of the following in the textual description: D-channel synchronized D-channel not-synchronized
| |||||||||||||||||
| !acSonetSectionLOFAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.38 | ||||||||||||||||
notification · current SONET section Loss of Frame alarm.
| |||||||||||||||||
| !acSonetSectionLOSAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.39 | ||||||||||||||||
notification · current SONET section Loss of Signal alarm.
| |||||||||||||||||
| !acSonetLineAISAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.40 | ||||||||||||||||
notification · current SONET Line AIS alarm.
| |||||||||||||||||
| !acSonetLineRDIAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.41 | ||||||||||||||||
notification · current SONET Line RDI alarm.
| |||||||||||||||||
| !acSonetIfHwFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.42 | ||||||||||||||||
notification · current SONET or SDH medium Interface has failed.
| |||||||||||||||||
| !acHwFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.43 | ||||||||||||||||
notification · current HW failure alarm.
| |||||||||||||||||
| !acH248LostConnectionWithCA | 1.3.6.1.4.1.5003.9.10.1.21.2.0.44 | ||||||||||||||||
notification · current H248 lost connection with call agent
| |||||||||||||||||
| !acDialPlanFileReplaced | 1.3.6.1.4.1.5003.9.10.1.21.2.0.45 | ||||||||||||||||
notification · current dial plan file replaced notification
| |||||||||||||||||
| !acAnalogPortSPIOutOfService | 1.3.6.1.4.1.5003.9.10.1.21.2.0.46 | ||||||||||||||||
notification · current Analog port out of service
| |||||||||||||||||
| !acAnalogPortHighTemperature | 1.3.6.1.4.1.5003.9.10.1.21.2.0.47 | ||||||||||||||||
notification · current Analog Port High Temperature
| |||||||||||||||||
| !acHitlessUpdateStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.48 | ||||||||||||||||
notification · current Notification trap that is sent out at the beginning and the end of a Hitless SW update. Failure during the process will also instigate the trap. Relevant to HA systems only.
| |||||||||||||||||
| !acTrunksAlarmNearEndLOS | 1.3.6.1.4.1.5003.9.10.1.21.2.0.49 | ||||||||||||||||
notification · current Loss of signal at trunk's near end.
| |||||||||||||||||
| !acTrunksAlarmNearEndLOF | 1.3.6.1.4.1.5003.9.10.1.21.2.0.50 | ||||||||||||||||
notification · current Loss of frame at trunk's near end.
| |||||||||||||||||
| !acTrunksAlarmRcvAIS | 1.3.6.1.4.1.5003.9.10.1.21.2.0.51 | ||||||||||||||||
notification · current Received AIS from trunk's far end.
| |||||||||||||||||
| !acTrunksAlarmFarEndLOF | 1.3.6.1.4.1.5003.9.10.1.21.2.0.52 | ||||||||||||||||
notification · current Loss of frame at trunk's far end.
| |||||||||||||||||
| !acIPv6ErrorAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.53 | ||||||||||||||||
notification · current Alarm trap that is sent out for IPv6 related errors.
| |||||||||||||||||
| !acAMSProcedureResult | 1.3.6.1.4.1.5003.9.10.1.21.2.0.54 | ||||||||||||||||
notification · current AMS procedure related information
| |||||||||||||||||
| !acWeakRedundancy | 1.3.6.1.4.1.5003.9.10.1.21.2.0.55 | ||||||||||||||||
notification · current The system is in weak redundancy mode. Switch over is done with a reset to the board taking over.
| |||||||||||||||||
| !acTMInconsistentRemoteAndLocalPLLStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.56 | ||||||||||||||||
notification · current Inconsistent Remote And Local PLL Status
| |||||||||||||||||
| !acTMReferenceStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.57 | ||||||||||||||||
notification · current Timing manager reference status
| |||||||||||||||||
| !acTMReferenceChange | 1.3.6.1.4.1.5003.9.10.1.21.2.0.58 | ||||||||||||||||
notification · current Timing manager reference Change
| |||||||||||||||||
| !acGWSASEmergencyModeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.59 | ||||||||||||||||
notification · current The alarm is raised when SAS enters the Emergency Mode and then cleared when SAS enters Normal Mode again.
| |||||||||||||||||
| !acV52InterfaceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.60 | ||||||||||||||||
notification · current The alarm is raised for v5.2 interface errors and alarms.{@}For a detailed list of the interfaces' alarms see the acV5InterfceTable.
| |||||||||||||||||
| !acSonetPathSTSLOPAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.61 | ||||||||||||||||
notification · current Sonet Path STS LOP alarm.
| |||||||||||||||||
| !acSonetPathSTSAISAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.62 | ||||||||||||||||
notification · current Sonet Path STS AIS alarm.
| |||||||||||||||||
| !acSonetPathSTSRDIAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.63 | ||||||||||||||||
notification · current Sonet Path STS RDI alarm.
| |||||||||||||||||
| !acSonetPathUnequippedAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.64 | ||||||||||||||||
notification · current Sonet Path Unequipped alarm.
| |||||||||||||||||
| !acSonetPathSignalLabelMismatchAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.65 | ||||||||||||||||
notification · current Sonet Path Signal Label Mismatch alarm.
| |||||||||||||||||
| !acDS3RAIAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.66 | ||||||||||||||||
notification · current DS3 RAI alarm.
| |||||||||||||||||
| !acDS3AISAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.67 | ||||||||||||||||
notification · current DS3 AIS alarm.
| |||||||||||||||||
| !acDS3LOFAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.68 | ||||||||||||||||
notification · current DS3 LOF alarm.
| |||||||||||||||||
| !acDS3LOSAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.69 | ||||||||||||||||
notification · current DS3 LOS alarm.
| |||||||||||||||||
| !acSWUpgradeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.70 | ||||||||||||||||
notification · current Raised for SW upgrade process errors.
| |||||||||||||||||
| !acNTPServerStatusAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.71 | ||||||||||||||||
notification · current NTP server status alarm. {@}Raised when the connection to the NTP server is lost. Cleared when the connection is reestablished. {@}Unset time (as a result of no connection to NTP server) may result with functionality degradation and failure in device.
| |||||||||||||||||
| !acThreeWayConferenceOutOfResources | 1.3.6.1.4.1.5003.9.10.1.21.2.0.72 | ||||||||||||||||
notification · current Three way conference out of resources.
| |||||||||||||||||
| !acSS7AliasPcStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.73 | ||||||||||||||||
notification · current raised when the Alias PC is in BUSY state. Cleared when it is in In-Service state.
| |||||||||||||||||
| !acSS7UalGroupStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.74 | ||||||||||||||||
notification · current Raised when the Ual Group Asp state is not ACTIVE. Cleared when it is Active.
| |||||||||||||||||
| !acLDAPLostConnection | 1.3.6.1.4.1.5003.9.10.1.21.2.0.75 | ||||||||||||||||
notification · current Raised when there is no connection to the LDAP server.
| |||||||||||||||||
| !acAnalogPortGroundFaultOutOfService | 1.3.6.1.4.1.5003.9.10.1.21.2.0.76 | ||||||||||||||||
notification · current Raised when the MP500 FXS port is inactive due to ground fault.
| |||||||||||||||||
| !acSSHConnectionStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.77 | ||||||||||||||||
notification · current This trap indicates the result of a recent SSH connection attempt.
| |||||||||||||||||
| !acOCSPServerStatusAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.78 | ||||||||||||||||
notification · current raised when OCSP connection is not available.
| |||||||||||||||||
| !acBoardWanLinkAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.79 | ||||||||||||||||
notification · current Wan Link is down.
| |||||||||||||||||
| !acPowerOverEthernetStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.80 | ||||||||||||||||
notification · current Raised when PEO resources are over allocated
| |||||||||||||||||
| !acMediaProcessOverloadAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.81 | ||||||||||||||||
notification · current Raised when media process overloads
| |||||||||||||||||
| !acWirelessCellularModemAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.82 | ||||||||||||||||
notification · current Raised when either the wireless modem is down or in backup mode.
| |||||||||||||||||
| !acDataInterfaceStatus | 1.3.6.1.4.1.5003.9.10.1.21.2.0.83 | ||||||||||||||||
notification · current Raised when a DSL interface state changes to up or down.
| |||||||||||||||||
| !acNFASGroupAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.84 | ||||||||||||||||
notification · current Raised when an NFAS group goes Out-Of-Service
| |||||||||||||||||
| !acBChannelAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.85 | ||||||||||||||||
notification · current Raised when B-Channel service state changes
| |||||||||||||||||
| !acEthernetGroupAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.86 | ||||||||||||||||
notification · current Raised when the Ethernet group has no Ethernet port with its link up. Cleared when at least on port has established a link.
| |||||||||||||||||
| !acMediaRealmBWThresholdAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.87 | ||||||||||||||||
notification · current Raised when a BW threshold is crossed
| |||||||||||||||||
| !acNqmConnectivityAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.88 | ||||||||||||||||
notification · current Connectivity with NQM probe destination is lost
| |||||||||||||||||
| !acNqmRttAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.89 | ||||||||||||||||
notification · current Detected high Round Trip Time towards NQM probe destination
| |||||||||||||||||
| !acNqmJitterAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.90 | ||||||||||||||||
notification · current Detected high Jitter towards NQM probe destination
| |||||||||||||||||
| !acNqmPacketLossAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.91 | ||||||||||||||||
notification · current Detected high Packet Loss towards NQM probe destination
| |||||||||||||||||
| !acCertificateExpiryNotification | 1.3.6.1.4.1.5003.9.10.1.21.2.0.92 | ||||||||||||||||
notification · current Send before the expiration of the installed credentials, which cannot be renewed automatically.
| |||||||||||||||||
| !acWEBUserAccessDisabled | 1.3.6.1.4.1.5003.9.10.1.21.2.0.93 | ||||||||||||||||
notification · current Web user was disabled due to inactivity.
| |||||||||||||||||
| !acProxyConnectionLost | 1.3.6.1.4.1.5003.9.10.1.21.2.0.94 | ||||||||||||||||
notification · current Raised when all connections in the proxy set are down.
| |||||||||||||||||
| !acNqmCqMosAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.95 | ||||||||||||||||
notification · current Detected low conversational voice quality towards NQM probe destination
| |||||||||||||||||
| !acNqmLqMosAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.96 | ||||||||||||||||
notification · current Detected low listening voice quality towards NQM probe destination
| |||||||||||||||||
| !acRedundantBoardAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.97 | ||||||||||||||||
notification · current Active board sends notification when an alarm or notification is raised in the redundant board. The information is as follow: acBoardTrapGlobalsAdditionalInfo1: redundants original info acBoardTrapGlobalsAdditionalInfo2: trap Id acBoardTrapGlobalsAdditionalInfo3: redundants serial number
| |||||||||||||||||
| !acHANetworkWatchdogStatusAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.98 | ||||||||||||||||
notification · current Sent when the module was enabled by the user but it is not running.
| |||||||||||||||||
| !acIDSPolicyAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.99 | ||||||||||||||||
notification · current IDS Policy Alarm
| |||||||||||||||||
| !acIDSThresholdCrossNotification | 1.3.6.1.4.1.5003.9.10.1.21.2.0.100 | ||||||||||||||||
notification · current Sent when IDS Threshold is crossed
| |||||||||||||||||
| !acIDSBlacklistNotification | 1.3.6.1.4.1.5003.9.10.1.21.2.0.101 | ||||||||||||||||
notification · current IDS blacklist: Address [IP address with network interface] entered/exited
| |||||||||||||||||
| !acProxyConnectivity | 1.3.6.1.4.1.5003.9.10.1.21.2.0.102 | ||||||||||||||||
notification · current Sent when Proxy IP is offline or inline
| |||||||||||||||||
| !acBoardSignalingCpuUsageThresholdAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.103 | ||||||||||||||||
notification · current Raised when CPU utilization threshold value ( ) crossed [INI-CpuUsageThresholdAlarm].
| |||||||||||||||||
| !acWirelessCellularModemStatusChanged | 1.3.6.1.4.1.5003.9.10.1.21.2.0.104 | ||||||||||||||||
notification · current Indication of change of Wireless Cellular Modem Status
| |||||||||||||||||
| !acActivityLog | 1.3.6.1.4.1.5003.9.10.1.21.2.0.105 | ||||||||||||||||
notification · current Configuration Change event
| |||||||||||||||||
| !acLicensePoolInfraAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.106 | ||||||||||||||||
notification · current will be issued in case of any infra failure
| |||||||||||||||||
| !acLicensePoolApplicationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.107 | ||||||||||||||||
notification · current will be issued by SIP, currently to indicate out of resource problem.
| |||||||||||||||||
| !acHTTPProxyServiceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.108 | ||||||||||||||||
notification · current HTTP proxy service Alarm
| |||||||||||||||||
| !acReservedAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.109 | ||||||||||||||||
notification · current Reserved Alarm
| |||||||||||||||||
| !acResetNeededAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.110 | ||||||||||||||||
notification · current Configuration was changed. Reset the device for the new settings to take effect.
| |||||||||||||||||
| !acASRThresholdAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.111 | ||||||||||||||||
notification · current ASR threshold crossed
| |||||||||||||||||
| !acACDThresholdAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.112 | ||||||||||||||||
notification · current ACD threshold crossed
| |||||||||||||||||
| !acNERThresholdAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.113 | ||||||||||||||||
notification · current NER threshold crossed
| |||||||||||||||||
| !acIpGroupNoRouteAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.114 | ||||||||||||||||
notification · current IP Group is temporarily blocked
| |||||||||||||||||
| !acMtcmClusterHaAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.115 | ||||||||||||||||
notification · current At least one of the MTCEs is inactive, MTC will now provide only partial HA
| |||||||||||||||||
| !acMtceNetworkFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.116 | ||||||||||||||||
notification · current Lost connection with board
| |||||||||||||||||
| !acMtceSwUpgradeFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.117 | ||||||||||||||||
notification · current Reset of the MTCE is required
| |||||||||||||||||
| !acMtceHwTemperatureFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.118 | ||||||||||||||||
notification · current MTCE reached high temperature threshold
| |||||||||||||||||
| !acMtceHwFanTrayFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.119 | ||||||||||||||||
notification · current MTCE fan tray fault
| |||||||||||||||||
| !acMtcePsuFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.120 | ||||||||||||||||
notification · current MTCE power supply unit fault
| |||||||||||||||||
| !acTrackIdStateChangeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.121 | ||||||||||||||||
notification · current Will be issued when a Track goes down or up. Includes track id, interface name, destination adress and a new track state.
| |||||||||||||||||
| !acModuleServiceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.122 | ||||||||||||||||
notification · current Module service fault
| |||||||||||||||||
| !acModuleOperationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.123 | ||||||||||||||||
notification · current Module operation fault
| |||||||||||||||||
| !acPortServiceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.124 | ||||||||||||||||
notification · current Port service fault
| |||||||||||||||||
| !acLicensePoolOverAllocationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.125 | ||||||||||||||||
notification · current Will be issued in case requested License pool exceeds the board ability
| |||||||||||||||||
| !acClusterBandwidthAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.126 | ||||||||||||||||
notification · current Sent when the bandwidth of the cluster Interface utilization is too high.
| |||||||||||||||||
| !acLicensePoolExpirationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.127 | ||||||||||||||||
notification · current Will be issued in case License pool is about or was expired
| |||||||||||||||||
| !acCertificateExpiryAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.128 | ||||||||||||||||
notification · current Send alarm before the expiration of the installed credentials, which cannot be renewed automatically (alarm type). acCertificateExpiryNotification was obsolete.
| |||||||||||||||||
| !acLicenseKeyHitlessUpgradeAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.129 | ||||||||||||||||
notification · current License key hitless upgrade failed due to HA switchover failure.
| |||||||||||||||||
| !acNGINXConfigurationIsInvalidAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.130 | ||||||||||||||||
notification · current NGINX configuration is invalid
| |||||||||||||||||
| !acNGINXPprocessIsNotRunningAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.131 | ||||||||||||||||
notification · current NGINX process is not running
| |||||||||||||||||
| !acCloudLicenseManagerAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.132 | ||||||||||||||||
notification · current Cloud License Manager Alarm; Connection with Cloud License Manager not established or Connection with Cloud License Manager failed (response code).
| |||||||||||||||||
| !acMediaClusterAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.133 | ||||||||||||||||
notification · current Alarm will be raised in case that Cluster is enabled, but there is no Cluster Interface in interface Table.
| |||||||||||||||||
| !acMediaClusterRemoteInterfaceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.134 | ||||||||||||||||
notification · current Media Cluster Remote Interface Alarm;
| |||||||||||||||||
| !acHANetworkMismatchAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.135 | ||||||||||||||||
notification · current Mismatch of network devices in the cloud HA system between active and redundant instances.
| |||||||||||||||||
| !acHANetworkMonitorAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.136 | ||||||||||||||||
notification · current Alarm will be raised when destination <IP address(es)> is unreachable.
| |||||||||||||||||
| !acHAEthernetGroupAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.137 | ||||||||||||||||
notification · current Alarm will be raised when maintenance's Ethernet-group gets an alarm state.
| |||||||||||||||||
| !acFloatingLicenseAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.138 | ||||||||||||||||
notification · current Alarm will be raised when there is not enough memory to allocate custom profile .
| |||||||||||||||||
| !acAWSSecurityRoleAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.139 | ||||||||||||||||
notification · current This alarm is sent when the AWS instance has not been configured with the required IAM role in order to access AWS services and resources.
| |||||||||||||||||
| !acInstallationFailureAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.140 | ||||||||||||||||
notification · current This alarm is sent when one of Installation package was not install; it applicable to Hosted only.
| |||||||||||||||||
| !acAnalogLineLeftOffhookAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.141 | ||||||||||||||||
notification · current This alarm is sent when a phone left Offhook for X seconds, defined by FXSOffhookTimeoutAlarm. The deault value is no alarm.
| |||||||||||||||||
| !acCDRServerAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.142 | ||||||||||||||||
notification · current This alarm is sent when SBC failed to upload CDRs to all configured servers.
| |||||||||||||||||
| !acDSPFarmsMismatchAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.143 | ||||||||||||||||
notification · current This alarm is sent when missing DSP farm was detected.
| |||||||||||||||||
| !acFlexLicenseManagerAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.144 | ||||||||||||||||
notification · current Flex License Manager Alarm; Connection with Flex License Manager not established or Connection with Flex License Manager failed (response code).
| |||||||||||||||||
| !acRemoteMonitoringAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.145 | ||||||||||||||||
notification · current Remote Monitoring Alarm; There is no connetion with remote monitoring server.
| |||||||||||||||||
| !acMeteringAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.146 | ||||||||||||||||
notification · current Warning severity: No connection to AWS marketplace API service will be down in 1 hour. Critical severity: Service down due to lack of connection to AWS marketplace API.
| |||||||||||||||||
| !acSDRServerAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.147 | ||||||||||||||||
notification · current This alarm is sent when SBC failed to upload SDRs to all configured servers.
| |||||||||||||||||
| !acKpiThresholdCrossing | 1.3.6.1.4.1.5003.9.10.1.21.2.0.148 | ||||||||||||||||
notification · current This log trap is sent out for every time the threshold of a Performance Monitored object is crossed. The severity field is 'indeterminate' when the crossing is above the threshold and 'cleared' when it goes back under the threshold. The 'source' varbind in the trap indicates the object for which the threshold is being crossed.
| |||||||||||||||||
| !acClockConfigurationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.149 | ||||||||||||||||
notification · current This alarm is sent when both NTP and Date Header Time Sync are enabled. NTP will be used as the source for the clock sync.
| |||||||||||||||||
| !acDebugRecordingActivationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.150 | ||||||||||||||||
notification · current This alarm is sent when Debug Recording is enabled.
| |||||||||||||||||
| !acMCNotSecuredAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.151 | ||||||||||||||||
notification · current This alarm is raised when the MC is connected using TCP rather than TLS.
| |||||||||||||||||
| !acFaultyDSPAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.152 | ||||||||||||||||
notification · current This alarm is raised when one or more DSPs fail to load properly.
| |||||||||||||||||
| !acDspOperationAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.153 | ||||||||||||||||
notification · current HW failure detected on DSP.
| |||||||||||||||||
| !acTLSCertificateMismatchAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.154 | ||||||||||||||||
notification · current This alarm is raised when there is a mismatch between Certificate and Private Key.
| |||||||||||||||||
| !acNoReplyFromDNSServerAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.155 | ||||||||||||||||
notification · current This alarm is raised when there is no reply from DNS server.
| |||||||||||||||||
| !acWeakPasswordAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.156 | ||||||||||||||||
notification · current This alarm is raised when a user <username> has weak password.
| |||||||||||||||||
| !acVMMaintenaceAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.157 | ||||||||||||||||
notification · current This alarm is raised when the maintenance events monitoring task detects an upcoming event.
| |||||||||||||||||
| !acIPv4ErrorAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.158 | ||||||||||||||||
notification · current Alarm trap that is sent out for IPv4 related errors.
| |||||||||||||||||
| !acTLSSocketsLimitAlarm | 1.3.6.1.4.1.5003.9.10.1.21.2.0.159 | ||||||||||||||||
notification · current The alarm is raised when the number of SIP incoming TLS connections reach 95% of max number supported.
| |||||||||||||||||
Traps / Notifications
- acACDThresholdAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.112 - acAMSProcedureResult
1.3.6.1.4.1.5003.9.10.1.21.2.0.54 - acASRThresholdAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.111 - acAWSSecurityRoleAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.139 - acActiveAlarmTableOverflow
1.3.6.1.4.1.5003.9.10.1.21.2.0.12 - acActivityLog
1.3.6.1.4.1.5003.9.10.1.21.2.0.105 - acAnalogLineLeftOffhookAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.141 - acAnalogPortGroundFaultOutOfService
1.3.6.1.4.1.5003.9.10.1.21.2.0.76 - acAnalogPortHighTemperature
1.3.6.1.4.1.5003.9.10.1.21.2.0.47 - acAnalogPortSPIOutOfService
1.3.6.1.4.1.5003.9.10.1.21.2.0.46 - acAtmPortAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.13 - acAudioProvisioningAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.14 - acBChannelAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.85 - acBoardCallResourcesAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.8 - acBoardConfigurationError
1.3.6.1.4.1.5003.9.10.1.21.2.0.2 - acBoardControllerFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.9 - acBoardEthernetLinkAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.10 - acBoardEvBoardStarted
1.3.6.1.4.1.5003.9.10.1.21.2.0.4 - acBoardEvResettingBoard
1.3.6.1.4.1.5003.9.10.1.21.2.0.5 - acBoardFatalError
1.3.6.1.4.1.5003.9.10.1.21.2.0.1 - acBoardOverloadAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.11 - acBoardSignalingCpuUsageThresholdAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.103 - acBoardTemperatureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.3 - acBoardWanLinkAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.79 - acCDRServerAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.142 - acCertificateExpiryAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.128 - acCertificateExpiryNotification
1.3.6.1.4.1.5003.9.10.1.21.2.0.92 - acClockConfigurationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.149 - acCloudLicenseManagerAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.132 - acClusterBandwidthAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.126 - acDChannelStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.37 - acDS3AISAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.67 - acDS3LOFAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.68 - acDS3LOSAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.69 - acDS3RAIAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.66 - acDSPFarmsMismatchAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.143 - acDataInterfaceStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.83 - acDebugRecordingActivationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.150 - acDialPlanFileReplaced
1.3.6.1.4.1.5003.9.10.1.21.2.0.45 - acDspOperationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.153 - acEnhancedBITStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.18 - acEthernetGroupAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.86 - acFanTrayAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.29 - acFaultyDSPAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.152 - acFeatureKeyError
1.3.6.1.4.1.5003.9.10.1.21.2.0.6 - acFlexLicenseManagerAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.144 - acFloatingLicenseAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.138 - acGWSASEmergencyModeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.59 - acH248LostConnectionWithCA
1.3.6.1.4.1.5003.9.10.1.21.2.0.44 - acHAEthernetGroupAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.137 - acHANetworkMismatchAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.135 - acHANetworkMonitorAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.136 - acHANetworkWatchdogStatusAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.98 - acHASystemConfigMismatchAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.34 - acHASystemFaultAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.33 - acHASystemSwitchOverAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.35 - acHTTPDownloadResult
1.3.6.1.4.1.5003.9.10.1.21.2.0.28 - acHTTPProxyServiceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.108 - acHitlessUpdateStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.48 - acHwFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.43 - acIDSBlacklistNotification
1.3.6.1.4.1.5003.9.10.1.21.2.0.101 - acIDSPolicyAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.99 - acIDSThresholdCrossNotification
1.3.6.1.4.1.5003.9.10.1.21.2.0.100 - acIPv4ErrorAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.158 - acIPv6ErrorAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.53 - acInstallationFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.140 - acIpGroupNoRouteAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.114 - acKeepAlive
1.3.6.1.4.1.5003.9.10.1.21.2.0.16 - acKpiThresholdCrossing
1.3.6.1.4.1.5003.9.10.1.21.2.0.148 - acLDAPLostConnection
1.3.6.1.4.1.5003.9.10.1.21.2.0.75 - acLicenseKeyHitlessUpgradeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.129 - acLicensePoolApplicationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.107 - acLicensePoolExpirationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.127 - acLicensePoolInfraAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.106 - acLicensePoolOverAllocationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.125 - acMCNotSecuredAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.151 - acMediaClusterAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.133 - acMediaClusterRemoteInterfaceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.134 - acMediaProcessOverloadAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.81 - acMediaRealmBWThresholdAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.87 - acMeteringAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.146 - acModuleOperationAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.123 - acModuleServiceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.122 - acMtceHwFanTrayFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.119 - acMtceHwTemperatureFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.118 - acMtceNetworkFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.116 - acMtcePsuFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.120 - acMtceSwUpgradeFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.117 - acMtcmClusterHaAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.115 - acNATTraversalAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.17 - acNERThresholdAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.113 - acNFASGroupAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.84 - acNGINXConfigurationIsInvalidAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.130 - acNGINXPprocessIsNotRunningAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.131 - acNTPServerStatusAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.71 - acNoReplyFromDNSServerAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.155 - acNqmConnectivityAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.88 - acNqmCqMosAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.95 - acNqmJitterAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.90 - acNqmLqMosAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.96 - acNqmPacketLossAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.91 - acNqmRttAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.89 - acOCSPServerStatusAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.78 - acOperationalStateChange
1.3.6.1.4.1.5003.9.10.1.21.2.0.15 - acPEMAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.31 - acPerformanceMonitoringThresholdCrossing
1.3.6.1.4.1.5003.9.10.1.21.2.0.27 - acPortServiceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.124 - acPowerOverEthernetStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.80 - acPowerSupplyAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.30 - acProxyConnectionLost
1.3.6.1.4.1.5003.9.10.1.21.2.0.94 - acProxyConnectivity
1.3.6.1.4.1.5003.9.10.1.21.2.0.102 - acRedundantBoardAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.97 - acRemoteMonitoringAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.145 - acReservedAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.109 - acResetNeededAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.110 - acSAMissingAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.32 - acSDRServerAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.147 - acSS7AliasPcStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.73 - acSS7LinkBlockStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.21 - acSS7LinkCongestionStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.22 - acSS7LinkInhibitStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.20 - acSS7LinkSetStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.23 - acSS7LinkStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.19 - acSS7RedundancyAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.26 - acSS7RouteSetStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.24 - acSS7SNSetStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.25 - acSS7UalGroupStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.74 - acSSHConnectionStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.77 - acSWUpgradeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.70 - acSonetIfHwFailureAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.42 - acSonetLineAISAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.40 - acSonetLineRDIAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.41 - acSonetPathSTSAISAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.62 - acSonetPathSTSLOPAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.61 - acSonetPathSTSRDIAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.63 - acSonetPathSignalLabelMismatchAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.65 - acSonetPathUnequippedAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.64 - acSonetSectionLOFAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.38 - acSonetSectionLOSAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.39 - acTLSCertificateMismatchAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.154 - acTLSSocketsLimitAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.159 - acTMInconsistentRemoteAndLocalPLLStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.56 - acTMReferenceChange
1.3.6.1.4.1.5003.9.10.1.21.2.0.58 - acTMReferenceStatus
1.3.6.1.4.1.5003.9.10.1.21.2.0.57 - acThreeWayConferenceOutOfResources
1.3.6.1.4.1.5003.9.10.1.21.2.0.72 - acTrackIdStateChangeAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.121 - acTrunksAlarmFarEndLOF
1.3.6.1.4.1.5003.9.10.1.21.2.0.52 - acTrunksAlarmNearEndLOF
1.3.6.1.4.1.5003.9.10.1.21.2.0.50 - acTrunksAlarmNearEndLOS
1.3.6.1.4.1.5003.9.10.1.21.2.0.49 - acTrunksAlarmRcvAIS
1.3.6.1.4.1.5003.9.10.1.21.2.0.51 - acUserInputAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.36 - acV52InterfaceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.60 - acVMMaintenaceAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.157 - acWEBUserAccessDisabled
1.3.6.1.4.1.5003.9.10.1.21.2.0.93 - acWeakPasswordAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.156 - acWeakRedundancy
1.3.6.1.4.1.5003.9.10.1.21.2.0.55 - acWirelessCellularModemAlarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.82 - acWirelessCellularModemStatusChanged
1.3.6.1.4.1.5003.9.10.1.21.2.0.104 - acgwAdminStateChange
1.3.6.1.4.1.5003.9.10.1.21.2.0.7