MIB Browser

ARUBA-TC

Arubaos
Objects
0
Source
Show full MIB
snmptranslate -m ARUBA-TC -Tp

Imports

SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, ObjectSyntax, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

The site cannot show an OID tree for this MIB. Use Show full MIB to read the MIB file.

Textual conventions

ArubaACLAction INTEGER

deny(1) dstNAT(4) permit(2) redirect(5) srcNAT(3)

Represents the Actions in an ACL rule.
ArubaACLDomain INTEGER

alias(1) any(2) host(4) network(5) user(3)

Represents both the source and destination to which an ACL rule will
be applied.
ArubaACLNetworkServiceType INTEGER

alias(1) any(2) protocol(5) tcp(3) udp(4)

Represents the network service in an ACL Rule.
ArubaAPConductorStatus INTEGER

down(2) move(3) up(1)

AP status as seen by the conductor controller
(used to indicate a status change).
ArubaAPDot1dState INTEGER

blocking(7) disabled(3) forwarding(6) learning(5) listening(4) notAvailable(1) off(2)

Represents the AP port spanning tree state.
ArubaAPMasterStatus INTEGER

down(2) move(3) up(1)

AP status as seen by the master controller
      (used to indicate a status change).
      **NOTE: this textual convention is obsoleted and replaced by
      ArubaAPConductorStatus.
ArubaAPMatchMethod INTEGER

exactMatch(1) minusOneMatch(3) notApplicable(0) ouiMatch(4) plusOneMatch(2)

Represents the match method of a suspected rogue AP.
ArubaAPMatchType INTEGER

apBSSID(10) apRule(12) apWiredMac(3) baseBSSIDOverride(6) classificationDisabled(9) configuredWiredMac(1) ethernetGatewayWiredMac(8) ethernetWiredMac(2) externalWiredMac(4) manual(5) mms(7) propagatedEthernetWiredMac(11) systemGatewayMac(14) systemWiredMac(13) unknown(0)

Represents the match type of a suspected rogue AP.
ArubaAPStatus INTEGER

down(2) up(1)

The status of the access point.
ArubaAPUplinkChangeReason INTEGER

linkFailure(1) preemption(3) vpnFailure(2)

Used to specify the reason for AP uplink change.

linkFailure - The uplink went down
vpnFailure  - VPN tunnel could not be sustained using the uplink
preemption  - The uplink was pre-empted by a higher-priority uplink
ArubaAPUplinkType INTEGER

ethernet(1) pppoe(3) usb(2) wifi(4)

AP uplink type
ArubaARMChangeReason INTEGER

airmatchFreeze(23) airmatchInit(26) airmatchNoise(21) airmatchNoiseCleared(28) airmatchRogueCont(29) airmatchSolver(22) airmatchUnfreeze(24) armChannelQualityThresh(18) armDecreasePower(14) armDynamicBW(19) armEmptyCh(12) armErrorThresh(10) armIncreasePower(15) armInterference(8) armInterferenceCCA(20) armInvalidCh(9) armNoiseThresh(11) armRogueCont(13) armTurnOffRadio(16) armTurnOnRadio(17) cancel40mhzIntol(6) fortyMhzAlign(7) fortyMhzIntol(5) radarCleared(2) radarDetected(1) random(25) txHang(3) txHangClear(4) unknown(27)

The reason for ARM or AirMatch based change.
ArubaAccessPointMode INTEGER

accessPoint(2) accessPointAndMonitor(3) airMonitor(1) airmatchMonitor(12) amsMode(10) controllerMode(11) meshPoint(5) meshPortal(4) rfprotectSensor(6) spectrumSensor(7) station(8) stationMeshP(9)

The mode of the access point.
ArubaActiveState INTEGER

active(1) inactive(2)

Represents if a feature is active or inactive.
ArubaAddressType INTEGER

bssid(3) dstAddress(2) srcAddress(1)

Address Type.
ArubaAntennaSetting INTEGER

disabled(3) enabled(2) notPresent(1)

Represents the status of the external antenna.
ArubaAuthServerType INTEGER

internaldb(1) kerberos(4) ldap(3) radius(2) tacacs(5)

The type of the auth server.
ArubaAuthenticationMethods INTEGER

dot1x(4) kerberos(5) mac(2) none(0) other(255) pubcookie(15) secureId(7) via-vpn(28) vpn(3) web(1) xSec(16) xSecMachine(17)

Authentication Method.
ArubaBlackListReason INTEGER

authFailure(3) esiBlacklist(9) ipSpoofing(8) mitmAttack(2) other(100) pingFlood(4) sessionBlacklist(7) sessionFlood(5) synFlood(6) userDefined(1)

Black List Reason.
**NOTE: this textual convention is obsoleted and replaced by
ArubaDenyListReason.
ArubaCallStates INTEGER

aborted(14) alerting(6) blocked(15) blockwait(11) cancelling(8) challenging(9) connected(4) connecting(2) delivered(3) fail(13) idle(0) initiated(1) offered(5) releasing(7) succ(12) transient(10)

The Call state.
ArubaCardType INTEGER

lc1(1) lc2(2) m3mk1(8) reserved1(14) reserved2(15) sc1(3) sc2(4) sw1500(22) sw200(7) sw2400(5) sw2500(21) sw3200(9) sw3400(10) sw3500(20) sw3600(11) sw620(16) sw650(12) sw651(13) sw7005(24) sw7010(23) sw7024(27) sw7024xm(28) sw7030(25) sw7205(26) sw7210(17) sw7220(18) sw7240(19) sw800(6)

Type of the hardware module.
ArubaConfigurationChangeType INTEGER

create(1) delete(2) modify(3)

Configuration Change Types.
ArubaConfigurationState INTEGER

error(2) success(1)

Configuration Transfer Types.
ArubaDBType INTEGER

mssql(1) mysql(2)

DataBase Type.
ArubaDaysOfWeek INTEGER

fri(6) mon(2) sat(7) sun(1) thu(5) tue(3) wed(4)

Represents the Actions in an ACL rule.
ArubaDenyListReason INTEGER

authFailure(3) esiDenylist(9) ipSpoofing(8) mitmAttack(2) other(100) pingFlood(4) sessionDenylist(7) sessionFlood(5) synFlood(6) userDefined(1)

Deny List Reason.
ArubaDot1dState INTEGER

blocked(2) disabled(1) forwarding(5) learning(4) listening(3)

Represents the controller port spanning tree state.
ArubaDot3azStatus Bits

disabled(0) eee1000BaseKX(5) eee1000BaseT(3) eee100BaseTX(2) eee10GBaseKR(7) eee10GBaseKX4(6) eee10GBaseT(4) unsupported(1)

Represents the state of Energy Efficient Ethernet (802.3az).
ArubaDot3bzStatus INTEGER

no(1) unsupported(0) yes(2)

Represents the state of 802.3bz.
ArubaDual5GMode INTEGER

disabled(0) enabled(1) notApplicable(3) unknown(2)

Dual 5GHz Operating Mode
ArubaESIServerMode INTEGER

bridged(1) nat(3) routed(2)

The mode of the ESI server.
ArubaESIServerStatus INTEGER

down(2) up(1)

The status of the ESI server.
ArubaEnableValue INTEGER

disabled(2) enabled(1)

Represents a Flag which is either Enabled or Disabled.
ArubaEncryptionMethods Bits

bSec-128(13) bSec-256(14) disabled(0) dynamic-wep(2) dynamic-wpa(4) mpsk-aes(21) owe-aes(16) static-wep(1) static-wpa(3) wpa-aes(10) wpa-psk-aes(9) wpa2-8021x-aes(6) wpa2-8021x-tkip(12) wpa2-psk-aes(5) wpa2-psk-tkip(11) wpa2PreAuth(7) wpa3-aes-ccm-128(19) wpa3-aes-gcm-256(22) wpa3-cnsa(18) wpa3-sae-aes(17) xsec(8)

Encryption Methods.
ArubaEncryptionType INTEGER

aes-128-cmac(14) bSec-128(12) bSec-256(13) dynamic-wep(2) ft-8021x(17) ft-psk(16) none(0) owe-aes(20) static-wep(1) unknown(15) wpa-aes(6) wpa-psk-aes(5) wpa-psk-tkip(3) wpa-tkip(4) wpa2-aes(10) wpa2-psk-aes(9) wpa2-psk-tkip(7) wpa2-tkip(8) wpa3-aes-ccm-128(23) wpa3-aes-gcmp-256(22) wpa3-cnsa(18) wpa3-sae-aes(21) xSec(11)

Encryption Type.
ArubaEnet1Mode INTEGER

activeStandby(1) bridge(3) notApplicable(4) split(5) tunnel(2)

Represents the Mode of the Ethernet port on the Access Point
ArubaFlexRadioMode INTEGER

dual2GHzplus5GHzBand(2) notApplicable(4) single2GHzBand(0) single5GHzBand(1) unknown(3)

Flex Radio Operating Mode
ArubaFrameType INTEGER

associateRequest(0) associateResponse(1) atim(9) auth(11) beacon(8) deauth(12) disassociate(10) probeRequest(4) probeResponse(5) reassociateRequest(2) reassociateResponse(3)

Represents the Frame type.
ArubaHTExtChannel INTEGER

above(2) below(3) eighty(4) eightyPlusEighty(6) none(1) onesixty(5)

Represents the extension channel offset relative to the current channel.
ArubaHTMode INTEGER

he160(12) he20(9) he40(10) he80(11) he80plus80(13) ht20(2) ht40(3) none(1) vht160(7) vht20(4) vht40(5) vht80(6) vht80plus80(8)

Represents the HT status of the access point or client.
ArubaHTRate INTEGER

ht104(20) ht108(21) ht117(22) ht120(23) ht121dot5(24) ht13(2) ht130(25) ht135(26) ht13dot5(3) ht15(4) ht150(27) ht162(28) ht180(29) ht19dot5(5) ht216(30) ht240(31) ht243(32) ht26(6) ht27(7) ht270(33) ht30(8) ht300(34) ht39(9) ht40dot5(10) ht45(11) ht52(12) ht54(13) ht58dot5(14) ht60(15) ht65(16) ht6dot5(1) ht78(17) ht81(18) ht90(19) unknown(0)

Represents HT rate
ArubaHaConnectivityStatus INTEGER

haApDenied(4) haCpUnreach(2) haHbtFailure(5) haImageMissMatch(3) haInvalidHelloResponse(6) haNetUnreach(1) haStandbyTunnelDown(7) haSuccess(0)

Represents the HA standby connectivity status of the Access Point
ArubaHaRole INTEGER

active(1) disabled(3) dual(0) standby(2)

Represents the HA role of the Aruba controller
ArubaHashAlgorithms INTEGER

md5(1) sha(2)

Represents the Actions in an ACL rule.
ArubaIfState INTEGER

linkDown(2) linkUp(1)

Used to specify the state of an interface.

linkUp   - Operational state of this interface is up.
linkDown - Operational state of this interface is down.
ArubaIfStateChangeReason INTEGER

admin(1) bpduGuard(5) loopProtect(2) macLimit(3) raGuard(4)

Used to specify the reason for interface state change.

admin       - User has explicitly issued 'shutdown' or 'no shutdown'
              configuration from CLI on this interface.
loopProtect - If ifState of an interface changes to linkDown, then
              it is used to specify that a loop has been detected on
              this interface by loop protect mechanism.
              If ifState of an interface changes to linkUp, then
              it is used to specify that loop-protect error has been
              cleared out on this interface through port auto-recovery
              mechanism or through explicit clear error-recovery
              command.
macLimit    - If ifState of an interface changes to linkDown, then
              it is used to specify that number of learnt MACs on this
              interface exceeds the limit configured.
              If ifState of an interface changes to linkUp, then it is
              used to specify that mac-limit error has been cleared out
              on this interface through port auto-recovery mechanism or
              through explicit clear error-recovery command.
raGuard     - If ifState of an interface changes to linkDown, then it
              is used to specify that invalid router advertisement has
              been identified on this interface, resulting shutting
              down of this interface.
              If ifState of an interface changes to linkUp, then it is
              used to specify that raGuard error has been cleared out on
              this interface through port auto-recovery mechanism or
              through explicit clear error-recovery command.
bpduGuard   - If ifState of an interface changes to linkDown, then it
              is used to specify that BPDU is received on this interface
              resulting shutting down of this interface.
              If ifState of an interface changes to linkUp, then it is
              used to specify that BPDU Guard error has been cleared out
              on this interface through port auto-recovery mechanism or
              through explicit clear error-recovery command.
ArubaIfType INTEGER

loopback(4) port(1) tunnel(3) vlan(2)

The type of interface referred to by the value of ifIndex.
ArubaMeshRole INTEGER

nonmesh(0) point(1) portal(2)

Mesh role
ArubaMonAuthAlgorithm INTEGER

dot1x(2) dot1x256(5) ftdot1x(3) ftpsk(4) ftsae(9) none(0) other(10) owe(12) psk(1) psk256(6) sae(8) suiteb(11) tdls(7)

Represents the WPA authentication algorithm supported by the access point.
ArubaMonEncryptionCipher INTEGER

aesccmp(4) gcm256(6) none(0) other(5) tkip(3) wep104(2) wep40(1)

Represents the WPA encryption cipher supported by the access point.
ArubaMonEncryptionType INTEGER

open(0) wep(1) wpa(2) wpa2(3) wpa3(4)

Represents the encryption type supported by the access point.
ArubaMonitorMode INTEGER

all(1) mixed(3) none(2) unknown(0)

Represents whether the AP has any radios dedicated to monitoring.
ArubaOperStateValue INTEGER

down(2) testing(3) up(1)

Represents Operational state of an interface.
ArubaPhyType INTEGER

dot11a(1) dot11ag(4) dot11ax6ghz(6) dot11b(2) dot11g(3) wired(5)

Represents the PHY-type of the access point or client.  Wired clients will
show 'wired' in user MIB entries.
ArubaPoeState INTEGER

disabled(1) enabled(2) enabledCisco(3) notAvailable(4)

Represents the POE mode.
ArubaPortDuplex INTEGER

auto(3) full(2) half(1)

Port Duplexity.
ArubaPortMode INTEGER

access(1) dot1q(2)

Represents the controller port mode.
ArubaPortSpeed INTEGER

speed1000Mbps(3) speed100Mbps(2) speed10Gbps(5) speed10Mbps(1) speed2Point5Gbps(6) speed40Gbps(8) speed5Gbps(7) speedAuto(4)

Port Speed.
ArubaPortType INTEGER

fastethernet(1) fivegigabitethernet(5) gigabitethernet(2) twogigabitethernet(4) xgigabitethernet(3)

Port Type.
ArubaPortalServerDownReason INTEGER

connectFail(1)

Used to specify the reason for Portal server down.

connectFail - Connect Portal server fail
ArubaRogueApType INTEGER

dos(4) interfering(2) knownInterfering(6) suspectedUnsecure(7) unknown(5) unsecure(3) valid(1)

Represents the Rogue AP Type.
ArubaSplit5GMode INTEGER

disabled(0) enabled(1) notApplicable(3) unknown(2)

Split 5GHz Operating Mode
ArubaStackChangeEvent INTEGER

lineCardSlotChanged(4) other(1) primarySlotChanged(2) priorityChanged(6) roleChanged(5) secondarySlotChanged(3) slotExceeded(8) versionMismatch(7)

Used to specify the event which caused change in topology in stack.
ArubaStackIfTopoJoined INTEGER

connected(1) disconnected(2)

Used to specify whether an interface has joined the stacking
topology or left the topology.
ArubaStackState INTEGER

away(4) linecard(3) primary(1) secondary(2)

The state of the stack element in the stack.

primary   - the stack element is in primary state.
secondary - the stack element is in secondary state.
linecard  - the stack element is in linecard state.
away      - the stack element is in inactive state.

primary, secondary and linecard implies active state of the stack
element.
ArubaStationType INTEGER

dos(3) interfering(2) unknown(0) valid(1)

Represents the station type.
ArubaSubAuthenticationMethods INTEGER

authCHAP(2) authMSCHAP(3) authMSCHAPv2(4) authPAP(1) eapLEAP(7) eapMD5(8) eapPEAP(9) eapTLS(5) eapTTLS(6)

Sub Authentication Method (e.g. EAP type).
ArubaSupportStatus INTEGER

supported(2) unsupported(1)

Represents if a feature is supported or unsupported.
ArubaSwitchRole INTEGER

backupconductor(3) conductor(1) local(2) standalone(4)

Represents the role of the controller
ArubaThresholdResourceType INTEGER

controlPathCpu(1) controlPathMemory(2) dataPathCpu(0) noofAps(5) noofLocals(6) noofVaps(7) totalTunnelCapacity(3) userCapacity(4)

Represents the Threshold Resource Types
ArubaUnprovisionedStatus INTEGER

no(2) yes(1)

Represents whether the AP is provisioned or not.
ArubaUserForwardMode INTEGER

bridge(1) split-tunnel(3) tunnel-decrypted(2) tunnel-encrypted(0)

User Forwarding Mode.
ArubaVlanValidRange INTEGER (1..4095)
Represents the Valid Vlan Id Range.
ArubaVoiceCacBit Bits

cacActiveLoadBalancing(0) cacHandRsrvThresholdReached(2) cacHighCapThresholdReached(1) cacPeakCapacityReached(3)

Voice CAC bit flags
ArubaVoiceCdrDirection INTEGER

ic(1) og(0)

VoIP CDR direction
ArubaVoipProtocol INTEGER

h323(13) sccp(1) sip(9) svp(2) ua(11) vocera(3)

VoIP protocol used
ArubaVoipProtocolType INTEGER

h323(13) sccp(1) sip(9) svp(2) ua(11) unknown(15) vocera(3)

The type of VoIP protocols supported.
ArubaVoipRegState INTEGER

challenge(3) registered(4) registering(1) unknown(0) unregistered(5) unregistering(2)

VoIP registered state
ArubaVrrpState INTEGER

backup(2) initialize(1) master(3)

DataBase Type.
InterfaceIndex Integer32 (1..2147483647)
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system.  It is
recommended that values are assigned contiguously starting
from 1.  The value for each interface sub-layer must remain
constant at least from one re-initialization of the entity's
network management system to the next re-initialization.

Used by