MIB Browser

CADANT-TC

Cadant Inc.
This MIB module contains the textual conventions that are shared
among multiple ARRIS MIBs.
Organization
Arris International Inc
Root OID
1.3.6.1.4.1.4998.0
Last updated
Objects
1
Source
Show full MIB
snmptranslate -m CADANT-TC -Tp
snmpwalk -v2c -c <community> -m CADANT-TC <host> 1.3.6.1.4.1.4998.0

Imports

CADANT-PRODUCTS-MIBcadant
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Counter64, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

OID tree

NameOIDTypeAccessStatus
IcadTextualConventions1.3.6.1.4.1.4998.0

Textual conventions

AAAmethod INTEGER

group(5) line(2) local(4) none(1)

This TEXTUAL-CONVENTION describes the type of AAA
methods available on the C4.
AccountingType INTEGER

start-stop(1) stop-only(2)

This TEXTUAL-CONVENTION describes the different types of accounting services.
AdminState INTEGER

down(2) up(1)

The administrative or the desired states of the element and are set by the EMS.
CadAclString OCTET STRING (SIZE (0..32))
The name of the ACL this ACE is part of.
CadAclType INTEGER

ext-access-list(2) ipv6-access-list(5) none(0) rate-limit-access-list(3) remark(4) std-access-list(1)

The type of ACL this ACE is part of.
CadBridgeGroupId Integer32 (33..255)
Uniquely identifies the bridge group.
CadBridgePortType INTEGER

any(4) cm(1) cpeauth(2) cpeunauth(3) none(5)

Type of traffic allowed on a bridge port.
Ethernet ports allow any type of traffic.
RF ports can be sub divided for CM traffic,
authorized CPE traffic, and unauthorized CPE
traffic.
CadCpeDeviceTypes Bits

cable-modem(0) cpe(1) dva(7) erouter(6) mta(3) ps(2) reserved10(10) reserved11(11) reserved12(12) reserved13(13) reserved14(14) reserved15(15) reserved16(16) reserved17(17) reserved18(18) reserved19(19) reserved20(20) reserved21(21) reserved22(22) reserved23(23) reserved24(24) reserved25(25) reserved26(26) reserved27(27) reserved28(28) reserved29(29) reserved30(30) reserved31(31) reserved9(9) sg(8) stb(4) tea(5)

CPE Device types.
CadDouble Counter64

Display hint: d-10

This type is used to express and display 64-bit, double-precision
floating-point values.
CadExtAclCondition INTEGER

eq(1) ge(6) gt(5) le(4) lt(3) na(0) ne(2) range(7)

This TEXTUAL-CONVENTION describes the condition of Extended ACLs.
CadIfDirection INTEGER

in(1) out(2)

A direction of flow on an interface.
CadIpPort INTEGER (0..65535 | -1)
The port of an IP packet.
The value -1 indicates that this field is not used.
CadIpTos INTEGER (0..254)
The type-of-service of an IP packet.
The value 0 indicates that this field is not used.
CadIpTosMask INTEGER (0 | 30 | 224 | 254)
The allowed type-of-service mask of an IP packet. 30 is used
when the 4 bit TOS is specified.  224 is used when the 3 bit
precedence is specified, and 254 is used when the entire 7
bit TOS is specified.  A value of 0 indicates that the TOS field
is not used.
CadProtocolType INTEGER (0..255 | -1)
The protocol type an IP packet (8 bits). 0 is IP, 1 is ICMP,
2 is IGMP, 6 is TCP 17 is UDP.  See RFC-1700 for complete list.
The value -1 indicates an invalid/unused protocol type.
CadTcpFlags Bits

ack(1) fin(5) push(2) rst(3) syn(4) urg(0)

The values available in the flags portion of the TCP header.
CardId Integer32 (1..99)
Uniquely identifies the individual Circuit Pack.
Number of 99 indicates an invalid CardId.
CardSubId Integer32 (0..1)
Uniquely identifies an entity on the circuit pack.
CardSubType INTEGER

dcard0d12u(35) dcard1d8u(20) dcard2d8u(21) dcardiu1d8u(1) dcardiu2d12u(23) dcardiu2d8u(22) discdriveA(13) discdriveB(14) dmm16m(37) dmm16m16p4iu(36) ecard1gig(34) ecard1oc12(33) ecard4e(2) ecard4oc3(31) ecard7oc3(32) ecard8e(30) fanA(7) fanB(8) fanC(9) fanD(10) fcard(3) invalid(99) mcard(4) powerA(11) powerB(12) rcard(6) rcardhcp(40) unknown(98)

Enumeration of more specific current Card Type.
For cards with only one subtype, the type and subtype
should be identical.
CardType INTEGER

dcard(1) discdriveA(13) discdriveB(14) dmm(15) ecard(2) fanA(7) fanB(8) fanC(9) fanD(10) fcard(3) invalid(99) mcard(4) powerA(11) powerB(12) rcard(6) unknown(98)

Enumeration of generic Card Type.
DiskVolumeUsageLevel INTEGER

critical(4) major(3) minor(2) normal(1)

Describe the disk volume usage level
DuplexStatus INTEGER

active(1) notapplicable(0) protected(4) simplex(3) standby(2)

not applicable to all components
EqActionType INTEGER

cardreset(7) initialize(1) notapplicable(0) remove(3) restorecond(4) restoreuncd(5) switch(2) systemreset(6)

not applicable to all components
FirmwareSource INTEGER

boot1(3) boot2(4) committed(1) transient(2) unknown(5)

This type describes the initial source of the firmware running on
a card.  Committed and transient indicate the card flash device and
the downloaded image, respectively.  Boot1 and Boot2 indicate which
of the resident boot images was used to boot the card.
FlowActivityState INTEGER

greedy(3) needy(1) normal(2)

Flow Activity State describes the recent bandwidth utilization history
of a service flow relative to its Service Level Agreement. A flow that is
operating below its Tmin is said to be 'needy'. A flow that is operating
above Tmin but below Tmid is said to be 'normal'. A flow that is operating
above Tmid but below Tmax is said to be 'greedy'.
FlowControlMode INTEGER

desired(3) invalid(99) off(2) on(1) unknown(98)

flow control settings for a network port.
InetAddressIPv4or6 OCTET STRING (SIZE (0 | 4 | 8 | 16 | 20))
This TEXTUAL-CONVENTION is similar to InetAddress as defined
in the INET-ADDRESS-MIB. However, InetAddressIPv4or6 does not
allow DNS addresses and its address type, either IPv4 or IPv6,
can be readily determined from its length alone. If the
address is an IPv4 address, then the length will be exactly
4 bytes. If the address is an IPv6 address, then the length
will be either 16 or 20 bytes.

If the length if 0, then the address is empty or null.

If the length is 4:
  octets   contents         encoding
   1-4     IP address       network-byte order

If the length is 8:
  octets   contents         encoding
   1-8     EUI IPv6 address network-byte order

If the length is 16:
  octets   contents         encoding
   1-16    IPv6 address     network-byte order

If the length is 20:
  octets   contents         encoding
   1-16    IPv6 address     network-byte order
  17-20    scope identifier network-byte order

The scope identifier (bytes 17-20) MUST NOT be present
for global IPv6 addresses. For non-global IPv6 addresses
(e.g. link-local or site-local addresses), the scope
identifier MUST always be present. It contains a link
identifier for link-local and a site identifier for
site-local IPv6 addresses.

The scope identifier MUST disambiguate identical address
values. For link-local addresses, the scope identifier will
typically be the interface index (ifIndex as defined in the
IF-MIB, RFC 2233) of the interface on which the address is
configured.

The scope identifier may contain the special value 0
which refers to the default scope. The default scope
may be used in cases where the valid scope identifier
is not known (e.g., a management application needs to
write a site-local InetAddressIPv6 address without
knowing the site identifier value). The default scope
SHOULD NOT be used as an easy way out in cases where
the scope identifier for a non-global IPv6 is known.
LineType INTEGER

console(1) vty(2)

This TEXTUAL-CONVENTION describes the type line connections
available on the C4.
MacChlPortType INTEGER

dport(1) invalid(99) uchannel(8)

Enumeration of current Port Type.
MacPortId Integer32 (1..448)
A valid unique identifier for a MAC port in a C4 CMTS system.
MacPortIdWithInvalid Integer32 (1..449)
Identifier for a MAC port in a C4 CMTS system.
OUIAddress OCTET STRING (SIZE (3))

Display hint: 1x:

Represents the first three(3), most significant bytes of
an 802 MAC address represented in the `canonical' order
defined by IEEE 802.1a, i.e., as if it were transmitted
least significant bit first, even though 802.5 (in contrast
to other 802.x protocols) requires MAC addresses to be
transmitted most significant bit first.
OverloadStatus INTEGER

normal(1) red(3) yellow(2)

Three levels indicating how much work the card is doing.
PicType INTEGER

cam16d(14) cam16dspare(15) cameven(1) camevensp1to1(2) camevensp2to1(3) camevensp4to1(4) camevensp8to1(5) camodd(6) camoddsp1to1(7) camoddsp2to1(8) camoddsp4to1(9) camoddsp8to1(10) camspare(11) invalid(99) nam(12) scm(13) unknown(98)

This type describes the PIC attached to the backplane behind a a card.
PortDetectedMode INTEGER

fullDuplex100Mpbs(2) fullDuplex10Mpbs(4) halfDuplex100Mpbs(3) halfDuplex10Mpbs(5) invalid(99) sfpFullDuplex1000BaseCWDM(20) sfpFullDuplex1000BaseDWDM(21) sfpFullDuplex1000BaseLH(17) sfpFullDuplex1000BaseLX(16) sfpFullDuplex1000BaseLXLH(18) sfpFullDuplex1000BaseSX(15) sfpFullDuplex1000BaseT(9) sfpFullDuplex1000BaseZX(19) sfpFullDuplex100BaseT(11) sfpFullDuplex10BaseT(13) sfpHalfDuplex1000BaseT(10) sfpHalfDuplex100BaseT(12) sfpHalfDuplex10BaseT(14) unknown(98) xfpFullDuplex10GBaseER(25) xfpFullDuplex10GBaseLR(24) xfpFullDuplex10GBaseLRM(23) xfpFullDuplex10GBaseLX4(27) xfpFullDuplex10GBaseSR(22) xfpFullDuplex10GBaseZR(26)

detected mode settings for a network port.
PortId Integer32 (1..99)
Uniquely identifies the port. Number of 99 indicates an invalid PortId.
PortMode INTEGER

autoNegotiate(1) fullDuplex10000Mpbs(8) fullDuplex1000Mpbs(6) fullDuplex100Mpbs(2) fullDuplex10Mpbs(4) halfDuplex1000Mpbs(7) halfDuplex100Mpbs(3) halfDuplex10Mpbs(5) invalid(99)

mode settings for a network port.
PortType INTEGER

dport(1) dportMac(10) eport10000BaseT(9) eport1000BaseT(7) eport100BaseT(4) eport10BaseT(3) invalid(99) macport(5) mport(6) uchannel(8) uport(2)

Enumeration of current Port Type.
PrimaryState INTEGER

is(1) oos(2)

The operational state
IS(1): The element is operable and available for use
OOS(2): The element/resource is inoperable and unable to provide service
UNEQ(3): The element/resource is unequiped.
SchedDay Bits

d1(0) d10(9) d11(10) d12(11) d13(12) d14(13) d15(14) d16(15) d17(16) d18(17) d19(18) d2(1) d20(19) d21(20) d22(21) d23(22) d24(23) d25(24) d26(25) d27(26) d28(27) d29(28) d3(2) d30(29) d31(30) d4(3) d5(4) d6(5) d7(6) d8(7) d9(8) r1(31) r10(40) r11(41) r12(42) r13(43) r14(44) r15(45) r16(46) r17(47) r18(48) r19(49) r2(32) r20(50) r21(51) r22(52) r23(53) r24(54) r25(55) r26(56) r27(57) r28(58) r29(59) r3(33) r30(60) r31(61) r4(34) r5(35) r6(36) r7(37) r8(38) r9(39)

The set of days in a month on which a scheduled action
should take place.  There are two sets of bits one can
use to define the day within a month:

Enumerations starting with the letter 'd' indicate a
day in a month relative to the first day of a month.
The first day of the month can therefore be specified
by setting the bit d1(0) and d31(30) means the last
day of a month with 31 days.

Enumerations starting with the letter 'r' indicate a
day in a month in reverse order, relative to the last
day of a month.  The last day in the month can therefore
be specified by setting the bit r1(31) and r31(61) means
the first day of a month with 31 days.

Setting multiple bits will include several days in the set
of possible days for this schedule.  Setting all bits will
cause the scheduler to ignore the day within a month.

Setting all bits starting with the letter 'd' or the
letter 'r' will also cause the scheduler to ignore the
day within a month.
SchedHour Bits

h0(0) h1(1) h10(10) h11(11) h12(12) h13(13) h14(14) h15(15) h16(16) h17(17) h18(18) h19(19) h2(2) h20(20) h21(21) h22(22) h23(23) h3(3) h4(4) h5(5) h6(6) h7(7) h8(8) h9(9)

The set of hours within a day during which the scheduled
action should take place.
SchedMinute Bits

m0(0) m1(1) m10(10) m11(11) m12(12) m13(13) m14(14) m15(15) m16(16) m17(17) m18(18) m19(19) m2(2) m20(20) m21(21) m22(22) m23(23) m24(24) m25(25) m26(26) m27(27) m28(28) m29(29) m3(3) m30(30) m31(31) m32(32) m33(33) m34(34) m35(35) m36(36) m37(37) m38(38) m39(39) m4(4) m40(40) m41(41) m42(42) m43(43) m44(44) m45(45) m46(46) m47(47) m48(48) m49(49) m5(5) m50(50) m51(51) m52(52) m53(53) m54(54) m55(55) m56(56) m57(57) m58(58) m59(59) m6(6) m7(7) m8(8) m9(9)

The set of minutes within an hour when the scheduled action
should take place.
SchedMonth Bits

april(3) august(7) december(11) february(1) january(0) july(6) june(5) march(2) may(4) november(10) october(9) september(8)

The set of months during which the scheduled action should
take place.  Setting multiple bits will include several
months in the set of possible months for this schedule.

Setting all bits will cause the scheduler to ignore the
month.
SchedWeekDay Bits

friday(5) monday(1) saturday(6) sunday(0) thursday(4) tuesday(2) wednesday(3)

The set of weekdays on which the scheduled action should
take place.  Setting multiple bits will include several
weekdays in the set of possible weekdays for this schedule.
Setting all bits will cause the scheduler to ignore the
weekday.
SecondaryState INTEGER

degrade(6) diagnostic(3) fault(2) firmwarepump(9) initializing(7) manual(1) normal(5) notapplicable(0) overload(4) swdownload(8)

For each PrimaryState, there might be an associated secondary state
ServerType INTEGER

ftp(2) other(7) radius(5) snmp(3) syslog(4) tacacs(6) telnet(1)

This TEXTUAL-CONVENTION describes the INET services available on the SCM.
ShelfId Integer32 (1..99)
Uniquely identifies the shelf. Number of 99 indicate an invalid ShelfId.
SshAuthMethod INTEGER

password(1) public-key(2)

This TEXTUAL-CONVENTION describes the authentication method available in SSH
on the C4.
SshCipher Bits

aes(5) arcfour(2) blowfish(3) cast(4) other(0) threedes(1)

This TEXTUAL-CONVENTION describes the ciphers available in SSH
on the C4.
SshCipherType INTEGER

aes128(6) aes192(7) aes256(8) arcfour(3) blowfish(4) cast128(5) des(9) other(1) rc4(10) threedes(2)

This TEXTUAL-CONVENTION describes the specific cipher type
on the C4.
SshMacAlg INTEGER

hmac-sha1(2) none(1)

This TEXTUAL-CONVENTION describes the MAC algorithm available in SSH
on the C4.
SshProtocol INTEGER

ssh1(1) ssh1ssh2(3) ssh2(2)

This TEXTUAL-CONVENTION describes the SSH protocol versions
available in SSH on the C4.
SshService INTEGER

sftp(2) terminal(1)

This TEXTUAL-CONVENTION describes the SSH service types
available in SSH on the C4.
UnknownState INTEGER

known(0) unknown(1)

Similar to TMN representation of the Unknown Status.
VlanId Integer32 (1..1000000)
The unique identifier for a Virtual LAN. A value of 1000000 indicates unknown VLAN.

Used by