CM-SYSTEM-MIB
ADVA AG Optical NetworkingThis module defines the System MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.
snmptranslate -m CM-SYSTEM-MIB -Tpsnmpwalk -v2c -c <community> -m CM-SYSTEM-MIB <host> 1.3.6.1.4.1.2544.1.12.2Imports
| ADVA-MIB | FileTransferProtocol, TrapCounter, fsp150cm |
|---|---|
| CM-COMMON-MIB | IpVersion, RestartType |
| IF-MIB | InterfaceIndex |
| IPV6-TC | Ipv6Address |
| LLDP-V2-MIB | lldpV2RemEntry |
| LLDP-V2-TC-MIB | LldpV2DestAddressTableIndex |
| SNMP-FRAMEWORK-MIB | SnmpEngineID |
| SNMP-TARGET-MIB | snmpTargetAddrName |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, PhysAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IcmSystemMIB | 1.3.6.1.4.1.2544.1.12.2 | ||||||||||||
identity This module defines the System MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA. | |||||||||||||
| NcmSystemObjects | 1.3.6.1.4.1.2544.1.12.2.1 | ||||||||||||
| NcmErrorInfoObjects | 1.3.6.1.4.1.2544.1.12.2.1.1 | ||||||||||||
| SlastSetErrorInformation | 1.3.6.1.4.1.2544.1.12.2.1.1.1 | DisplayString (SIZE (0..256)) | RO | ||||||||||
scalar · DisplayString (SIZE (0..256)) · read-only · current This provides detailed information on the last SNMP SET operation failure on the enterprise MIBs. | |||||||||||||
| NcmCliObjects | 1.3.6.1.4.1.2544.1.12.2.1.2 | ||||||||||||
| ScliCmdPromptPrefix | 1.3.6.1.4.1.2544.1.12.2.1.2.1 | DisplayString (SIZE (0..64)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..64)) · read-write · current User specified command prompt prefix, used by the CLI, at the system level. | |||||||||||||
| NcmAccessProtocols | 1.3.6.1.4.1.2544.1.12.2.1.3 | ||||||||||||
| StelnetEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.1 | TruthValue | RW | 2 | |||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the TELNET protocol on the system. Example values from LibreNMS test devices
| |||||||||||||
| SsshEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.2 | TruthValue | RW | 1 | |||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the Secure Shell protocol on the system. Example values from LibreNMS test devices
| |||||||||||||
| SftpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.3 | TruthValue | RW | 2 | |||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the File Transfer Protocol (FTP) on the system. Example values from LibreNMS test devices
| |||||||||||||
| SscpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.4 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the Secure Copy (SCP) on the system. | |||||||||||||
| SserialPortEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.5 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the Serial Port on the system. | |||||||||||||
| ShttpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.6 | TruthValue | RW | 2 | |||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the HTTP protocol on the system. Example values from LibreNMS test devices
| |||||||||||||
| ShttpsEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.7 | TruthValue | RW | 1 | |||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the HTTP protocol on the system. Example values from LibreNMS test devices
| |||||||||||||
| SsftpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.8 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the SFTP protocol on the system. | |||||||||||||
| StftpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.9 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the TFTP protocol on the system. | |||||||||||||
| SnetconfOverSSHEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.10 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the NETCONF over SSH on the system. | |||||||||||||
| SusbPortEnabled | 1.3.6.1.4.1.2544.1.12.2.1.3.11 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the USB Host Port on the system. | |||||||||||||
| NcmSysSecObjects | 1.3.6.1.4.1.2544.1.12.2.1.4 | ||||||||||||
| SsecurityBanner | 1.3.6.1.4.1.2544.1.12.2.1.4.1 | DisplayString (SIZE (0..2000)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..2000)) · read-write · current This provides ability to manage the security banner text used for Graphical User Interface as well as CLI access. | |||||||||||||
| TaclTable | 1.3.6.1.4.1.2544.1.12.2.1.4.2 | NA | |||||||||||
table · not-accessible · current A list of entries corresponding to the access control IP network addresses. Agent provides upto 10 access control IP network addresses to be configured. Access is only 'permitted' from these IP network addresses. | |||||||||||||
| RaclEntry | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1 | NA | |||||||||||
row · not-accessible · current An entry containing information applicable to a particular Access Control IP Network Address that can be configured.
| |||||||||||||
| CaclEntryIndex | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.1 | Integer32 (1..32) | RO | ||||||||||
column · Integer32 (1..32) · read-only · current An arbitrary integer index value used to uniquely identify an ACL entry within an ACL. The manager may not assume any particular semantics or meaning to this index, except that it identifies a logical row in the table. | |||||||||||||
| CaclEntryFilterAction | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.2 | CmAclFilterAction | RO | ||||||||||
column · CmAclFilterAction · read-only · current Whether the network IP address specified by aclEntryNetworkAddress and aclEntryNetworkMask has permission to access the system. Currently, only 'permit' is supported. | |||||||||||||
| CaclEntryNetworkAddress | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.3 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current The network IP address of the entry that will be permitted to access the system. | |||||||||||||
| CaclEntryNetworkMask | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.4 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current The network IP mask of the entry that will be permitted to access the system. | |||||||||||||
| CaclEntryEnabled | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.5 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This enables/disables the entity specified by aclEntryNetworkAddress and aclEntryNetworkMask to access the system. | |||||||||||||
| CaclEntryIpVersion | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.6 | IpVersion | RW | ||||||||||
column · IpVersion · read-write · current This object describe the ip version. | |||||||||||||
| CaclEntryNetworkIpv6Addr | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.7 | Ipv6Address | RW | ||||||||||
column · Ipv6Address · read-write · current This object describe the ipv6 adress. | |||||||||||||
| CaclEntryPrefixLength | 1.3.6.1.4.1.2544.1.12.2.1.4.2.1.8 | Integer32 (0..128) | RW | ||||||||||
column · Integer32 (0..128) · read-write · current This object describe the ipv6 Prefix length. | |||||||||||||
| SserialPortDisconnectAutoLogOff | 1.3.6.1.4.1.2544.1.12.2.1.4.3 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to manage the property of the system, which causes Auto Logoff of the user session on the serial port, when the serial port is disconnected. | |||||||||||||
| SsecurityPromptEnabled | 1.3.6.1.4.1.2544.1.12.2.1.4.4 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This object allows management of the CLI security prompt. | |||||||||||||
| NcmSysModeObjects | 1.3.6.1.4.1.2544.1.12.2.1.5 | ||||||||||||
| SntpMode | 1.3.6.1.4.1.2544.1.12.2.1.5.1 | CmNtpMode | RW | ||||||||||
scalar · CmNtpMode · read-write · current This provides ability to manage the Network Time Protocol (NTP) mode on the system. Currently, the system only supports 'client' mode. | |||||||||||||
| SautoProvMode | 1.3.6.1.4.1.2544.1.12.2.1.5.2 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This provides ability to manage the Auto Provisioning Mode on the system. If the auto provisioning mode is 'off', auto discovery is disabled. Network Elements (shelves) need to be manually configured from the user interfaces. If the auto provisioning mode is 'confirm', Network Elements (shelves) are auto discovered, however, they need to be accepted explicitly from user interfaces to be managed. If the auto provisioning mode is 'auto', Network Elements (shelves) are auto discovered and auto provisioned, as permanent, in the system.
| |||||||||||||
| SsysTimeOfDayType | 1.3.6.1.4.1.2544.1.12.2.1.5.3 | TimeOfDayType | RW | ||||||||||
scalar · TimeOfDayType · read-write · current This object provides ability to configure System Time of Day source. This can be local, ntp or ptp. Before setting sysTimeOfDayType the f3PtpSysTimeOfDayClock object must be set to configure PTP Telecom Slave object to be used as Clock source. | |||||||||||||
| SntpServerConfigType | 1.3.6.1.4.1.2544.1.12.2.1.5.4 | ServerConfigType | RW | ||||||||||
scalar · ServerConfigType · read-write · current This object describe the ntp server configure type. | |||||||||||||
| SsysLogServerConfigType | 1.3.6.1.4.1.2544.1.12.2.1.5.5 | ServerConfigType | RW | ||||||||||
scalar · ServerConfigType · read-write · current This object describe the sys log server configure type. | |||||||||||||
| SsysUseUtcLeapOffsetEnable | 1.3.6.1.4.1.2544.1.12.2.1.5.6 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This attribute indicates whether to use the currentUtcLeapOffset in Announce message from PTP to get UTC time from TAI based timestamps in case we want DM/TWAMP timestamping based on UTC time. This attribute only works when PTP/TimeClock is configured as source of system time of day. | |||||||||||||
| SsysLogTimestampFormat | 1.3.6.1.4.1.2544.1.12.2.1.5.7 | SysLogFormatType | RW | ||||||||||
scalar · SysLogFormatType · read-write · current This object describes the syslog server timestamp format type. | |||||||||||||
| SsysLogFacilityCode | 1.3.6.1.4.1.2544.1.12.2.1.5.8 | Integer32 (0..23) | RW | ||||||||||
scalar · Integer32 (0..23) · read-write · current This object describes the syslog server facility code. | |||||||||||||
| NcmDatabaseObjects | 1.3.6.1.4.1.2544.1.12.2.1.6 | ||||||||||||
| SdatabaseAction | 1.3.6.1.4.1.2544.1.12.2.1.6.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Initiates a configuration database action. This object is
write only. Supported actions are:
backup(1) - Backup the saved configuration database.
restore(2) - Restore the database to the standby partition.
activate(3) - Switches the standby and active partitions and
restarts the system.
save-sysdefaults(4) - Save the database as system defaults.
new-sysdefaults(5) - Restart the system and overwrite the
old system default database with the
factory default database.
restore-sysdefaults(6) - Restart the system using the system
default database.
restore-factorydefaults(7) - Restart the system using the factory
default database.
propagate-to-standby-nemi(8) - Propagate the running database
to standby NEMI and activate it.
force-normal(9) - Accept the database of the NEMI when the NEMI is in DB_maint status.
| |||||||||||||
| SdatabaseLastSaveTime | 1.3.6.1.4.1.2544.1.12.2.1.6.2 | DateAndTime | RO | ||||||||||
scalar · DateAndTime · read-only · current This object gives value of the last database save time. | |||||||||||||
| TdatabaseTable | 1.3.6.1.4.1.2544.1.12.2.1.6.3 | NA | |||||||||||
table · not-accessible · current This table lists information about thns. | |||||||||||||
| RdatabaseEntry | 1.3.6.1.4.1.2544.1.12.2.1.6.3.1 | NA | |||||||||||
| CdatabaseIndex | 1.3.6.1.4.1.2544.1.12.2.1.6.3.1.1 | Integer32 (1..2) | RO | ||||||||||
column · Integer32 (1..2) · read-only · current An arbitrary integer index value used to uniquely identify an entry within the databaseTable. | |||||||||||||
| CdatabaseType | 1.3.6.1.4.1.2544.1.12.2.1.6.3.1.2 | CmVersionType | RO | ||||||||||
column · CmVersionType · read-only · current The type of database partition. | |||||||||||||
| CdatabaseVersion | 1.3.6.1.4.1.2544.1.12.2.1.6.3.1.3 | DisplayString (SIZE (0..16)) | RO | ||||||||||
column · DisplayString (SIZE (0..16)) · read-only · current The database version string. | |||||||||||||
| SdatabaseActionPassphrase | 1.3.6.1.4.1.2544.1.12.2.1.6.4 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current Pass-phrase used to generate key for encrypting private keys. | |||||||||||||
| NcmSoftwareObjects | 1.3.6.1.4.1.2544.1.12.2.1.7 | ||||||||||||
| SsoftwareAction | 1.3.6.1.4.1.2544.1.12.2.1.7.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object is write only. Setting this object initiates
the specified action.
Supported actions are:
install(1) - Install software.
schedule-upgrade(2) - Schedule a software upgrade. At the
scheduled time, the system will reboot and
load the software image stored on the
standby partition. The scheduled time
can be specified by softwareUpgradeTime.
Also see softwareValidationTimer.
cancel-upgrade(3) - Cancel a scheduled software upgrade.
validate-upgrade(4) - Indicate software as valid and cancel the
validation timer.
revert-upgrade(5) - Revert to previous software image if it
still exists.
propagate-to-standby-nemi(6) - Propagate the running software release
to standby NEMI and active it.
| |||||||||||||
| SsoftwareUpgradeTime | 1.3.6.1.4.1.2544.1.12.2.1.7.2 | DateAndTime | RW | ||||||||||
scalar · DateAndTime · read-write · current Specifies the date and time to perform a software upgrade reboot. If this object is set to a date and time in the past or has never been set, the upgrade reboot will happen as soon as softwareAction is set to schedule-upgrade(2). This value becomes read-only when an upgrade has been scheduled. Default value is 1-1-2000 00:00:00. | |||||||||||||
| SsoftwareValidationTimer | 1.3.6.1.4.1.2544.1.12.2.1.7.3 | INTEGER (0 | 10..720) | RW | ||||||||||
scalar · INTEGER (0 | 10..720) · read-write · current Time in minutes before the system will reboot and revert to the active software after a software upgrade. If set to 0, the timer is disabled and the software will automatically be validated after a software upgrade reboot. This object becomes read-only when the software validation timer is active. Default value is 0. When enabled, valid values of the timer range from 10 minutes to 720 minutes. | |||||||||||||
| TsoftwareTable | 1.3.6.1.4.1.2544.1.12.2.1.7.4 | NA | |||||||||||
table · not-accessible · current This table lists information about the software installed in the active and standby partitions. | |||||||||||||
| RsoftwareEntry | 1.3.6.1.4.1.2544.1.12.2.1.7.4.1 | NA | |||||||||||
| CsoftwareIndex | 1.3.6.1.4.1.2544.1.12.2.1.7.4.1.1 | Integer32 (1..3) | RO | ||||||||||
column · Integer32 (1..3) · read-only · current An arbitrary integer index value used to uniquely identify an entry within the softwareTable. | |||||||||||||
| CsoftwareType | 1.3.6.1.4.1.2544.1.12.2.1.7.4.1.2 | CmVersionType | RO | ||||||||||
column · CmVersionType · read-only · current The type of software partition. | |||||||||||||
| CsoftwareVersion | 1.3.6.1.4.1.2544.1.12.2.1.7.4.1.3 | DisplayString (SIZE (0..16)) | RO | ||||||||||
column · DisplayString (SIZE (0..16)) · read-only · current The software version string. | |||||||||||||
| SsoftwareAffectedEntity | 1.3.6.1.4.1.2544.1.12.2.1.7.5 | AffectedEntity | RW | ||||||||||
scalar · AffectedEntity · read-write · current Affected Entity. | |||||||||||||
| SsoftwarePeerCondition | 1.3.6.1.4.1.2544.1.12.2.1.7.6 | PeerUpgradeReadyCondition | RW | ||||||||||
scalar · PeerUpgradeReadyCondition · read-write · current Peer Upgrade Ready Condition Entity. | |||||||||||||
| SpeerUpgradeStatus | 1.3.6.1.4.1.2544.1.12.2.1.7.7 | PeerUpgradeStatus | RO | ||||||||||
scalar · PeerUpgradeStatus · read-only · current Peer Upgrade Status Entity. | |||||||||||||
| NcmFileServicesObjects | 1.3.6.1.4.1.2544.1.12.2.1.8 | ||||||||||||
| SfileServicesAction | 1.3.6.1.4.1.2544.1.12.2.1.8.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object is write only. Setting this object initiates
a file transfer
Supported actions are:
get-database(1) - Copy a backup database from a
remote server and place it in the staging
area. (See databaseAction)
put-database(2) - Copy a backup database to a remote
server. (See databaseAction)
software-copy(3) - Transfer a software image file to the
system and write it to the standby
partition.
get-sys-database(4) - Copy a system database from a
remote server and place it in the staging
area. (See databaseAction)
put-sys-database(5) - Copy a system database to a remote
server. (See databaseAction)
get-defaultsvalue-file(6) - Transfer the Defaults Value file
to the system.
put-sysresetdebuginfo-file(7) - Transfer the System Reset Debug Information
file to a remote server.
put-securitylog-file(8) - Transfer the System Security Log Information
file to a remote server.
put-alarmlog-file(9) - Transfer the System Alarm Log Information
file to a remote server.
put-audit-file(10) - Transfer the System Audit Log Information
file to a remote server.
get-config-file(11) - Transfer the Configuration File from a remote server.
put-config-file(12) - Transfer the Configuration File to a remote server.
put-sat-result(13) - Transfer the SAT test result file to a remote server.
get-ssl-certificate(14) - Transfer the SSL Certificate file to the system.
get-ssl-private-key(15) - Transfer the SSL Private Key file to the system.
get-ssl-encrypt-private-Key(16) - Transfer the SSL Encrypted Private Key file to the system.
get-ssl-key-pair(17) - Transfer the SSL Key Pair file to the system.
put-csr(18) - Transfer the CSR file to the system.
put-rfc2544-test-report(19) - Transfer the Rfc2544 test report to the system.
| |||||||||||||
| SfileServicesMethod | 1.3.6.1.4.1.2544.1.12.2.1.8.2 | CmFileTransferMethod | RW | ||||||||||
scalar · CmFileTransferMethod · read-write · current Specifies the method of transferring the file. Note that web(4) is a read-only enumeration. | |||||||||||||
| SfileServicesServerIp | 1.3.6.1.4.1.2544.1.12.2.1.8.3 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of the remote server. The value of this object is cleared when fileServicesAction is set. | |||||||||||||
| SfileServicesUserId | 1.3.6.1.4.1.2544.1.12.2.1.8.4 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current User ID to use to authenticate the file transfer. The value of this object is cleared when fileServicesAction is set. | |||||||||||||
| SfileServicesPassword | 1.3.6.1.4.1.2544.1.12.2.1.8.5 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current User password to authenticate the file transfer. Reading this object will return an empty string if the password has not been set or ***** if the password has been set. The value of this object is cleared when fileServicesAction is set. | |||||||||||||
| SfileServicesRemoteFile | 1.3.6.1.4.1.2544.1.12.2.1.8.6 | DisplayString (SIZE (0..256)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..256)) · read-write · current Path and name of the remote file. The value of this object is cleared when fileServicesAction is set. | |||||||||||||
| SfileServicesStatus | 1.3.6.1.4.1.2544.1.12.2.1.8.7 | CmFileServicesStatus | RO | ||||||||||
scalar · CmFileServicesStatus · read-only · current Status of the user initiated file transfer. | |||||||||||||
| SfileServicesPercentComplete | 1.3.6.1.4.1.2544.1.12.2.1.8.8 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current Percent completion of operation. | |||||||||||||
| SfileServicesMode | 1.3.6.1.4.1.2544.1.12.2.1.8.9 | CmFileServicesMode | RO | ||||||||||
scalar · CmFileServicesMode · read-only · current This object provides information on the current state of file services. | |||||||||||||
| SfileServicesServerType | 1.3.6.1.4.1.2544.1.12.2.1.8.10 | FileTransferServerType | RW | ||||||||||
scalar · FileTransferServerType · read-write · current This object describe the remote server's address type. | |||||||||||||
| SfileServicesServerIpv6Addr | 1.3.6.1.4.1.2544.1.12.2.1.8.11 | Ipv6Address | RW | ||||||||||
scalar · Ipv6Address · read-write · current IPv6 address of the remote server. The value of this object is cleared when fileServicesAction is set. | |||||||||||||
| SfileServicesDbFileName | 1.3.6.1.4.1.2544.1.12.2.1.8.12 | DisplayString (SIZE (0..256)) | RO | ||||||||||
scalar · DisplayString (SIZE (0..256)) · read-only · current Name of the upload unique database file. | |||||||||||||
| SfileServicesAffectedEntity | 1.3.6.1.4.1.2544.1.12.2.1.8.13 | AffectedEntity | RW | ||||||||||
scalar · AffectedEntity · read-write · current Affected Entity. | |||||||||||||
| SfileServicesSslKeyPairName | 1.3.6.1.4.1.2544.1.12.2.1.8.14 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current This is a unique name for the SSL key pair. | |||||||||||||
| SfileServicesDecryptionPassword | 1.3.6.1.4.1.2544.1.12.2.1.8.15 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current This is the decryption password for the SSL file. | |||||||||||||
| SfileServicesCsrName | 1.3.6.1.4.1.2544.1.12.2.1.8.16 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current This is a unique name for the CSR. | |||||||||||||
| NcmLogObjects | 1.3.6.1.4.1.2544.1.12.2.1.9 | ||||||||||||
| NcmSysLogObjects | 1.3.6.1.4.1.2544.1.12.2.1.9.1 | ||||||||||||
| TsysLogServerTable | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1 | NA | |||||||||||
table · not-accessible · current This table allows configuration of the remote syslog hosts. | |||||||||||||
| RsysLogServerEntry | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1 | NA | |||||||||||
| CsysLogServerIndex | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.1 | Integer32 (1..3) | RO | ||||||||||
column · Integer32 (1..3) · read-only · current An integer index value used to uniquely identify an entry within the sysLogServerTable. | |||||||||||||
| CsysLogIpAddress | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.2 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current IP address of the remote syslog server. Value of 0.0.0.0 indicates the sys log server is not configured. | |||||||||||||
| CsysLogPort | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.3 | Integer32 (1..65535) | RW | ||||||||||
column · Integer32 (1..65535) · read-write · current Optional port address of the remote log server. If not specified, the default port for the standard syslog utility (UDP Port 514) will be used. | |||||||||||||
| CsysLogIpVersion | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.4 | IpVersion | RW | ||||||||||
column · IpVersion · read-write · current This object describe the ip version. | |||||||||||||
| CsysLogIpv6Addr | 1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.5 | Ipv6Address | RW | ||||||||||
column · Ipv6Address · read-write · current This object describe the ipv6 address. | |||||||||||||
| NcmSecLogObjects | 1.3.6.1.4.1.2544.1.12.2.1.9.2 | ||||||||||||
| SsecLog2sysLogEnabled | 1.3.6.1.4.1.2544.1.12.2.1.9.2.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the system security log to syslog. | |||||||||||||
| NcmAuditLogObjects | 1.3.6.1.4.1.2544.1.12.2.1.9.3 | ||||||||||||
| SauditLog2sysLogEnabled | 1.3.6.1.4.1.2544.1.12.2.1.9.3.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the system audit log to syslog. | |||||||||||||
| SauditLog2fileEnabled | 1.3.6.1.4.1.2544.1.12.2.1.9.3.2 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the system audit log to file. | |||||||||||||
| NcmAlarmLogObjects | 1.3.6.1.4.1.2544.1.12.2.1.9.4 | ||||||||||||
| SalarmLog2sysLogEnabled | 1.3.6.1.4.1.2544.1.12.2.1.9.4.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the system alarm log to syslog. | |||||||||||||
| SalarmLog2fileEnabled | 1.3.6.1.4.1.2544.1.12.2.1.9.4.2 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the system alarm log to file. | |||||||||||||
| NcmTimeObjects | 1.3.6.1.4.1.2544.1.12.2.1.10 | ||||||||||||
| SntpClientEnabled | 1.3.6.1.4.1.2544.1.12.2.1.10.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This allows to enable/disable the NTP client. | |||||||||||||
| SntpPrimaryServer | 1.3.6.1.4.1.2544.1.12.2.1.10.2 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of the primary remote NTP time server. Value of 0.0.0.0 indicates the NTP server is not configured. | |||||||||||||
| SntpBackupServer | 1.3.6.1.4.1.2544.1.12.2.1.10.3 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of the backup remote NTP time server. Value of 0.0.0.0 indicates the NTP server is not configured. | |||||||||||||
| SntpType | 1.3.6.1.4.1.2544.1.12.2.1.10.4 | CmNtpType | RO | ||||||||||
scalar · CmNtpType · read-only · current Type of communication with the remote NTP server. | |||||||||||||
| SntpActiveServer | 1.3.6.1.4.1.2544.1.12.2.1.10.5 | CmNtpServerType | RO | ||||||||||
scalar · CmNtpServerType · read-only · current Indication of which server is currently active. | |||||||||||||
| SntpSwitchServer | 1.3.6.1.4.1.2544.1.12.2.1.10.6 | CmNtpServerType | RW | ||||||||||
scalar · CmNtpServerType · read-write · current Operation to switch the NTP Server. | |||||||||||||
| SntpServerRoundTripDelay | 1.3.6.1.4.1.2544.1.12.2.1.10.7 | Integer32 | RO | ||||||||||
scalar · Integer32 · read-only · current This object provides the round-trip delay (in microseconds) to the NTP Server. It returns a value of 0 if NTP is not enabled. | |||||||||||||
| SntpServerPrecision | 1.3.6.1.4.1.2544.1.12.2.1.10.8 | Integer32 | RO | ||||||||||
scalar · Integer32 · read-only · current This object provides the precision (in microseconds) to the NTP Server. | |||||||||||||
| SntpPollingInterval | 1.3.6.1.4.1.2544.1.12.2.1.10.9 | Integer32 | RW | ||||||||||
scalar · Integer32 · read-write · current This object allows ability to configure the NTP polling interval in seconds. Polling interval is the time between successive NTP client requests to update local time based on time at the NTP server. | |||||||||||||
| SntpPrimaryServerIpVersion | 1.3.6.1.4.1.2544.1.12.2.1.10.10 | IpVersion | RW | ||||||||||
scalar · IpVersion · read-write · current This object describe the ipversion of ntp server. | |||||||||||||
| SntpPrimaryServerIpv6Addr | 1.3.6.1.4.1.2544.1.12.2.1.10.11 | Ipv6Address | RW | ||||||||||
scalar · Ipv6Address · read-write · current This object describe the ipv6 adress of ntp primary server. | |||||||||||||
| SntpBackupServerIpVersion | 1.3.6.1.4.1.2544.1.12.2.1.10.12 | IpVersion | RW | ||||||||||
scalar · IpVersion · read-write · current This object describe the ipversion of ntp server. | |||||||||||||
| SntpBackupServerIpv6Addr | 1.3.6.1.4.1.2544.1.12.2.1.10.13 | Ipv6Address | RW | ||||||||||
scalar · Ipv6Address · read-write · current This object describe the ipv6 adress of ntp backup server. | |||||||||||||
| SntpPrimaryServerAuthKey | 1.3.6.1.4.1.2544.1.12.2.1.10.14 | VariablePointer | RW | ||||||||||
scalar · VariablePointer · read-write · current This object specifies the authentication key for the primary NTP server. | |||||||||||||
| SntpBackupServerAuthKey | 1.3.6.1.4.1.2544.1.12.2.1.10.15 | VariablePointer | RW | ||||||||||
scalar · VariablePointer · read-write · current This object specifies the authentication key for the backup NTP server. | |||||||||||||
| Tf3NtpAuthKeyTable | 1.3.6.1.4.1.2544.1.12.2.1.10.16 | NA | |||||||||||
table · not-accessible · current This table specifies the Keys used for NTP Authentication. | |||||||||||||
| Rf3NtpAuthKeyEntry | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1 | NA | |||||||||||
| Cf3NtpAuthKeyId | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.1 | Unsigned32 | NA | ||||||||||
column · Unsigned32 · not-accessible · current This is the unique index for the NTP Authentication Key. | |||||||||||||
| Cf3NtpAuthKeyNumber | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.2 | Unsigned32 | RW | ||||||||||
column · Unsigned32 · read-write · current This is the identifier used by the NTP authentication protocol using which the Client and Server identify the key. | |||||||||||||
| Cf3NtpAuthKeyType | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.3 | NtpAuthKeyType | RW | ||||||||||
column · NtpAuthKeyType · read-write · current Authentication type, MD5 or SHA-1. | |||||||||||||
| Cf3NtpAuthKey | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.4 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current This is the key value and length depends on the authentication type used. It is 16 character printable string for MD5 excluding whitespace and '#' and for SHA-1 it is a 40 character hex-encoded string. | |||||||||||||
| Cf3NtpAuthKeyStorageType | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.5 | StorageType | RC | ||||||||||
column · StorageType · read-create · current The storage type for this conceptual row. | |||||||||||||
| Cf3NtpAuthKeyRowStatus | 1.3.6.1.4.1.2544.1.12.2.1.10.16.1.6 | RowStatus | RC | ||||||||||
column · RowStatus · read-create · current The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3NtpAuthKeyRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3NtpAuthKeyRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3NtpAuthKeyRowStatus object may be modified if the associated instance of this object is equal to active(1). | |||||||||||||
| NcmSnmpObjects | 1.3.6.1.4.1.2544.1.12.2.1.11 | ||||||||||||
| Tf3SnmpTargetAddrExtTable | 1.3.6.1.4.1.2544.1.12.2.1.11.1 | NA | |||||||||||
table · not-accessible · current This table is an extension of the standard snmpTargetAddrTable(SNMP-TARGET-MIB). This table is used to manage the SNMP Dying Gasp support. | |||||||||||||
| Rf3SnmpTargetAddrExtEntry | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1 | NA | |||||||||||
row · not-accessible · current A conceptual row in the f3SnmpTargetAddrExtTable.
| |||||||||||||
| Cf3SnmpTargetAddrExtDyingGaspPort | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1.1 | VariablePointer | RO | ||||||||||
column · VariablePointer · read-only · current When SNMP Dying Gasp is enabled at Card level, this attribute provides information on the interface (physical port) through which this Target Address is reachable (using Layer 3 ping, trace route). | |||||||||||||
| Cf3SnmpTargetAddrExtDyingGaspEnabled | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1.2 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current When SNMP Dying Gasp is enabled at Card level, this attribute specifies whether this Target Address entry should be used in the SNMP Dying Gasp TRAP PDU or not. | |||||||||||||
| Cf3SnmpTargetAddrExtDyingGaspActive | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1.3 | TruthValue | RO | ||||||||||
column · TruthValue · read-only · current When SNMP Dying Gasp is enabled at Card level, in case of multiple target addresses resolving to the same interface (port), this flag indicates which target address is used for the SNMP TRAP PDU. | |||||||||||||
| Cf3SnmpTargetAddrExtBulkTrapsEnabled | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1.4 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current Provides ability to enable/disable the Snmp Bulk Traps on the Target Address. | |||||||||||||
| Cf3SnmpTargetAddrExtLifetime | 1.3.6.1.4.1.2544.1.12.2.1.11.1.1.5 | F3TargetAddressLifetime | RW | ||||||||||
column · F3TargetAddressLifetime · read-write · current Provides a time after which target address entry will automatically be deleted. SNMP packet received from snmpTargetAddrTAddress resets timer to its original value. | |||||||||||||
| Sf3SnmpEngineID | 1.3.6.1.4.1.2544.1.12.2.1.11.2 | SnmpEngineID | RW | ||||||||||
scalar · SnmpEngineID · read-write · current An SNMP engine's administratively-unique identifier. Please note that f3SnmpEngineID differs from the standard snmpEngineID (SNMP-FRAMEWORK-MIB) with MAX-ACCESS as read-write. | |||||||||||||
| Sf3SnmpLongIfAlias | 1.3.6.1.4.1.2544.1.12.2.1.11.3 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable longer version of ifAlias. If enabled, ifAlias variable can support up to 255 character string and when disabled ifAlias is limited to 64 character string. When disabled and if alias is longer than 64 characters the ifAlias will return a string that is truncated to 64 characters. | |||||||||||||
| NcmResetCauseObjects | 1.3.6.1.4.1.2544.1.12.2.1.12 | ||||||||||||
| Sf3SysLastResetType | 1.3.6.1.4.1.2544.1.12.2.1.12.1 | RestartType | RO | ||||||||||
scalar · RestartType · read-only · current This provides the System Last Reset Type. | |||||||||||||
| Sf3SysLastResetCauseType | 1.3.6.1.4.1.2544.1.12.2.1.12.2 | CmRestartCauseType | RO | ||||||||||
scalar · CmRestartCauseType · read-only · current This provides the System Last Reset Cause Type. | |||||||||||||
| Sf3SysLastAbnormalResetTimestamp1 | 1.3.6.1.4.1.2544.1.12.2.1.12.3 | DateAndTime | RO | ||||||||||
scalar · DateAndTime · read-only · current This provides the timestamp of the most recent abnormal reset. Note that the system keeps debug logs with 3 most recent abnormal resets. 8 octets of 0 value indicates that there was no abnormal reset of the system. | |||||||||||||
| Sf3SysLastAbnormalResetTimestamp2 | 1.3.6.1.4.1.2544.1.12.2.1.12.4 | DateAndTime | RO | ||||||||||
scalar · DateAndTime · read-only · current This provides the timestamp of the second most recent abnormal reset. Note that the system keeps debug logs with 3 most recent abnormal resets. 8 octets of 0 value indicates that there was only one (f3SysLastAbnormalResetTimestamp1) abnormal reset of the system. | |||||||||||||
| Sf3SysLastAbnormalResetTimestamp3 | 1.3.6.1.4.1.2544.1.12.2.1.12.5 | DateAndTime | RO | ||||||||||
scalar · DateAndTime · read-only · current This provides the timestamp of the third most recent abnormal reset. Note that the system keeps debug logs with 3 most recent abnormal resets. 8 octets of 0 value indicates that there were only two (f3SysLastAbnormalResetTimestamp1, f3SysLastAbnormalResetTimestamp2) abnormal resets of the system. | |||||||||||||
| Sf3SysResetButtonControl | 1.3.6.1.4.1.2544.1.12.2.1.12.6 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable the use of the push button reset swith. | |||||||||||||
| Nf3NotifObjects | 1.3.6.1.4.1.2544.1.12.2.1.13 | ||||||||||||
| Sf3DatabaseSyncTrapObject | 1.3.6.1.4.1.2544.1.12.2.1.13.1 | VariablePointer | NA | ||||||||||
scalar · VariablePointer · not-accessible · current This object provides the Object Identifier (OID) of the entity that needs to be synchronized. This object is not accessible, it is only carried in the f3DatabaseSyncTrap notification. | |||||||||||||
| Nf3ConfigFileObjects | 1.3.6.1.4.1.2544.1.12.2.1.14 | ||||||||||||
| Sf3ConfigFileActionFileName | 1.3.6.1.4.1.2544.1.12.2.1.14.1 | DisplayString (SIZE (0..256)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..256)) · read-write · current Configuration File name on which configFileAction is initiated. | |||||||||||||
| Sf3ConfigFileAction | 1.3.6.1.4.1.2544.1.12.2.1.14.2 | F3ConfigFileAction | RW | ||||||||||
scalar · F3ConfigFileAction · read-write · current Configuration File action to invoke config file operations. | |||||||||||||
| Sf3ConfigFileStatus | 1.3.6.1.4.1.2544.1.12.2.1.14.3 | F3ConfigFileStatus | RO | ||||||||||
scalar · F3ConfigFileStatus · read-only · current This object provides status of Configuration File actions. | |||||||||||||
| Sf3ConfigFileErrorInformation | 1.3.6.1.4.1.2544.1.12.2.1.14.4 | DisplayString (SIZE (0..512)) | RO | ||||||||||
scalar · DisplayString (SIZE (0..512)) · read-only · current This object provides additional information for failed Configuration File actions. | |||||||||||||
| Tf3ConfigFileTable | 1.3.6.1.4.1.2544.1.12.2.1.14.5 | NA | |||||||||||
table · not-accessible · current This table lists information about the configuration files that are resident on the node. | |||||||||||||
| Rf3ConfigFileEntry | 1.3.6.1.4.1.2544.1.12.2.1.14.5.1 | NA | |||||||||||
| Cf3ConfigFileIndex | 1.3.6.1.4.1.2544.1.12.2.1.14.5.1.1 | Integer32 | NA | ||||||||||
column · Integer32 · not-accessible · current An arbitrary integer index value used to uniquely identify an entry within the f3ConfigFileTable. | |||||||||||||
| Cf3ConfigFileName | 1.3.6.1.4.1.2544.1.12.2.1.14.5.1.2 | DisplayString (SIZE (0..255)) | RO | ||||||||||
column · DisplayString (SIZE (0..255)) · read-only · current Name of the configuration file. | |||||||||||||
| Cf3ConfigFileDescription | 1.3.6.1.4.1.2544.1.12.2.1.14.5.1.3 | DisplayString (SIZE (0..256)) | RW | ||||||||||
column · DisplayString (SIZE (0..256)) · read-write · current User description of the configuration file. | |||||||||||||
| Sf3ConfigFilePercentComplete | 1.3.6.1.4.1.2544.1.12.2.1.14.6 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current This object provides configure file percent complete. | |||||||||||||
| Sf3ConfigFilePassphrase | 1.3.6.1.4.1.2544.1.12.2.1.14.7 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current Pass-phrase used to generate key for encrypting private keys. | |||||||||||||
| NcmFeatureManagementObjects | 1.3.6.1.4.1.2544.1.12.2.1.15 | ||||||||||||
| Tf3SystemFeatureTable | 1.3.6.1.4.1.2544.1.12.2.1.15.1 | NA | |||||||||||
table · not-accessible · current This table allows ability to manage enabling/disabling system features. | |||||||||||||
| Rf3SystemFeatureEntry | 1.3.6.1.4.1.2544.1.12.2.1.15.1.1 | NA | |||||||||||
row · not-accessible · current A conceptual row in the f3SystemFeatureTable.
| |||||||||||||
| Cf3SystemFeatureIndex | 1.3.6.1.4.1.2544.1.12.2.1.15.1.1.1 | Integer32 | RO | ||||||||||
column · Integer32 · read-only · current An arbitrary integer index value used to uniquely identify an entry within the f3SystemFeatureTable. | |||||||||||||
| Cf3SystemFeatureName | 1.3.6.1.4.1.2544.1.12.2.1.15.1.1.2 | DisplayString (SIZE (0..128)) | RO | ||||||||||
column · DisplayString (SIZE (0..128)) · read-only · current This object provides the name of the system feature. | |||||||||||||
| Cf3SystemFeatureEnabled | 1.3.6.1.4.1.2544.1.12.2.1.15.1.1.3 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This object allows system feature control. If a specific feature is disabled, the relevant operations to use that feature are denied. | |||||||||||||
| NcmLldpV2DestAdressADVAExtObjects | 1.3.6.1.4.1.2544.1.12.2.1.16 | ||||||||||||
| Tf3SystemLldpV2DestAddressADVAExtTable | 1.3.6.1.4.1.2544.1.12.2.1.16.1 | NA | |||||||||||
table · not-accessible · current This extension table adds a row status to allow user add/delete/edit the LLDP Destination Address which is defined to Read-Only in the standard MIB. | |||||||||||||
| Rf3SystemLldpV2DestAddressADVAExtEntry | 1.3.6.1.4.1.2544.1.12.2.1.16.1.1 | NA | |||||||||||
row · not-accessible · current A conceptual row in the f3SystemLldpV2DestAddressADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2DestAddressADVAExtIndex | 1.3.6.1.4.1.2544.1.12.2.1.16.1.1.1 | Integer32 | NA | ||||||||||
column · Integer32 · not-accessible · current An arbitrary integer index value used to uniquely identify an entry within the f3SystemLldpV2DestAddressADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2ADVAExtDestMacAddress | 1.3.6.1.4.1.2544.1.12.2.1.16.1.1.2 | MacAddress | RW | ||||||||||
column · MacAddress · read-write · current This attribute description the standard MIB about LLDP Destination Mac Address. | |||||||||||||
| Cf3SystemLldpV2DestAddressADVAExtRowStatus | 1.3.6.1.4.1.2544.1.12.2.1.16.1.1.3 | RowStatus | RW | ||||||||||
column · RowStatus · read-write · current The status of this row. The f3SystemLldpV2DestAddressADVAExtRowStatus object may be modified if the associated instance of this object is equal to active(1), notInService(2), or notReady(3). | |||||||||||||
| Tf3SystemLldpV2PortConfigADVAExtTable | 1.3.6.1.4.1.2544.1.12.2.1.16.2 | NA | |||||||||||
table · not-accessible · current This extension table adds a row status to allow user add/delete/edit the LLDP Destination Address for one port. | |||||||||||||
| Rf3SystemLldpV2PortConfigADVAExtEntry | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1 | NA | |||||||||||
row · not-accessible · current A conceptual row in the f3SystemLldpV2PortConfigADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtIfIndex | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.1 | InterfaceIndex | NA | ||||||||||
column · InterfaceIndex · not-accessible · current The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the f3SystemLldpV2PortConfigADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtDestAddressIndex | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.2 | LldpV2DestAddressTableIndex | NA | ||||||||||
column · LldpV2DestAddressTableIndex · not-accessible · current The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the f3SystemLldpV2PortConfigADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtAdminStatus | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.3 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The administratively desired status of the local LLDP agent. If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set to a value of 'txOnly(1)', then LLDP agent transmits LLDPframes on this port and it does not store any information about the remote systems connected. If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set to a value of 'rxOnly(2)', then the LLDP agent receives, but it does not transmit LLDP frames on this port. If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set to a value of 'txAndRx(3)', then the LLDP agent transmits and receives LLDP frames on this port. If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set to a value of 'disabled(4)', then LLDP agent does not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's f3SystemLldpV2PortConfigADVAExtAdminStatus becomes disabled, then that information is deleted.
| |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtNotificationEnable | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.4 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current The f3SystemLldpV2PortConfigADVAExtNotificationEnable controls, on a per agent basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not. | |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtTLVsTxEnable | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.5 | Bits | RW | ||||||||||
column · Bits · read-write · current The f3SystemLldpV2PortConfigADVAExtTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the f3SystemLldpV2PortConfigADVAExtTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpV2ConfigManAddrTable. The default value for f3SystemLldpV2PortConfigADVAExtTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
| |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtStorageType | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.6 | StorageType | RC | ||||||||||
column · StorageType · read-create · current The storage type for this conceptual row. | |||||||||||||
| Cf3SystemLldpV2PortConfigADVAExtRowStatus | 1.3.6.1.4.1.2544.1.12.2.1.16.2.1.7 | RowStatus | RC | ||||||||||
column · RowStatus · read-create · current The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SystemLldpV2PortConfigADVAExtRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SystemLldpV2PortConfigADVAExtRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SystemLldpV2PortConfigADVAExtRowStatus object may be modified if the associated instance of this object is equal to active(1). | |||||||||||||
| Tf3SystemLldpV2ManAddrConfigTxPortsADVAExtTable | 1.3.6.1.4.1.2544.1.12.2.1.16.3 | NA | |||||||||||
table · not-accessible · current This extension table adds a row status to allow user add/delete/edit the LLDP Destination Address for one port. | |||||||||||||
| Rf3SystemLldpV2ManAddrConfigTxPortsADVAExtEntry | 1.3.6.1.4.1.2544.1.12.2.1.16.3.1 | NA | |||||||||||
row · not-accessible · current A conceptual row in the f3SystemLldpV2ManAddrConfigTxPortsADVAExtTable. | |||||||||||||
| Cf3SystemLldpV2ManAddrConfigTxPortsADVAExtRefInterface | 1.3.6.1.4.1.2544.1.12.2.1.16.3.1.1 | VariablePointer | NA | ||||||||||
column · VariablePointer · not-accessible · current This object describe the Tx Port is on what interface, its value should be management tunnel or one dcn or none. | |||||||||||||
| Cf3SystemLldpV2ManAddrConfigTxPortsADVAExtEnable | 1.3.6.1.4.1.2544.1.12.2.1.16.3.1.2 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This object describe the interface on Tx Ports whether enabled. | |||||||||||||
| Cf3SystemLldpV2ManAddrConfigTxPortsADVAExtStorageType | 1.3.6.1.4.1.2544.1.12.2.1.16.3.1.3 | StorageType | RC | ||||||||||
column · StorageType · read-create · current The storage type for this conceptual row. | |||||||||||||
| Cf3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus | 1.3.6.1.4.1.2544.1.12.2.1.16.3.1.4 | RowStatus | RC | ||||||||||
column · RowStatus · read-create · current The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus object may be modified if the associated instance of this object is equal to active(1). | |||||||||||||
| Nf3LldpV2ConfigurationADVAExtObjects | 1.3.6.1.4.1.2544.1.12.2.1.17 | ||||||||||||
| Sf3LldpMaxNeighborsAction | 1.3.6.1.4.1.2544.1.12.2.1.17.1 | LldpV2ConfigurationADVAExtMaxNeighborsAction | RW | ||||||||||
scalar · LldpV2ConfigurationADVAExtMaxNeighborsAction · read-write · current Discard: information selected to be discarded is the information in the current LLDPDU. Delete entry::information selected to be discarded is currently in the LLDP remote systems MIB. | |||||||||||||
| NsnmpIPv6UDPDomain | 1.3.6.1.4.1.2544.1.12.2.1.18 | ||||||||||||
| Nf3RawDataObjects | 1.3.6.1.4.1.2544.1.12.2.1.19 | ||||||||||||
| Sf3RawDataServerFtProtocol | 1.3.6.1.4.1.2544.1.12.2.1.19.1 | CmFileTransferMethod | RW | ||||||||||
scalar · CmFileTransferMethod · read-write · current Specifies the method of transferring the file. Note that web(4) is a read-only enumeration. | |||||||||||||
| Sf3RawDataServerFtServerName | 1.3.6.1.4.1.2544.1.12.2.1.19.2 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of the raw data server. Value of 0.0.0.0 indicates the raw data server is not configured. | |||||||||||||
| Sf3RawDataServerFtUserId | 1.3.6.1.4.1.2544.1.12.2.1.19.3 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current User ID to use to authenticate the file transfer. | |||||||||||||
| Sf3RawDataServerFtPasswd | 1.3.6.1.4.1.2544.1.12.2.1.19.4 | DisplayString (SIZE (0..32)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · current User password to authenticate the file transfer. Reading this object will return an empty string if the password has not been set or ***** if the password has been set. | |||||||||||||
| Nf3LldpV2RemoteSystemsData | 1.3.6.1.4.1.2544.1.12.2.1.20 | ||||||||||||
| Tf3LldpV2RemExtTable | 1.3.6.1.4.1.2544.1.12.2.1.20.1 | NA | |||||||||||
table · not-accessible · current This table is an extension of the standard lldpV2RemTable (LLDP-V2-MIB). This table adds remote TTL attribute support | |||||||||||||
| Rf3LldpV2RemExtEntry | 1.3.6.1.4.1.2544.1.12.2.1.20.1.1 | NA | |||||||||||
| Cf3LldpV2RemTTL | 1.3.6.1.4.1.2544.1.12.2.1.20.1.1.1 | Unsigned32 (1..65535) | RO | ||||||||||
column · Unsigned32 (1..65535) · read-only · current Integer value which indicates the number of seconds that the recipient LLDP agent is to regard the information associated with particular MSAP identifier to be valid | |||||||||||||
| Nf3SimpleLtpObjects | 1.3.6.1.4.1.2544.1.12.2.1.21 | ||||||||||||
| Sf3SimpleLtpControl | 1.3.6.1.4.1.2544.1.12.2.1.21.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable the simple ltp on the system. | |||||||||||||
| Sf3SimpleLtpTransferProtocol | 1.3.6.1.4.1.2544.1.12.2.1.21.2 | CmFileTransferMethod | RW | ||||||||||
scalar · CmFileTransferMethod · read-write · current Specifies the method of transferring the file. | |||||||||||||
| Sf3SimpleLtpServerIpv4Addr | 1.3.6.1.4.1.2544.1.12.2.1.21.3 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of the remote server. | |||||||||||||
| Sf3SimpleLtpUserName | 1.3.6.1.4.1.2544.1.12.2.1.21.4 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current User ID to use to authenticate the file transfer. | |||||||||||||
| Sf3SimpleLtpPasswd | 1.3.6.1.4.1.2544.1.12.2.1.21.5 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current Password to use to authenticate the file transfer. | |||||||||||||
| Sf3SimpleLtpConfigFileName | 1.3.6.1.4.1.2544.1.12.2.1.21.6 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current The configure file name used to LTP function. | |||||||||||||
| Sf3SimpleLtpSoftwareFileName | 1.3.6.1.4.1.2544.1.12.2.1.21.7 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current The software file name. | |||||||||||||
| Nf3SysAuthenKeyObjects | 1.3.6.1.4.1.2544.1.12.2.1.22 | ||||||||||||
| Tf3SysAuthKeyTable | 1.3.6.1.4.1.2544.1.12.2.1.22.1 | NA | |||||||||||
table · not-accessible · current . | |||||||||||||
| Rf3SysAuthKeyEntry | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1 | NA | |||||||||||
| Cf3SysAuthKeyIndex | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.1 | Unsigned32 | NA | ||||||||||
column · Unsigned32 · not-accessible · current . | |||||||||||||
| Cf3SysAuthKeyId | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.2 | Unsigned32 | RW | ||||||||||
column · Unsigned32 · read-write · current . | |||||||||||||
| Cf3SysAuthKeyType | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.3 | SysAuthKeyType | RW | ||||||||||
column · SysAuthKeyType · read-write · current Authentication type. | |||||||||||||
| Cf3SysAuthKey | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.4 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current Password for this key. | |||||||||||||
| Cf3SysAuthKeyStorageType | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.5 | StorageType | RC | ||||||||||
column · StorageType · read-create · current The storage type for this conceptual row. | |||||||||||||
| Cf3SysAuthKeyRowStatus | 1.3.6.1.4.1.2544.1.12.2.1.22.1.1.6 | RowStatus | RC | ||||||||||
column · RowStatus · read-create · current The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SysAuthKeyRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SysAuthKeyRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SysAuthKeyRowStatus object may be modified if the associated instance of this object is equal to active(1). | |||||||||||||
| Nf3CallhomeServerObjects | 1.3.6.1.4.1.2544.1.12.2.1.23 | ||||||||||||
| Sf3CallhomeClientIpAddress | 1.3.6.1.4.1.2544.1.12.2.1.23.1 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Callhome client IP address. | |||||||||||||
| Sf3CallhomeState | 1.3.6.1.4.1.2544.1.12.2.1.23.2 | CallhomeState | RO | ||||||||||
scalar · CallhomeState · read-only · current Callhome state. | |||||||||||||
| Nf3SystemInfoObjects | 1.3.6.1.4.1.2544.1.12.2.1.24 | ||||||||||||
| Sf3ApplicationsBootCompleted | 1.3.6.1.4.1.2544.1.12.2.1.24.1 | TruthValue | RO | ||||||||||
scalar · TruthValue · read-only · current This is a flag informing that system completed booting of its applications. | |||||||||||||
| Sf3ApplicationsUpTime | 1.3.6.1.4.1.2544.1.12.2.1.24.2 | TimeTicks | RO | ||||||||||
scalar · TimeTicks · read-only · current The time (in hundredths of second) since the applications of the system were last initialized. | |||||||||||||
| Nf3ZtpObjects | 1.3.6.1.4.1.2544.1.12.2.1.25 | ||||||||||||
| Sf3EnsembleZtpEnabled | 1.3.6.1.4.1.2544.1.12.2.1.25.1 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current This provides ability to enable/disable Ensemble ZTP on the system. | |||||||||||||
| NcmSystemNotifications | 1.3.6.1.4.1.2544.1.12.2.2 | ||||||||||||
| !cmStateChangeTrap | 1.3.6.1.4.1.2544.1.12.2.2.1 | ||||||||||||
notification · current This is the State Change Notification per Interface sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1). | |||||||||||||
| !cmAttributeValueChangeTrap | 1.3.6.1.4.1.2544.1.12.2.2.2 | ||||||||||||
notification · current This is the Attribute Value Change Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1). | |||||||||||||
| !cmObjectCreationTrap | 1.3.6.1.4.1.2544.1.12.2.2.3 | ||||||||||||
notification · current This is the Object Creation Notification sent by the agent. The index value of the SNMP Row that is created is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1). | |||||||||||||
| !cmObjectDeletionTrap | 1.3.6.1.4.1.2544.1.12.2.2.4 | ||||||||||||
notification · current This is the Object Deletion Notification sent by the agent. The index value of the SNMP Row that is deleted is sent by the agent in the form of a varbind list, as per SMIv2 (RFC2578, Section 8.1). | |||||||||||||
| !cmSnmpDyingGaspTrap | 1.3.6.1.4.1.2544.1.12.2.2.5 | ||||||||||||
notification · current This is the Dying Gasp SNMP trap sent by the agent. | |||||||||||||
| !f3DatabaseSyncTrap | 1.3.6.1.4.1.2544.1.12.2.2.6 | ||||||||||||
notification · current This is the Database Synchronization trap sent by the agent for bulk operations. The var bind list can contain multiple variables with OIDs as f3DatabaseSyncTrapObject and values as the OIDs of the entities that need synchronization. The var-binds are sent implicitly, as per SMIv2 (RFC2578, Section 8.1). | |||||||||||||
| NcmSystemConformance | 1.3.6.1.4.1.2544.1.12.2.3 | ||||||||||||
| NcmSystemCompliances | 1.3.6.1.4.1.2544.1.12.2.3.1 | ||||||||||||
| McmSystemCompliance | 1.3.6.1.4.1.2544.1.12.2.3.1.1 | ||||||||||||
compliance · current Describes the requirements for conformance to the CM System group. | |||||||||||||
| NcmSystemGroups | 1.3.6.1.4.1.2544.1.12.2.3.2 | ||||||||||||
| GcmSystemObjectGroup | 1.3.6.1.4.1.2544.1.12.2.3.2.1 | ||||||||||||
group · current A collection of objects used to manage the CM System group.
| |||||||||||||
| GcmSystemNotifGroup | 1.3.6.1.4.1.2544.1.12.2.3.2.2 | ||||||||||||
group · current A collection of notifications used in the CM System group. | |||||||||||||
| GcmSystemObjectGroupCmHub | 1.3.6.1.4.1.2544.1.12.2.3.2.3 | ||||||||||||
group · current A collection of objects used to manage the CM System group.
| |||||||||||||
| Nf3SystemBulkGroups | 1.3.6.1.4.1.2544.1.12.2.3.3 | ||||||||||||
| Gf3SystemObjectBulkGroup | 1.3.6.1.4.1.2544.1.12.2.3.3.1 | ||||||||||||
group · current A collection of objects used to manage the F3 System Bulk group. | |||||||||||||
| Gf3SystemNotifBulkGroup | 1.3.6.1.4.1.2544.1.12.2.3.3.2 | ||||||||||||
| Nf3BulkNotifObjects | 1.3.6.1.4.1.2544.1.12.2.4 | ||||||||||||
| Sf3StartNeEventLogIndex | 1.3.6.1.4.1.2544.1.12.2.4.1 | TrapCounter | RO | ||||||||||
scalar · TrapCounter · read-only · current This object provides the associated neEventsLogged counter for the logged first event (trap) in the bulk trap. | |||||||||||||
| Sf3EndNeEventLogIndex | 1.3.6.1.4.1.2544.1.12.2.4.2 | TrapCounter | RO | ||||||||||
scalar · TrapCounter · read-only · current This object provides the associated neEventsLogged counter for the logged last event (trap) in the bulk trap. | |||||||||||||
| Nf3SystemBulkNotifications | 1.3.6.1.4.1.2544.1.12.2.5 | ||||||||||||
| !f3BulkTrap | 1.3.6.1.4.1.2544.1.12.2.5.1 | ||||||||||||
notification · current This is the bulk trap sent by the agent for bulk operations. | |||||||||||||
Textual conventions
AffectedEntityINTEGERcard1(3)card2(4)none(1)notApplicable(0)shelf(2)Defines the affected Entity.
CallhomeStateINTEGERcompleted(1)failed(2)inProgress(3)notStarted(4)Describes States available for CallHome
CmAclFilterActionINTEGERdeny(2)permit(1)Enumerations for Access Control List permit - Permit access, deny - Deny access.
CmAutoProvModeINTEGERauto(3)confirm(2)off(1)Enumerations for Auto Provisioning Mode off - manual mode, confirm - auto provisioning with confirmation auto - true auto provisioning.
CmFileServicesModeINTEGERalarmlogfileupload(15)auditlogfileupload(16)configfiledownload(22)configfileupload(21)csrUpload(29)dbbackup(4)dbdownload(3)dbpropagate(17)dbrestore(5)dbupload(2)debugfileupload(13)defaultvalsfiledownload(23)idle(1)rebooting(12)rfc2544testreportupload(30)satresultupload(24)securitylogfileupload(14)sslcertificatedownload(25)sslencprivatekeydownload(27)sslkeypairdownload(28)sslprivatekeydownload(26)swcancelupgrade(10)swdownload(6)swinstall(7)swpropagate(18)swrevert(11)swupgrade(8)swvalidate(9)sysdiagfilesave(20)sysdiagfileupload(19)File Services Operation. idle - Idle and available. dbupload - Database upload in progress. dbdownload - Database download in progress. dbbackup - Database backup in progress. dbrestore - Database restore in progress. swdownload - Software download in progress. swinstall - Software install in progress. swupgrade - Software upgrade in progress. swvalidate - Software validation in progress. swcancelupgrade - Software upgrade cancelled. swrevert - Software upgrade reverted. rebooting - System rebooting. debugfileupload - Last Reset Cause debug file upload in progress. securitylogfileupload - Security log upload in progress alarmlogfileupload - Alarm log upload in progress auditlogfileupload - Audit log upload in progress dbpropagate - Database propagate in progress. swpropagate - Software propagate in progress. sysdiagfileupload - System diagnose file upload in progress. sysdiagfilesave - System diagnose file save in progress. configfileupload - Configuration file upload in progress. configfiledownload - Configuration file download in progress. defaultvalsfiledownload- Default Values file download in progress. satresultupload - SAT test result file upload in progress. sslcertificatedownload - SSL Certificate file download in progress. sslprivatekeydownload - SSL Private Key file download in progress. sslencprivatekeydownload - SSL Encrypted Private Key file download in progress. sslkeypairdownload - SSL Key Pair file download in progress. csrUpload - CSR Upload rfc2544testreportupload - Rfc2544 Test Report Upload
CmFileServicesStatusINTEGERbadarchive(18)cannot-revert(13)failure(17)file-not-found(4)in-progress(1)incompatarchive(19)install-failed(14)invalid-file-type(8)login-failed(3)no-space-left(7)no-sw-toinstall(10)nobackup-database(9)permission-denied(5)revert-failed(16)server-unreachable(6)success(2)sw-not-installed(11)swVersionNotApproved(20)upgrade-failed(15)validation-timer-notactive(12)Status of the user initiated file transfer. in-progress - File transfer / processing is in progress. success - File transfer and processing completed successfully. login-failed - Login failed. file-not-found - File not found. permission-denied - Permission denied. server-unreachable - Server unreachable. no-space-left - No space left on device. invalid-file-type - Invalid file type. nobackup-database - No backup database. no-sw-toinstall - No software to install. sw-not-installed - Software not installed. validation-timer-notactive - Validation timer not active. cannot-revert - Cannot revert. install-failed - Installation failed. upgrade-failed - Upgrade Failed. revert-failed - Revert failed. failure - Generic File transfer or processing failure. badarchive - Bad Archive. incompatarchive - Incompatible Archive.CmFileTransferMethodINTEGERftp(1)scp(2)sftp(3)tftp(5)web(4)Enumerations for File Transfer Methods ftp - FTP scp - SCP sftp- Secure FTP web - WEB based, this is a read-only. tftp- TFTP.
CmNtpModeINTEGERboth(3)client(1)ntp-peering(5)ntp-server-and-peering(4)server(2)Enumerations for NTP Types client, server, both, ntp-server-and-peering, ntp-peering .
CmNtpServerTypeINTEGERnot-applicable(0)primary(1)secondary(2)Enumerations for NTP Server Types primary secondary .
CmNtpTypeINTEGERunicast(1)Enumerations for NTP Types unicast multicast anycast .
CmRestartCauseTypeINTEGERbustxntimeout(6)buttonFactoryDefaultReset(9)buttonReset(8)hardware(7)hwwatchdogexpired(5)poweronreset(1)unrecoverablesysevent(4)unreoverableappevent(3)userinitiated(2)System Restart Cause Type. poweronreset - Interruption of power. userinitiated - User initiated such as software upgrade, restore database, restore system defaults, restore factory defaults unrecoverableappevent - Unrecoverable application event unrecoverablesysevent - Unrecoverable system event hwwatchdogexpired - Hardware watchdog expired bustxntimeout - Bus transaction timeout hardware - Hardware failure.CmVersionTypeINTEGERactive(1)staging(3)standby(2)Enumerations for Version Type active, standby.
F3ConfigFileActionINTEGERload-config(5)none(0)remove(3)restart-with-file(1)save-delta(2)save-full(4)Defines the actions on configuration file. none - Unused value restart-with-file - Restart the system; System will revert to using system defaults and will apply the specified configuration files on restart save-delta - Save delta configuration file : this generates a running config delta w.r.t the system defaults remove - Remove specified configuration file save-full - Save running configuration file and it will generate a full running config file load-config - Load specified delta config file without restarting.F3ConfigFileStatusINTEGERcompleted(3)failed(4)in-progress(2)initial(1)not-applicable(0)Defines the status of configuration file actions. initial - Initial status in-progress - Configuration File Operation is in progress completed - Configuration File Operation completed failed - Configuration File Operation failed
F3TargetAddressLifetimeINTEGERduration1day(2)duration1hour(1)duration1month(5)duration1week(4)duration3days(3)notApplicable(0)unlimited(6)Lifetime of target address.
FileTransferServerTypeINTEGERhostname(3)ipaddr(1)ipv6addr(2)url(4)Defines the file transfer server Type. ipaddr - server ipv4 address ipv6addr - server ipv6 address hostname - server host name URL - the URL of the remote server
LldpV2ConfigurationADVAExtMaxNeighborsActionINTEGERdelete-entry(1)discard-lldppdu(2)Discard: information selected to be discarded is the information in the current LLDPDU. Deleteentry:information selected to be discarded is currently in the LLDP remote systems MIB.NtpAuthKeyTypeINTEGERmd5(1)notApplicable(0)sha1(2)Defines the NTP Authentication Key Type.
PeerUpgradeReadyConditionINTEGERignorealarms(2)noalarms(5)nocriticalalarms(3)nomjandcrialarms(4)notApplicable(1)Defines the Peer Upgrade Ready Condition Entity.
PeerUpgradeStatusINTEGERinprogress(1)ready(2)Defines the Peer Upgrade Status Entity.
ServerConfigTypeINTEGERdhcp(1)userdefined(2)Defines the file transfer server Type. DHCP - Server is assigned by DHCP server USERDEFINED - server assinged with user configuration.
SysAuthKeyTypeINTEGERmd5(1)notApplicable(0)Defines the System Authentication Key Type.
SysLogFormatTypeINTEGERadva(1)rfc3164(2)Defines the Syslog Timestamp Format Type. ADVA - Adva Timestamp format RFC3164 - RFC3164 Timestamp format.
TimeOfDayTypeINTEGERlocal(1)ntp(2)ntpclock(5)ptp(3)timeclock(4)Defines the System Time Of Day Type. local - System time driven by local clock ntp - System time driven by NTP client ptp - System time driven by PTP Telecom Slave timeclock - System time driven by time clock ntpclock - System time driven by NTP server or peers
Traps / Notifications
- cmAttributeValueChangeTrap
1.3.6.1.4.1.2544.1.12.2.2.2 - cmObjectCreationTrap
1.3.6.1.4.1.2544.1.12.2.2.3 - cmObjectDeletionTrap
1.3.6.1.4.1.2544.1.12.2.2.4 - cmSnmpDyingGaspTrap
1.3.6.1.4.1.2544.1.12.2.2.5 - cmStateChangeTrap
1.3.6.1.4.1.2544.1.12.2.2.1 - f3BulkTrap
1.3.6.1.4.1.2544.1.12.2.5.1 - f3DatabaseSyncTrap
1.3.6.1.4.1.2544.1.12.2.2.6