ADIC-SANMGR-PROXY-MIB
Quantum Corporation (formerly 'Advanced Digital Information Corporation')This MIB provides Tape Library product information.
snmptranslate -m ADIC-SANMGR-PROXY-MIB -Tpsnmpwalk -v2c -c <community> -m ADIC-SANMGR-PROXY-MIB <host> 1.3.6.1.4.1.3764.1.1.400.10Imports
| ADIC-INTELLIGENT-STORAGE-MIB | Boolean, RowStatus, componentId, network |
|---|---|
| RFC1155-SMI | Gauge32 |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, enterprises, experimental, iso, private |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IsanmgrProxy | 1.3.6.1.4.1.3764.1.1.400.10 | |||
identity This MIB provides Tape Library product information. | ||||
| Npathlight | 1.3.6.1.4.1.3764.1.1.400.10.10 | |||
| Nagent | 1.3.6.1.4.1.3764.1.1.400.10.10.2 | |||
| TagentScalarTable | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1 | NA | mandatory | |
| RagentScalarEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory A component entry containing objects for a particular component.
| ||||
| CpaIdentify | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Flash the READY light on the SAN Data Gateway front panel. A non-zero value turns the LED on for the specified number of seconds. Zero turns LED off. | ||||
| CpaReboot | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.2 | Reset | RW | mandatory |
column · Reset · read-write · mandatory Writing a reboot(2) value here causes immediate reboot. | ||||
| CpaHealthCheckValue | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.3 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory Value in percent of health check tests passed. | ||||
| CpaHealthCheckLevel | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Scrutiny level of health check function.
| ||||
| CpaHealthCheckInterval | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.5 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Health Check interval in minutes. | ||||
| CpaEvRptLevel | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used when retrieving Event Log. Events with log level greater than paEvRptLevel are not retrieved.
| ||||
| CpaEventLogLevels | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.7 | OCTET STRING (SIZE (256)) | RW | mandatory |
column · OCTET STRING (SIZE (256)) · read-write · mandatory Each of 255 event types has an 8-bit level used when reading log. Currently valid LogLevel range is 0-3. | ||||
| CpaTrapThresholds | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.8 | OCTET STRING (SIZE (256)) | RW | mandatory |
column · OCTET STRING (SIZE (256)) · read-write · mandatory Each of 255 event types has an 8-bit threshold.
When the number of events exceeds the Trap Threshold,
a trap is generated and sent to all parties listed
in the trap destination table (also under SNMP
control) .
Threshold 0 means Never
Threshold 1 means Always
Threshold 2 - 255 means Number of events per
10 minute period | ||||
| CpaBaudRate | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Serial baud rate for SAN Gateway Service Port. Currently, the Agent does not support baud rate change: the rate is hard-coded to 19200 baud.
| ||||
| CpaFiller | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Filler field to the sanmanger MIB | ||||
| CpaLogSize | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.11 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Number of records in entire event log. (Not just current records since boot.) | ||||
| CpaCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used for issuing command to SNMP agent.
| ||||
| CpaLogBoot | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.13 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory Absolute index of first log entry at boot. | ||||
| CpaLogNCurrent | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.14 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory SNMP Get (read) returns number of records since boot subject to viewing level filtering. SNMP Set (write) copies this number of records since boot (subject to level filtering) into a buffer from which records are read. This mode of use is deprecated. The preferred way to get the event log since boot is to read paLogBoot, set paEvRptLevel and do a series of SNMP GetNext calls starting at instance paLogBoot until end of event log MIB table is reached. | ||||
| CpaLogChronFirst | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.15 | Gauge32 | RW | obsolete |
column · Gauge32 · read-write · obsolete Used to request range of records from paLogChronFirst to paLogChronLast | ||||
| CpaLogChronLast | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.16 | Gauge32 | RW | obsolete |
column · Gauge32 · read-write · obsolete Used to request range of records from paLogChronFirst to paLogChronLast | ||||
| CpaLogScroll | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.17 | INTEGER | RW | obsolete |
column · INTEGER · read-write · obsolete Used to request previous/next range of records event log | ||||
| CpaLogFilename | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.18 | DisplayString (SIZE (0..128)) | RW | mandatory |
column · DisplayString (SIZE (0..128)) · read-write · mandatory Used to save event log to a file. | ||||
| CpaEnvironmentState | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Temperature and Voltage Status of
SAN Data Gateway:
**********************************
(LSB) bit 0 Auxiliary Power
bit 1 Main Power
bit 2 Temperature Warning
bit 3 Temperature Alarm | ||||
| CpaGatewayFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.20 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory SAN Data Gateway Firmware Revision information. | ||||
| CpaGatewayHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.21 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory SAN Data Gateway Hardware Revision information. | ||||
| CpaSnmpFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.22 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory SNMP Agent Firmware Revision information. | ||||
| CpaRidTag | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.23 | DisplayString (SIZE (0..128)) | RO | mandatory |
column · DisplayString (SIZE (0..128)) · read-only · mandatory SAN Data Gateway RIDTag. | ||||
| CpaSerialNumber | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.24 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory SAN Data Gateway Serial Number. | ||||
| CpaServerVersion | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.25 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Remote Management software writes Server version information here to customize SNMP Agent behavior. | ||||
| CpaProductType | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.26 | PathlightProduct | RO | mandatory |
column · PathlightProduct · read-only · mandatory Type of SAN device | ||||
| CpaVPSEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.27 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory State of VPS Access Control enable. | ||||
| CpaLicenseKey | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.28 | DisplayString (SIZE (0..64)) | RW | mandatory |
column · DisplayString (SIZE (0..64)) · read-write · mandatory Used to pass feature enabling license keys. | ||||
| CpaThirdPartyCopyEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.29 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory State of Extended 3rd Party Copy enable. Enabled means that a valid license key has been entered for this feature. | ||||
| CpaVPSStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.30 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory State of Virtual Private SAN feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paVPSEnabled. Writing 1 to bit 0 makes VPS active if licensed. Writing 0 to bit 0 makes VPS inactive if licensed. | ||||
| CpaThirdPartyCopyStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.31 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory State of Extended 3rd Party Copy feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paThirdPartyCopyEnabled. Writing 1 to bit 0 makes Third Party Copy active if licensed. Writing 0 to bit 0 makes Third Party Copy inactive if licensed. | ||||
| CpaCommandControlLUN | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.32 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Gateway/Router Command and Control LUN | ||||
| CpaSanDirectorEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.33 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory State of SAN Director Support for this device. To enable, user must write a valid license key to OID paLicenseKey or enter the license key from the service port. | ||||
| CpaNodeName | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.34 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory SAN Gateway Node Name. | ||||
| CpaVPMStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.35 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory State of Virtual Private Map feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. | ||||
| CpaSRSStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.36 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory State of SAN Replication Services feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. | ||||
| CpaEthernetType | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.37 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Current Ethernet Speed. | ||||
| CpaTrapSequenceNumber | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Sequence number of last trap sent by this SNMP Agent. | ||||
| CpaSysNodeNameMode | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.39 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Algorithm used when computing Fibre Channel World Wide Node Name for each port. If the value is sameForEachPort(0), then the World Wide Node Name is the same for each port and computed based on the World Wide Node Name of the gateway. If the value is differentForEachPort(1), then the World Wide Node Name is different for each port, computed based on the World Wide Port Name for that port.
| ||||
| CpaGhostIOTimeToLive | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.40 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The amount of time that commands can remain queued in the SNC before being considered stale and discarded. 0 : Never discard (ghost I/O disabled) 1 - 30 : TTL in ticks (60th of a second) | ||||
| CpaMaxLun | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum LUN value possible. | ||||
| CpaEVPSEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.42 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bit 0: EVPS active if 1, inactive if 0 Bit 1: EVPS licensed if 1, unlicensed if 0 | ||||
| CpaMaxHostLun | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.43 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The number of devices one host can see | ||||
| CpaAMPStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.44 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Status of Automatic Multipath feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. | ||||
| CpaEnableAllScsiTargets | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.45 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to Enable/Disable all-scsi-targets.
| ||||
| CpaHPFStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.46 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bit 0: HPF active if 1, inactive if 0 Bit 1: HPF licensed if 1, unlicensed if 0 | ||||
| CpaSoip2iRescan | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.47 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Writing true(1) here causes SOIP2 initiator to rescan its bus. | ||||
| CpaSoipiRescan | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.48 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Writing true(1) here causes SOIP initiator to rescan its bus. | ||||
| CpaFLBStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.49 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Status of Load Balancing feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. | ||||
| CpaSoip2iScanPeriod | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.50 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SOIP2 Initiator Scan period in seconds. 0 will disable scan. | ||||
| CpaCommandFlowLogEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.51 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory Returns TRUE iff Command Flow Logging is availabe. Returns FALSE otherwise. | ||||
| TpaEventLog | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500 | NA | mandatory | |
table · not-accessible · mandatory Entry point for the Agent Event Log Table. | ||||
| RpaEventLogEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1 | NA | mandatory | |
| CpaIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory MIB EventLogEntry Table index. | ||||
| CpaTime | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.2 | TimeTicks | RO | mandatory |
column · TimeTicks · read-only · mandatory Time stamp (since boot). | ||||
| CpaProducer | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Numeric identifier for this event's producer. | ||||
| CpaEventClass | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Numeric identifier for this event's class. | ||||
| CpaEventCode | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Numeric code for this event. | ||||
| CpaSeq | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Sequence number (relative record number) since boot. | ||||
| CpaEventVars | 1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.7 | DisplayString (SIZE (0..256)) | RO | mandatory |
column · DisplayString (SIZE (0..256)) · read-only · mandatory Text description of event. | ||||
| Ndevices | 1.3.6.1.4.1.3764.1.1.400.10.10.3 | |||
| TpdDevices | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1 | NA | mandatory | |
table · not-accessible · mandatory Pathlight Physical Device Group *********************************** Each device attached to the Gateway has an entry here. | ||||
| RpdDevEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1 | NA | mandatory | |
| CpdIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory MIB table index | ||||
| CpdUID | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.2 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory Universal Identifier | ||||
| CpdType | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.3 | DeviceType | RO | mandatory |
column · DeviceType · read-only · mandatory Device Type i.e. disk/tape/cd etc. | ||||
| CpdVendor | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.4 | DisplayString (SIZE (8)) | RO | mandatory |
column · DisplayString (SIZE (8)) · read-only · mandatory Device Vendor | ||||
| CpdProduct | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.5 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory Device Product Identifier | ||||
| CpdBlockSize | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Block size in Bytes | ||||
| CpdCapacity | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.7 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory Capacity in BLOCKS (see pdBlockSize) | ||||
| CpdAccess | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Is device accessible ? | ||||
| CpdRemovable | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.9 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory Is device removable ? | ||||
| CpdStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.10 | PltStatus | RO | mandatory |
column · PltStatus · read-only · mandatory Device Status | ||||
| CpdSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Device Speed in MBytes/second | ||||
| CpdWidth | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Data path width in bits | ||||
| CpdSerial | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.13 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Device Serial Number | ||||
| CpdIdentify | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Number of seconds to flash identifying LED. Write here to flash LED on device if supported by Gateway and device. Zero turns LED off. | ||||
| CpdInterfaceType | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.15 | Interface | RO | mandatory |
column · Interface · read-only · mandatory This device's type of communication interface. | ||||
| CpdBus | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI bus number | ||||
| CpdId | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI Address ID | ||||
| CpdLun | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI Logical Unit Number. | ||||
| CpdCtlrIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Index of this device's controller in the Controllers MIB table and type-specific controller tables | ||||
| CpdHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.20 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Device hardware revision number/identifier | ||||
| CpdFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.21 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Device firmware revision number/identifier | ||||
| CpdReset | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.22 | Reset | RW | mandatory |
column · Reset · read-write · mandatory Generic device reset if supported. Write reset(1) here to reset device if supported by Gateway firmware and device. | ||||
| CpdStatusBits | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Device status bits as per SCSI spec. | ||||
| CpdScsiAnsiLevel | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.24 | ScsiAnsiLevel | RO | mandatory |
column · ScsiAnsiLevel · read-only · mandatory Device SCSI level. | ||||
| CpdTargetLun | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This target device's Logical Unit Number as seen from attached host. | ||||
| CpdIpAddress | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.26 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory This target device's IP Address if applicable. In case of SAN Gateway or Router, this information is used to allow arbitrary drill-down capability. | ||||
| CpdAltVendor | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.27 | DisplayString (SIZE (8)) | RO | mandatory |
column · DisplayString (SIZE (8)) · read-only · mandatory Device alternate Vendor | ||||
| CpdAltProduct | 1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.28 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory Device alternate Product Identifier | ||||
| Ncontrollers | 1.3.6.1.4.1.3764.1.1.400.10.10.4 | |||
| TpcControllers | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1 | NA | mandatory | |
table · not-accessible · mandatory Pathlight Controller Group ******************************* All controllers installed in the SAN Data Gateway have an entry here AND a parallel entry in the controller-type specific table (Fibre Channnel, SSA, or SCSI). | ||||
| RpcCtlrEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1 | NA | mandatory | |
| CpcIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory MIB Table index. | ||||
| CpcType | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.2 | Interface | RO | mandatory |
column · Interface · read-only · mandatory Communication Interface type. | ||||
| CpcVendorId | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.3 | VendorIDInt | RO | mandatory |
column · VendorIDInt · read-only · mandatory Integer vendor ID for this controller. | ||||
| CpcProductId | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Vendor's integer ID for this controller. | ||||
| CpcRevision | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.5 | DisplayString (SIZE (0..32)) | RO | deprecated |
column · DisplayString (SIZE (0..32)) · read-only · deprecated Revision information for this controller. See also pcHWRev and pcFWRev. | ||||
| CpcSubVendor | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Integer sub-vendor ID for this controller. | ||||
| CpcSubProduct | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Vendor's integer sub-product ID for this controller. | ||||
| CpcMaxBurst | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Maximum burst transfer rate in MBytes/second | ||||
| CpcLatency | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.9 | INTEGER (0..255) | RW | mandatory |
column · INTEGER (0..255) · read-write · mandatory Latency Timer in Clock Ticks. | ||||
| CpcIdentify | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Reserved for flashing identifying LED on device. | ||||
| CpcPCIBus | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory PCI Bus number in SAN Data Gateway for this controller. | ||||
| CpcPCIDev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory PCI device number in SAN Data Gateway for this controller. | ||||
| CpcPCIFunc | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory PCI Function number in SAN Data Gateway for this contoller. | ||||
| CpcReset | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.14 | Reset | RW | mandatory |
column · Reset · read-write · mandatory Generic controller reset variable. Not supported for all controller types. | ||||
| CpcRescan | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.15 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Writing true(1) here causes controller to rescan its bus if rescan is supported for this controller type. | ||||
| CpcLED | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.16 | OCTET STRING (SIZE (2)) | RO | mandatory |
column · OCTET STRING (SIZE (2)) · read-only · mandatory Is LED on? | ||||
| CpcHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.17 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Hardware revision for this controller. | ||||
| CpcFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.18 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Firmware revision for this controller | ||||
| CpcPCISlot | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Location of Channel Card on PCI bus | ||||
| CpcPMCSlot | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Location of Card: PMC 1, 2 or 3. 0=> Not a PMC card | ||||
| CpcPCIClass | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.21 | OCTET STRING (SIZE (3)) | RO | mandatory |
column · OCTET STRING (SIZE (3)) · read-only · mandatory Device class code as per PCI specification. | ||||
| CpcSplitMode | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.22 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Enable/Disable Split Mode for this controller. | ||||
| CpcChannelMask | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.23 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Specifies access permissions for this initiator
in bits 0 through 18
*************************************************
-* SCSI Channels *-
Bit 0 => Is access DISALLOWED to SCSI channel 1 ?
Bit 1 => Is access DISALLOWED to SCSI channel 2 ?
Bit 2 => Is access DISALLOWED to SCSI channel 3 ?
Bit 3 => Is access DISALLOWED to SCSI channel 4 ?
-* Ultra SCSI Channels *-
Bit 4 => Is access DISALLOWED to Ultra SCSI channel 1 ?
Bit 5 => Is access DISALLOWED to Ultra SCSI channel 2 ?
Bit 6 => Is access DISALLOWED to Ultra SCSI channel 3 ?
Bit 7 => Is access DISALLOWED to Ultra SCSI channel 4 ?
Bit 8 => Is access DISALLOWED to Ultra SCSI channel 5 ?
Bit 9 => Is access DISALLOWED to Ultra SCSI channel 6 ?
-* Fibre Channel *-
Bit 10 => Is access DISALLOWED to Fibre Channel 1 ?
Bit 11 => Is access DISALLOWED to Fibre Channel 2 ?
Bit 12 => Is access DISALLOWED to Fibre Channel 3 ?
Bit 13 => Is access DISALLOWED to Fibre Channel 4 ?
Bit 14 => Is access DISALLOWED to Fibre Channel 5 ?
Bit 15 => Is access DISALLOWED to Fibre Channel 6 ?
-* SSA Channels *-
Bit 16 => Is access DISALLOWED to SSA channel 1 ?
Bit 17 => Is access DISALLOWED to SSA Channel 2 ?
Bit 18 => Is access DISALLOWED to SSA Channel 3 ? | ||||
| CpcPortHostType | 1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.24 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Host type for this port. Used if VPS is not enabled. | ||||
| TpcFCCtlrs | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2 | NA | mandatory | |
table · not-accessible · mandatory Entry point for Fibre Channel Controller Device Group ****************************************************** This table parallels the Controller Table: a Fibre Channel controller with pcIndex N in the controller table appears here as index N as well, and in general there are rows in this table which are empty. | ||||
| RfcCtlrEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1 | NA | mandatory | |
row · not-accessible · mandatory Fibre Channel Controller Device table entry.
| ||||
| CfcStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.1 | FcStatus | RO | mandatory |
column · FcStatus · read-only · mandatory Status of the Fibre Channel Controller | ||||
| CfcMaxSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.2 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory Maximum Transfer Speed in MBytes per second. | ||||
| CfcWWID | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.3 | DisplayString (SIZE (17)) | RO | mandatory |
column · DisplayString (SIZE (17)) · read-only · mandatory World Wide Identifier for this Fibre Channel Controller. | ||||
| CfcFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.4 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Firmware revision number/identifier for this Fibre Channel Controller. | ||||
| CfcHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.5 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Hardware revision number/identifier for this Fibre Channel Controller. | ||||
| CfcLoopID | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.6 | INTEGER (-1..127) | RW | mandatory |
column · INTEGER (-1..127) · read-write · mandatory Fibre Channel Loop ID. soft = -1 | ||||
| CfcFrameSize | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Fibre Channel frame size. | ||||
| CfcPortType | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.8 | FibrePort | RW | mandatory |
column · FibrePort · read-write · mandatory Fibre Channel Port Type | ||||
| CfcMedia | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.9 | FibreMedia | RO | mandatory |
column · FibreMedia · read-only · mandatory Media type for this Fibre Channel Controller | ||||
| CfcSerialNumber | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.10 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Serial Number for this Fibre Channel Controller. | ||||
| CfcLoopIDMode | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.11 | FibreLoopIDMode | RO | mandatory |
column · FibreLoopIDMode · read-only · mandatory Fibre Channel Loop ID mode (soft or hard) | ||||
| CfcALPhysicalAddress | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Arbitrated Loop Physical Address (ALPA) | ||||
| CfcPortMode | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.13 | FibrePortMode | RW | mandatory |
column · FibrePortMode · read-write · mandatory Fibre Channel Port Mode. | ||||
| CfcConnectionOptions | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.14 | FibreConnOptions | RW | mandatory |
column · FibreConnOptions · read-write · mandatory Connection options for ISP2200 FC chip. Values 4 - 8 are reserved. | ||||
| CfcCtlrChipType | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Fibre Channel controller chip. Valid types are 2100, 2200 for QLogic ISP2100 and ISP2200 chips. | ||||
| CfcTapeFeature | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.16 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory Status of Fibre Channel Tape Specification support. true means this controller supports FC Tape false means this controller does not support FC Tape | ||||
| CfcHardID | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.17 | INTEGER (-1..256) | RW | mandatory |
column · INTEGER (-1..256) · read-write · mandatory Fibre Channel Hard ID, the preferred loop ID for this controller. Even if the controller is in Hard Loop ID mode, the actual loop ID is not guaranteed to be fcHardID. | ||||
| CfcCurrentSpeedSetting | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.18 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Speed in Gb/sec. 0: Auto, 1: 1Gb, 2: 2Gb | ||||
| CfcCurrentSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Current Speed Indicator Gb/sec. | ||||
| CfcFrameBufferSize | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Frame Buffer Size | ||||
| CfcLinkFailureCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Link Failure Count | ||||
| CfcLossSyncCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Loss of Sync Count | ||||
| CfcLossSignalCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Loss of Signal Count | ||||
| CfcProtocolErrorCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Primitive Sequence Protocol Error Count | ||||
| CfcInvalidTxWordCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Invalid Transmission Word Count | ||||
| CfcInvalidCRCCount | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Invalid CRC Count | ||||
| CfcWWNodeName | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.27 | DisplayString (SIZE (17)) | RO | mandatory |
column · DisplayString (SIZE (17)) · read-only · mandatory The World Wide Node Name for this Fibre Channel Controller. The Node Name for this port may computer strictly on the World Wide Node Name for the gateway, or on a per port basis which uses the World Wide Port Name (fcWWID), thus giving each port a different Node Name. See paSysNodeNameMode to get or set which algorithm is in use. | ||||
| CfcPortID | 1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fibre Channel Port Identifier 24 bit quantity which uniquely identifies the port within the loop or fabric. | ||||
| TpcSSACtlrs | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3 | NA | obsolete | |
table · not-accessible · obsolete Entry point for SSA Controller Device Group **************************************************** This table parallels the Controller Table: an SSA controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty. | ||||
| RssaCtlrEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1 | NA | obsolete | |
| CssaStatus1 | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.1 | PltStatus | RO | mandatory |
column · PltStatus · read-only · mandatory Status on port 1 of dual port SSA card | ||||
| CssaStatus2 | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.2 | PltStatus | RO | mandatory |
column · PltStatus · read-only · mandatory Status on port 2 of dual port SSA card | ||||
| CssaSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SSA transfer speed 80 Mbytes/second or 160 MBytes/second
| ||||
| CssaUID | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.4 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory Universal Identifier for this SSA Controller. | ||||
| CssaFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.5 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Firmware revision number/identifier for this SSA controller. | ||||
| CssaMaxTarg | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.6 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Maximum number of targets supported. | ||||
| CssaMaxInit | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.7 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Maximum number of initiators supported. | ||||
| CssaPathAlg | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SSA pathing algorithm.
| ||||
| CssaHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.9 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Hardware revision number/identifier for this SSA controller. | ||||
| CssaMasterPriority | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.10 | INTEGER (0..7) | RO | mandatory |
column · INTEGER (0..7) · read-only · mandatory The SSA Master Priority of an SSA node is a number from 0 to 7. SSA initiators elect a master based on this priority. If more than one SSA node has the same priority then the node with the highest UID is elected. Pathlight SSA host adapters default to a Master Priority of 4. SAN Gateway SSA Target adapters default to a priority of 5 to ensure that the Gateway node will be master in a multi-initiator loop. This value should never be set to 7 because this is the priority used to guarantee mastership to a node that is entering Service Mode. | ||||
| CssaSATAQuota | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.11 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory The SSA SAT Quota A parameter is an 8 bit number that determines 'the maximum number of frames which can be originated from this port before the port is SATisfied and forwards the SAT character. A value of zero means that no SATs are forwarded or issued from this port.' | ||||
| CssaSATBQuota | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.12 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory The SSA SAT Quota B parameter is an 8 bit number that determines 'the maximum number of frames which this port can originate without forwarding a SAT character. A value of zero means that an infinite number of frames can be sent without being subject to SAT pacing.' | ||||
| CssaSATIQuota | 1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.13 | INTEGER (0..255) | RO | mandatory |
| TpcSCSICtlrs | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4 | NA | mandatory | |
table · not-accessible · mandatory Entry point for SCSI Controller Device Group **************************************************** This table parallels the Controller Table: a SCSI controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty. | ||||
| RscsiCtlrEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1 | NA | mandatory | |
| CscsiStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.1 | PltStatus | RO | mandatory |
column · PltStatus · read-only · mandatory Status for this SCSI controller. | ||||
| CscsiSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.2 | ScsiSpeed | RW | mandatory |
column · ScsiSpeed · read-write · mandatory SCSI Transaction speed. | ||||
| CscsiRole | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Is this a Target or an Initiator ?
| ||||
| CscsiHostId | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.4 | INTEGER (0..15) | RW | mandatory |
column · INTEGER (0..15) · read-write · mandatory Host ID defaults to 7. | ||||
| CscsiMaxSpeed | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.5 | ScsiSpeed | RW | mandatory |
column · ScsiSpeed · read-write · mandatory Maximum Speed of this SCSI Channel. | ||||
| CscsiTerm | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory State of internal SCSI bus terminations, if any.
| ||||
| CscsiIoCard | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.7 | ScsiCardType | RO | mandatory |
column · ScsiCardType · read-only · mandatory Type of SCSI controller hardware. | ||||
| CscsiMaxIds | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Maximum Number of IDs for this SCSI controller. | ||||
| CscsiMaxLuns | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Maximum Number of LUNs for this SCSI controller. | ||||
| CscsiMaxWidth | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Maximum transfer width in bits. | ||||
| CscsiHWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.11 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Hardware revision for this SCSI controller. | ||||
| CscsiFWRev | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.12 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Firmware revision for this SCSI controller. | ||||
| CscsiResetOnPowerUp | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.13 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Enables/Disables SCSI bus reset upon Gateway power-up for this SCSI controller. | ||||
| CscsiMultiInitEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.14 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Enables/Disables multi-initiator support on for this SCSI controller. | ||||
| CscsiAlternateHostId | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.15 | INTEGER (-1..15) | RW | mandatory |
column · INTEGER (-1..15) · read-write · mandatory Alternate Host ID for this SCSI controller. -1 means use automatic. | ||||
| CscsiTargetEnabled | 1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.16 | Boolean | RO | mandatory |
column · Boolean · read-only · mandatory Indicates target ScsiRole support for this SCSI controller. | ||||
| Nnotification | 1.3.6.1.4.1.3764.1.1.400.10.10.5 | |||
| TpnTrapDest | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1 | NA | obsolete | |
table · not-accessible · obsolete Trap destination Group Table ****************************************** A list of IP addresses to which SNMP Traps are sent in parallel using UDP Port 162. | ||||
| RpnTrapDestEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1 | NA | obsolete | |
| CpnIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.1 | INTEGER | RW | obsolete |
column · INTEGER · read-write · obsolete Index into TrapDest table | ||||
| CpnIPAddr | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.2 | IpAddress | RW | obsolete |
column · IpAddress · read-write · obsolete IP Address of destination entity to which traps are sent. | ||||
| CpnUdpPort | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.3 | INTEGER (0..65535) | RW | obsolete |
column · INTEGER (0..65535) · read-write · obsolete UDP Port on which traps are sent to this entity. | ||||
| CpnTrapStyle | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.4 | INTEGER | RW | obsolete |
column · INTEGER · read-write · obsolete Style to be used when building a trap PDU to be sent to this entity. A value of proprietary(1) selects the proprietary format used by the Pathlight SAN Director management application. A value of rfc1215(2) selects the format as described in the RFC 1215 TRAP-TYPE objects included in this MIB document. The default is proprietary(1).
| ||||
| CpnTrapBroadcastMode | 1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to Enable/Disable the broadcasting of traps.
| ||||
| NpanelLED | 1.3.6.1.4.1.3764.1.1.400.10.10.6 | |||
| NpaHost | 1.3.6.1.4.1.3764.1.1.400.10.10.7 | |||
| ThostCommandTable | 1.3.6.1.4.1.3764.1.1.400.10.10.7.1 | NA | mandatory | |
| RhostCommandEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.7.1.1 | NA | mandatory | |
row · not-accessible · mandatory An object for issuing host-related commands to the SNC.
| ||||
| ChostCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.7.1.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to issue commands to VPS control
software. Possible commands are:
commitChanges: commits any pending
LUN Mapping changes to persistent
memory.
| ||||
| ThostInitiator | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2 | NA | mandatory | |
table · not-accessible · mandatory Attached Host Group Table *************************** List of attached hosts and pertinent information. | ||||
| RhostInitiatorEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1 | NA | mandatory | |
| ChostIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Index into Host Initiator table. | ||||
| ChostRowStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Row Status for this row. | ||||
| ChostWWName | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.3 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory World Wide name of this Initiator. | ||||
| ChostName | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.4 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Name for this Initiator. | ||||
| ChostType | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.5 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Operating System and other host environment information. | ||||
| ChostPortID | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.6 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Host port identifcation. | ||||
| ChostSANConnection | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SAN Connection (1-6) to which this host is connected. | ||||
| ChostConnectionType | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.8 | Interface | RO | mandatory |
column · Interface · read-only · mandatory Type of data connection (FCAL, etc.) | ||||
| ChostITLData | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.9 | OCTET STRING (SIZE (256)) | RW | mandatory |
column · OCTET STRING (SIZE (256)) · read-write · mandatory ITL Access Control data for this host. 256 possible LUNs with one Byte of data per LUN. | ||||
| ChostIPAddr | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.10 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory IP Address of this host. Host is not required to have an IP address. | ||||
| ChostLunType | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.11 | HostLUNType | RW | mandatory |
column · HostLUNType · read-write · mandatory The type of this host for EVPS. 8-bit, 16-bit, or volume set | ||||
| ChostLunMap | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.12 | OCTET STRING (SIZE (512)) | RW | mandatory |
column · OCTET STRING (SIZE (512)) · read-write · mandatory EVPS Map data. 256 possible LUNs with two Bytes of data for each lun | ||||
| ChostInbandAccess | 1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The in-band access level of the host | ||||
| NscsiMap | 1.3.6.1.4.1.3764.1.1.400.10.10.8 | |||
| TscsiMapCommandTable | 1.3.6.1.4.1.3764.1.1.400.10.10.8.1 | NA | mandatory | |
table · not-accessible · mandatory SCSI Map Command Table | ||||
| RscsiMapCommandEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.8.1.1 | NA | mandatory | |
row · not-accessible · mandatory An object for issuing VPM-related commands to the SNC.
| ||||
| CscsiMapCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.8.1.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to issue commands to SCSI Channel map (VPM) routines. | ||||
| TscsiChannelMap | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2 | NA | mandatory | |
table · not-accessible · mandatory SCSI Channel Device Map Table ****************************** List of devices presented to SCSI attached initiator. The initiator sees a series of (Target ID, LUN ) SCSI targets which are mapped to a logical device identified by a Pathlight assigned LUN. | ||||
| RscsiMapEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1 | NA | mandatory | |
row · not-accessible · mandatory SCSI Channel Device Map Table entry.
| ||||
| CscsiMapRowStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.1 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory Specifies the state of the row. | ||||
| CscsiMapPort | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI port (bus) number for this entry (1 thru 10). | ||||
| CscsiMapTid | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI Target ID for this entry. | ||||
| CscsiMapLun | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SCSI LUN for this entry. | ||||
| CscsiMapAssignedLun | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Pathlight LUN assigned to this entry. This assigned LUN maps to some device connected to the Gateway/Router by some other means (FC, SSA, SCSI, ...). | ||||
| CscsiMapComments | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.6 | DisplayString (SIZE (0..80)) | RW | mandatory |
column · DisplayString (SIZE (0..80)) · read-write · mandatory User's comments for this entry. | ||||
| CscsiMapPdIndex | 1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Index into Pathlight SANMgr MIB Device Table ( pd group ). The Device Table has more detailed information about attached devices. | ||||
| NdeviceMap | 1.3.6.1.4.1.3764.1.1.400.10.10.9 | |||
| TdeviceMapCommandTable | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1 | NA | mandatory | |
| RdeviceMapCommandEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1 | NA | mandatory | |
row · not-accessible · mandatory An object for issuing VPM-related commands to the SNC.
| ||||
| CdeviceMapCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to issue commands to device map map routines.
| ||||
| CdeviceMapMultipathMode | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to set the Multipath mode.
| ||||
| CdeviceMapRemoveDevice | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.3 | INTEGER | WO | mandatory |
column · INTEGER · write-only · mandatory Used to remove a device from the Device Map given its Device-Id. Warning: This command stops the IO for this device before removing | ||||
| CdeviceLoadBalancingMode | 1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to set the Load Balancing Mode.
| ||||
| TdmDeviceMap | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2 | NA | mandatory | |
table · not-accessible · mandatory Device Map Group *********************************** Each device attached to the Gateway has an entry here. Historical data of devices not presently connected may also appear here. | ||||
| RdmDevMapEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1 | NA | mandatory | |
| CdmRowStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.1 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory Row Control Object for this row | ||||
| CdmAssignedLun | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Logical Unit Number assigned to this attached device. Range is 0 thru 255. | ||||
| CdmType | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.3 | Interface | RW | mandatory |
column · Interface · read-write · mandatory Type of device (FC, SCSI, SNA, SSA). | ||||
| CdmPort | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SAN Gateway Port to which this device is connected. May be 1 thru 10 for SCSI, 1 thru 6 for Fibre Channel, 1 thru 3 for SSA. | ||||
| CdmTargetId | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Target ID of the attached target device. This is the actual target ID of the device, not fabricated by the Gateway or Router. | ||||
| CdmTargetLun | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Logical Unit Number of the attached target device. This is the actual LUN of the device, not fabricated by the Gateway or Router. | ||||
| CdmUid | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.7 | OCTET STRING (SIZE (8)) | RW | mandatory |
column · OCTET STRING (SIZE (8)) · read-write · mandatory A universally unique identifier for this target device. | ||||
| CdmPath | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Multipath Mode of the device. The
mode can only be single(0), manual(1),
or auto(1).
| ||||
| CdmSerialNum | 1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.9 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory The Serial Number of the device. | ||||
| Nreplication | 1.3.6.1.4.1.3764.1.1.400.10.10.10 | |||
| TsrsDevTable | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1 | NA | mandatory | |
table · not-accessible · mandatory Entry point for SAN Replication Service Device Group ***************************************************** Each SAN Replication Service Device has an entry in this table | ||||
| RsrsDevEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1 | NA | mandatory | |
row · not-accessible · mandatory SAN Replication Service Device Group entry.
| ||||
| CsrsDevId | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Device ID for this SRS Device. | ||||
| CsrsDevState | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of this LUN Replicated Device.
| ||||
| CsrsDevCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to invoke SAN Replication Services API commands. Parameters may be passed in the same SNMP Set varbind list with the srsDevCommand as the last varbind. ********************************************* create(1) - Creates a new SRS Device delete(2) - Deletes an existing SRS Device
| ||||
| CsrsDevAssignedLun | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Assigned LUN of the SAN Replication Service Device's Primary. | ||||
| CsrsDevMemberCount | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of members of this LUN Replicated Device. | ||||
| CsrsDevMembersOnline | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of members online. | ||||
| CsrsDevFlags | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SCSI device flags for this SAN Replication Service Device. | ||||
| CsrsDevSizeInBlocks | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.8 | Gauge32 | RW | mandatory |
column · Gauge32 · read-write · mandatory Size in blocks of this SAN Replication Services Device. | ||||
| CsrsDevBlockSize | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Block size in octets. | ||||
| CsrsDevPrimary | 1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Assigned LUN of this SRS Device's Primary. | ||||
| TsrsMemTable | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2 | NA | mandatory | |
table · not-accessible · mandatory Entry point for SAN Replication Services Member Group ***************************************************** This table lists the Members of each SRS Device. | ||||
| RsrsMemEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1 | NA | mandatory | |
row · not-accessible · mandatory SAN Replication Services Member Group entry.
| ||||
| CsrsMemDeviceId | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Device ID of the SAN Replication Services Device to which this member belongs. | ||||
| CsrsMemId | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Member ID (index) of this member device. | ||||
| CsrsMemState | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of this SAN Replication Services Device Member.
| ||||
| CsrsMemCommand | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to invoke SAN Replication Services API methods. Parameters may be passed in the same SNMP Set varbind list with the lrmCommand as the last varbind.
| ||||
| CsrsMemType | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Is this device a primary or secondary member.
| ||||
| CsrsMemSyncPoint | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of blocks synchronized so far. Used for monitoring synchronization. | ||||
| CsrsMemAssignedLun | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Assigned LUN for this SRS Member. | ||||
| CsrsMemReadOptions | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SRS Member read options.
| ||||
| CsrsMemWriteOptions | 1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SRS Member write options.
| ||||
| NenvData | 1.3.6.1.4.1.3764.1.1.400.10.10.11 | |||
| TenvDataTable | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1 | NA | mandatory | |
table · not-accessible · mandatory Entry point for Environmental Data Group ***************************************************** This table lists the attributes of each environmental data. | ||||
| RenvDataEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1 | NA | mandatory | |
| CenvDataId | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Event identifier. | ||||
| CenvDataName | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.2 | DisplayString (SIZE (0..64)) | RO | mandatory |
column · DisplayString (SIZE (0..64)) · read-only · mandatory Name of this environmental data | ||||
| CenvNominalLo | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.3 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Minimum value for Nominal status Warning state occurs if the current value is less than this | ||||
| CenvNominalHi | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.4 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Maximum Value for Nominal status Warning state occurs if the current value is greater than this. | ||||
| CenvWarningLo | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.5 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Minimum value for Warning status Alarm state occurs if the current value is less than this | ||||
| CenvWarningHi | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.6 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Maximum Value for Warning status Alarm state occurs if the current value is greater than this. | ||||
| CenvCurValue | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.7 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Current Value. | ||||
| CenvCurStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.8 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Current Status: Nominal, Warning, or Alarm. | ||||
| CenvUnit | 1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.9 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Unit | ||||
| NportFailover | 1.3.6.1.4.1.3764.1.1.400.10.10.12 | |||
| NfcHostPortFailover | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1 | |||
| TfcHPFPortMappings | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1 | NA | mandatory | |
table · not-accessible · mandatory FC Host Port Failover Mapping *********************************** This table consists of port mappings for the FC Host Port Failover | ||||
| RfcHPFMapEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory SNMP table for FC Host Port Failover Mappings | ||||
| CfcHPFMapRowStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.1 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory Row Control Object for this row | ||||
| CfcHPFMapVirtualPort | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The virtual port index. Depends on the configuration. Usaually same as phys port index, but 0 if not configured | ||||
| CfcHPFMapPrimaryPort | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The physical port index that acts as the default standby | ||||
| CfcHPFMapStandbyList | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.4 | OCTET STRING (SIZE (256)) | RW | mandatory |
column · OCTET STRING (SIZE (256)) · read-write · mandatory The comma seperated list of ports that are configured as standbys for the virtual port, excluding the primary port. | ||||
| CfcHPFMapActivePort | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The physical port thats active on this virtual port | ||||
| TfcHPFPhysicalPorts | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2 | NA | mandatory | |
table · not-accessible · mandatory FC Host Port Failover Physical Ports *************************************** This table consists of physical port settings for the FC Host Port Failover | ||||
| RfcHPFPhysicalPortEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1 | NA | mandatory | |
row · not-accessible · mandatory SNMP table for FC Host Port Failover Port Settings
| ||||
| CfcHPFPhysicalPortRowStatus | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.1 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory Row Control Object for this row | ||||
| CfcHPFPhysicalPort | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The physical FC port Index. The range depends on the pathlight model. | ||||
| CfcHPFPhysicalPortFailureType | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.3 | FcHPFPortFailType | RO | mandatory |
column · FcHPFPortFailType · read-only · mandatory If this phys port failed, this field gives the type of failure.Values 0 = None, 1 = Link Down 2 = Link Error | ||||
| CfcHPFPhysicalPortCurrentState | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.4 | FcHPFPortState | RO | mandatory |
column · FcHPFPortState · read-only · mandatory The current state of this physical port. The values 0 = Online, 1 = Offline | ||||
| CfcHPFPhysicalPortIntervention | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.5 | Boolean | RW | mandatory |
column · Boolean · read-write · mandatory Does this physical port require intervention? Values 1 = true, 2 = false | ||||
| TfcHPFGlobalTable | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3 | NA | mandatory | |
table · not-accessible · mandatory FC Host Port Failover Global Settings **************************************** This table consists of settings global to the HPF function. | ||||
| RfcHPFGlobalEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1 | NA | mandatory | |
row · not-accessible · mandatory SNMP table for FC Host Port Failover Global Settings
| ||||
| CfcHPFLinkDownThreshold | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to set the Link Down threshold in seconds. Only after this delay the failover triggers | ||||
| CfcHPFErrorRecoveryMode | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.2 | FcHPFRecoveryType | RW | mandatory |
column · FcHPFRecoveryType · read-write · mandatory Used to set the global recovery mode for failures that happen due to FC cable errors Values: returnToActive(0), returnToStandby(1), requiresIntervention(2) | ||||
| CfcHPFLinkDownRecoveryMode | 1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.3 | FcHPFRecoveryType | RW | mandatory |
column · FcHPFRecoveryType · read-write · mandatory Used to set the global recovery mode for failures that happen due to Link Down Errors Values: returnToActive(0), returnToStandby(1), requiresIntervention(2) | ||||
| NutilityModule | 1.3.6.1.4.1.3764.1.1.400.10.10.13 | |||
| TutilityModuleTable | 1.3.6.1.4.1.3764.1.1.400.10.10.13.1 | NA | mandatory | |
table · not-accessible · mandatory Entry point for Utility Module Group ***************************************************** | ||||
| RutilityModuleEntry | 1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1 | NA | mandatory | |
| CutilityModuleId | 1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Utility module index. | ||||
| CutilityModuleVersion | 1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1.2 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory Utility module version identifier. | ||||
| NtrapDefinition | 1.3.6.1.4.1.3764.1.1.400.10.10.1000 | |||
| !ssaPortUpEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.1 | |||
notification An SSA Port Up Event has occurred. | ||||
| !ssaPortDownEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.2 | |||
notification An SSA Port Down Event has occurred. | ||||
| !ssaUidAddedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.3 | |||
notification An SSA UID Added Event has occurred. | ||||
| !ssaUidRemovedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.4 | |||
notification An SSA UID Removed Event has occurred. | ||||
| !ssaWebReconfiguredEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.5 | |||
notification An SSA Web Reconfigured Event has occurred. | ||||
| !ssaAsyncErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.6 | |||
notification An SSA Async Error Event has occurred. | ||||
| !ssaAdapterEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.7 | |||
notification An SSA Adapter Event has occurred. | ||||
| !senseDataEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.8 | |||
notification Sense Data recorded following a check condition. Normally, the host system will request and process sense data, and then perform error recovery. | ||||
| !unitAttentionEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.9 | |||
notification A LUN reports a unit attention condition on a non-removable media device. | ||||
| !ibfEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.10 | |||
notification An Internal Bus Fault event has occurred. | ||||
| !temperatureChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.11 | |||
notification A temperature sensor has reported a change from one of three possible states to a another. The possible states are OK, High, Very High. The display string contained in the varbind paEventVars indicates the initial and final temperature state. | ||||
| !timeReferenceEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.12 | |||
notification | ||||
| !shutdownEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.13 | |||
notification This unit is shutting down as a result of a restart request. | ||||
| !diagnosticEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.14 | |||
notification This event is used for diagnostic purposes. | ||||
| !configurationEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.15 | |||
notification | ||||
| !unexpectedScsiInterruptEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.16 | |||
notification A SCSI bus reports an unexpected interrupt. | ||||
| !lipResetEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.17 | |||
notification A Fibre Channel interface reports a LIP reset was received from a host. | ||||
| !fcSystemErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.18 | |||
notification A Fibre Channel interace reports a system error. | ||||
| !fcRequestTransferErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.19 | |||
notification A Fibre Channel interface reports an error processing a request. | ||||
| !fcResponseTransferErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.20 | |||
notification A Fibre Channel interface reports an error processing a response. | ||||
| !memoryFaultEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.21 | |||
notification Processor memory fault detected. | ||||
| !fcLipEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.22 | |||
notification A Fibre Channel interface detected a LIP. | ||||
| !fcLoopUpEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.23 | |||
notification A Fibre Channel interface reports loop up. | ||||
| !fcLoopDownEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.24 | |||
notification A Fibre Channel interface reports loop down. | ||||
| !pciBusParityErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.25 | |||
notification Parity error detected on unit internal PCI bus. | ||||
| !pciInterfaceErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.26 | |||
notification Interface error detected on unit internal PCI bus. | ||||
| !scsiDeviceAddedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.27 | |||
notification A device has been added to a SCSI bus. | ||||
| !scsiBusResetEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.28 | |||
notification A SCSI interface reports a bus reset was detected. | ||||
| !deviceAddedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.29 | |||
notification This unit has added a device to its configuration table. Note: This trap is held off until the unit has been up for 60 seconds. | ||||
| !deviceRemovedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.30 | |||
notification This unit has removed a device from its configuration table. | ||||
| !loggingStartedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.31 | |||
notification Event logging service has started. | ||||
| !loggingStoppedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.32 | |||
notification Event logging service has stopped. | ||||
| !interfaceBusFaultEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.33 | |||
notification An interface has detected a bus fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault. | ||||
| !interfaceDeviceFaultEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.34 | |||
notification An interface has detected a device fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault. | ||||
| !scsiUnexpectedDisconnectEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.35 | |||
notification A SCSI interface has reported an unexpected disconnect by a device. | ||||
| !scsiParityErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.36 | |||
notification A SCSI interface has detected a parity error on the bus. | ||||
| !fcPortDatabaseChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.37 | |||
notification Fibre Channel port databse change detected. | ||||
| !ddfMemoryErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.38 | |||
notification An error was detected on the Direct Data Flow memory board. | ||||
| !fcDirectoryServerChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.39 | |||
notification The Directory Server on the Fibre Channel fabric has changed. | ||||
| !lunLimitExcededEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.40 | |||
notification The maximum LUN limit has been exceded, too many devices connected. | ||||
| !fcTransferFailureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.41 | |||
notification Fibre Channel transfer error. | ||||
| !deviceLimitExcededEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.42 | |||
notification The maximum device limit has been exceded, the persistent device map database is full. | ||||
| !fcDebugDumpEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.43 | |||
notification A Fibre Channel interface driver has reported a a debug dump. | ||||
| !excessiveScsiBusErrorsEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.44 | |||
notification | ||||
| !memoryScrubberErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.45 | |||
notification | ||||
| !srsDeviceCreatedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.46 | |||
notification A new SAN Replication Services device has been created | ||||
| !srsDeviceOnlineEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.47 | |||
notification A SAN Replication Services device has entered the online state. | ||||
| !srsDeviceRemovedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.48 | |||
notification A SAN Replication Services device has been removed (deleted). | ||||
| !srsDeviceFailedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.49 | |||
notification A SAN Replication Services device has failed. | ||||
| !srsMemberAddedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.50 | |||
notification A new member LUN has been added to a SAN Replication Services device. | ||||
| !srsMemberSuspendedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.51 | |||
notification A SAN Replication Services member has been suspended. | ||||
| !srsMemberRemovedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.52 | |||
notification A SAN Replication Services member has been removed. | ||||
| !srsMemberSyncStartedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.53 | |||
notification A SAN Replication Service member has begun synchronization to the primary member. | ||||
| !srsMemberSyncDoneEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.54 | |||
notification A SAN Replication Service member has completed synchronization to the primary member. | ||||
| !srsMemberSyncErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.55 | |||
notification An error was detect during synchronization of a SAN Replication Service member to the primary member. | ||||
| !srsMemberRetryEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.56 | |||
notification A command issued to a SAN Replication Services member has failed and is being retried. | ||||
| !srsMemberErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.57 | |||
notification A command issued to a SAN Replication Services member has resulted in an error. | ||||
| !envPowerNominalEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.58 | |||
notification Power has returned to nominal state from a warning or alarm state. | ||||
| !envPowerWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.59 | |||
notification Power has entered a warning state from a nominal state (power degrading) or alarm state (power improving). | ||||
| !envPowerAlarmEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.60 | |||
notification Power has entered an alarm state. | ||||
| !envTemperatureNominalEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.61 | |||
notification Inlet air, outlet air, or I/O processor temperature has returned to nominal state from a warning or alarm state. | ||||
| !envInletTemperatureWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.62 | |||
notification Inlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing). | ||||
| !envInletTemperatureAlarmEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.63 | |||
notification Inlet air temperature has entered an alarm state. | ||||
| !envOutletTemperatureWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.64 | |||
notification Outlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing). | ||||
| !envOutletTemperatureAlarmEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.65 | |||
notification Outlet air temperature has entered an alarm state. | ||||
| !envFanNominalEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.66 | |||
notification Fan has entered a nominal state from a fault state. | ||||
| !envFanWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.67 | |||
notification Fan has entered a warning range (tachometer fans only). | ||||
| !envFanAlarmEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.68 | |||
notification Fan has entered an alarm range (tachometer fans) or is stalled (rotor stall fans). | ||||
| !eccMemoryErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.69 | |||
notification Error correcting code memory has detected an error. | ||||
| !restartCompleteEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.70 | |||
notification Restart process has completed. | ||||
| !firmwareUploadCompleteEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.71 | |||
notification Firmware upload process has completed. | ||||
| !maxInitiatorsExceededEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.72 | |||
notification Maximum number of initiators has been exceeded. | ||||
| !dataPathFailoverEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.73 | |||
notification | ||||
| !amemWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.74 | |||
notification Amem memory not properly installed. | ||||
| !hostOfflineEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.75 | |||
notification An attached host has been moved to the offline state. | ||||
| !hostOnlineEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.76 | |||
notification An attached host has been moved to the online state. | ||||
| !hostPortFailoverEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.77 | |||
notification | ||||
| !hpfRequiresInterventionEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.78 | |||
notification Host port failover requires invention. | ||||
| !controllerResetCompletedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.79 | |||
notification The controller indicated in paEventVars has completed its reset sequence. The text format for paEventVars is: NOTICE: FC Controller %d Restart Complete | ||||
| !controllerStatusChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.80 | |||
notification The status of the controller indicated in paEventVars has changed. The controller index (pcIndex) and the new status (fcStatus for Fibre Channel, scsiStatus for SCSI) are encoding in paEventVars according to the following format: NOTICE: Controller %d status is %d | ||||
| !ethFailoverEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.81 | |||
notification Ethernet Port Filover has occured. | ||||
| !memUsageWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.82 | |||
notification Memory usage reached warning level. | ||||
| !taskSuspendedWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.83 | |||
notification Task suspended warning. | ||||
| !umTaskWatchdogWarningEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.84 | |||
notification Utility module task watchdog warning. | ||||
| !dataPathTrespassEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.85 | |||
notification Data path trespass has occurred. | ||||
| !deviceListChangedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.86 | |||
notification Target device list changed on an interface. | ||||
| !autoLevelStart | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.87 | |||
notification Auto Level has begun. | ||||
| !autoLevelEnd | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.88 | |||
notification Auto Level is done. | ||||
| !autoLevelError | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.89 | |||
notification Auto Level has got error. | ||||
| !corruptNVRAMError | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.90 | |||
notification NVRAM corruption detected. | ||||
| !powerSupplyOutOfSpecEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.100 | |||
notification The main power supply voltage is out of specified operating range. | ||||
| !auxPowerOutOfSpecEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.101 | |||
notification The auxillary power supply voltage is out of specified operating range. | ||||
| !newTemperatureChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.102 | |||
notification Temperature change detected since last report. The possible temperature states are OK, High, and Very High. | ||||
| !newPciErrorsEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.103 | |||
notification | ||||
| !newMemoryParityErrorsEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.104 | |||
notification | ||||
| !pciBusInterfaceErrorEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.105 | |||
notification | ||||
| !fcInterfaceFailureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.106 | |||
notification Fibre Channel interface failed Health Check. | ||||
| !scsiInterfaceFailureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.107 | |||
notification SCSI interface failed Health Check. | ||||
| !ssaInterfaceFailureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.108 | |||
notification SSA interface failed Health Check. | ||||
| !deviceFailureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.109 | |||
notification Target device failed Health Check. | ||||
| !fcLinkStatusChangeEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.110 | |||
notification Fibre Channel link status has changed. | ||||
| !newFcTranferErrorsEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.111 | |||
notification New Fibre Channel transfer errors were detected since last report. | ||||
| !envFanEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.112 | |||
notification The health check task has detected a fan running in warning or alarm range. | ||||
| !envPowerEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.113 | |||
notification The health check task has detected a power supply running in warning or alarm range. | ||||
| !envTemperatureEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.114 | |||
notification The health check task has detected a temperature sensor reporting in warning or alarm range. | ||||
| !eccMemoryHealthCheckEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.115 | |||
notification The health check task has detected an ECC memory error. | ||||
| !eccMemoryScrubberEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.116 | |||
notification The health check task has detected an ECC memory scrubber event. | ||||
| !deviceRecoverEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.118 | |||
notification | ||||
| !logWillOverwriteEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.150 | |||
notification The event log circular buffer is about to wrap, overwriting the oldest entries.
| ||||
| !bootCompletedEvent | 1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.4444 | |||
notification This unit has completed its boot sequence and is ready for SNMP communication with management applications. During the time period between the initiation of the boot (or reboot) sequence and the issuing of the bootCompletedEvent trap, certain data objects may not be completely initialized. As such, management applications should not attempt to retrieve data via SNMP until the bootCompletedEvent is issued.
| ||||
Traps / Notifications
- amemWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.74 - autoLevelEnd
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.88 - autoLevelError
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.89 - autoLevelStart
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.87 - auxPowerOutOfSpecEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.101 - bootCompletedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.4444 - configurationEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.15 - controllerResetCompletedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.79 - controllerStatusChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.80 - corruptNVRAMError
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.90 - dataPathFailoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.73 - dataPathTrespassEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.85 - ddfMemoryErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.38 - deviceAddedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.29 - deviceFailureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.109 - deviceLimitExcededEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.42 - deviceListChangedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.86 - deviceRecoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.118 - deviceRemovedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.30 - diagnosticEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.14 - eccMemoryErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.69 - eccMemoryHealthCheckEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.115 - eccMemoryScrubberEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.116 - envFanAlarmEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.68 - envFanEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.112 - envFanNominalEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.66 - envFanWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.67 - envInletTemperatureAlarmEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.63 - envInletTemperatureWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.62 - envOutletTemperatureAlarmEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.65 - envOutletTemperatureWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.64 - envPowerAlarmEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.60 - envPowerEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.113 - envPowerNominalEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.58 - envPowerWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.59 - envTemperatureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.114 - envTemperatureNominalEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.61 - ethFailoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.81 - excessiveScsiBusErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.44 - fcDebugDumpEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.43 - fcDirectoryServerChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.39 - fcInterfaceFailureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.106 - fcLinkStatusChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.110 - fcLipEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.22 - fcLoopDownEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.24 - fcLoopUpEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.23 - fcPortDatabaseChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.37 - fcRequestTransferErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.19 - fcResponseTransferErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.20 - fcSystemErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.18 - fcTransferFailureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.41 - firmwareUploadCompleteEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.71 - hostOfflineEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.75 - hostOnlineEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.76 - hostPortFailoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.77 - hpfRequiresInterventionEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.78 - ibfEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.10 - interfaceBusFaultEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.33 - interfaceDeviceFaultEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.34 - lipResetEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.17 - logWillOverwriteEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.150 - loggingStartedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.31 - loggingStoppedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.32 - lunLimitExcededEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.40 - maxInitiatorsExceededEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.72 - memUsageWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.82 - memoryFaultEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.21 - memoryScrubberErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.45 - newFcTranferErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.111 - newMemoryParityErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.104 - newPciErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.103 - newTemperatureChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.102 - pciBusInterfaceErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.105 - pciBusParityErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.25 - pciInterfaceErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.26 - powerSupplyOutOfSpecEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.100 - restartCompleteEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.70 - scsiBusResetEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.28 - scsiDeviceAddedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.27 - scsiInterfaceFailureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.107 - scsiParityErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.36 - scsiUnexpectedDisconnectEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.35 - senseDataEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.8 - shutdownEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.13 - srsDeviceCreatedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.46 - srsDeviceFailedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.49 - srsDeviceOnlineEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.47 - srsDeviceRemovedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.48 - srsMemberAddedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.50 - srsMemberErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.57 - srsMemberRemovedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.52 - srsMemberRetryEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.56 - srsMemberSuspendedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.51 - srsMemberSyncDoneEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.54 - srsMemberSyncErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.55 - srsMemberSyncStartedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.53 - ssaAdapterEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.7 - ssaAsyncErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.6 - ssaInterfaceFailureEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.108 - ssaPortDownEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.2 - ssaPortUpEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.1 - ssaUidAddedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.3 - ssaUidRemovedEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.4 - ssaWebReconfiguredEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.5 - taskSuspendedWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.83 - temperatureChangeEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.11 - timeReferenceEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.12 - umTaskWatchdogWarningEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.84 - unexpectedScsiInterruptEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.16 - unitAttentionEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.0.9