Xdsl2Band INTEGERdownstream(2) ds1(4) ds2(6) ds3(8) ds4(10) upstream(1) us0(3) us1(5) us2(7) us3(9) us4(11)
Identifies a band in a VDSL2/ADSL/ADSL2/ADSL2+ link.
For a band in the upstream direction, transmission is from the
remote end (xTU-R) towards the central office end (xTU-C).
For a band in the downstream direction, transmission is from
the xTU-C towards the xTU-R.
For ADSL, ADSL2 and ADSL2+, which use a single band in the
upstream direction and a single band
in the downstream direction,
the only relevant values are upstream(1) and downstream(2).
For VDSL2, which uses multiple bands in each transmission
direction, a band in the upstream direction is indicated by any
of us0(3), us1(5), us2(7), us3(9), or us4(11), and a band in
the downstream direction is indicated by any of ds1(4),
ds2(6), ds3(8), or ds4(10).
For VDSL2, the values upstream(1) and downstream(2) may be used
when there is a need to refer to the whole upstream or
downstream traffic (e.g., report the average signal-to-noise
ratio on any transmission direction).
Specified as an INTEGER, the values are defined as
follows:
Xdsl2BandUs INTEGERus1(5) us2(7) us3(9) us4(11)
Each value identifies a specific band in the upstream
transmission direction (excluding the US0 band.).
The possible values that identify a band are as follows:
us1(5) - Upstream band number 1 (US1).
us2(7) - Upstream band number 2 (US2).
us3(9) - Upstream band number 3 (US3).
us4(11) - Upstream band number 4 (US4).
Xdsl2BitsAlloc OCTET STRING (SIZE (0..256))This type specifies an array of nibbles, where each nibble
indicates the bits allocation for a subcarrier.
Each nibble has a value in the range 0 to 15 to indicate
the bits allocation.
Xdsl2BpscResult INTEGERfailed(5) inProgress(3) noResources(6) none(1) success(2) unsupported(4)
Possible failure reasons associated with performing
a bits per subcarrier measurement on a DSL line.
Possible values are:
none (1) - The default value, in case a measurement
was never requested for the associated
line.
success (2) - The recent measurement request completed
successfully.
inProgress (3) - The bits per subcarrier measurement is
in progress.
unsupported (4) - The bits per subcarrier request
mechanism is not supported.
failed (5) - The measurement request has failed and no
results are available.
noResources (6) - The NE cannot initiate the command, due
to lack of internal memory resources.Xdsl2CarMask OCTET STRING (SIZE (0..128))This type defines an array of bands. Each band is
represented by 4 octets and there is a maximum of 32 bands
allowed.
Each band consists of a 16-bit start subcarrier index followed by
a 16-bit stop subcarrier index.
The subcarrier index is an unsigned number in the range 0 to
NSC-1.
Xdsl2ChAtmStatus BitslossOfCellDelineation(2) noCellDelineation(1) noDefect(0)
Objects with this syntax are status parameters that
reflect the failure status for the Transmission Convergence (TC)
layer of a given ATM interface (data path over a VDSL2/ADSL/
ADSL2 or ADSL2+ link).
This BITS structure can report the following failures:
noDefect (0) - This bit position positively
reports that no defect or failure
exists.
noCellDelineation (1) - The link was successfully
initialized, but cell delineation
was never acquired on the
associated ATM data path.
lossOfCellDelineation (2)- Loss of cell delineation on the
associated ATM data path.Xdsl2ChInitPolicy INTEGERpolicy0(1) policy1(2)
This syntax serves for channel configuration parameters
that reference the channel initialization policy.
The possible values are:
policy0 (1) - Policy 0 according to the applicable standard.
policy1 (2) - Policy 1 according to the applicable
standard.Xdsl2ChInpReport INTEGERinpComputedUsingFormula(1) inpEstimatedByXtur(2)
This type is used to indicate the method used to compute the
Actual Impulse Noise Protection (ACTINP). If set to
'inpComputedUsingFormula', the ACTINP is computed
according to the INP_no_erasure formula (9.6/G.993.2).
If set to 'inpEstimatedByXtur', the ACTINP is the value
estimated by the xTU receiver.
inpComputedUsingFormula (1) - ACTINP computed using
INP_no_erasure formula.
inpEstimatedByXtur (2) - ACTINP estimated by
the xTU receiver.Xdsl2ChPtmStatus BitsnoDefect(0) outOfSync(1)
Objects with this syntax are status parameters that
reflect the failure status for a given PTM interface (packet
data path over a VDSL2/ADSL/ADSL2 or ADSL2+ link).
This BITS structure can report the following failures:
noDefect (0) - This bit position positively
reports that no defect or failure exists.
outOfSync (1) - Out of synchronization.Xdsl2ConfPmsForce INTEGERl0orL2toL3(3) l0toL2(2) l3toL0(0)
Objects with this syntax are configuration parameters
that specify the desired power management state transition
for the VDSL2/ADSL/ADSL2 or ADSL2+ link.
In VDSL2, only L0 and L3 states are defined:
l3toL0 (0) - Perform a transition from L3 to L0
(Full power management state).
l0toL2 (2) - Perform a transition from L0 to L2
(Low power management state).
l0orL2toL3 (3) - Perform a transition into L3 (Idle
power management state).Xdsl2Direction INTEGERdownstream(2) upstream(1)
Identifies the direction of a band in a VDSL2/ADSL/ADSL2/
ADSL2+ link.
The upstream direction is a transmission from the remote end
(xTU-R) towards the central office end (xTU-C). The downstream
direction is a transmission from the xTU-C towards the xTU-R.
Specified as an INTEGER, the values are defined as
follows:
Xdsl2InitResult INTEGERcommFail(3) configError(1) configNotFeasible(2) noFail(0) noPeerAtu(4) otherCause(5)
Specifies the result of full initialization attempt; the
six possible result values are:
noFail (0) - Successful initialization
configError (1) - Configuration failure
configNotFeasible (2) - Configuration details not supported
commFail (3) - Communication failure
noPeerAtu (4) - Peer ATU not detected
otherCause (5) - Other initialization failure reason
Xdsl2LastTransmittedState INTEGERatucComb1(2) atucComb2(4) atucComb3(8) atucEct(16) atucExchmarker(25) atucG9941(0) atucIComb2(9) atucIcomb1(5) atucLineprob(6) atucMedley(24) atucMsg1(21) atucMsg2(26) atucMsgfmt(10) atucMsgpcb(11) atucParams(29) atucQuiet1(1) atucQuiet2(3) atucQuiet3(7) atucQuiet4(12) atucReverb1(13) atucReverb2(15) atucReverb3(17) atucReverb4(19) atucReverb5(22) atucReverb6(27) atucReverb7(30) atucSegue1(20) atucSegue2(23) atucSegue3(28) atucSegue4(31) atucShowtime(32) atucTref1(14) atucTref2(18) aturComb1(102) aturComb2(104) aturComb3(108) aturEct(117) aturExchmarker(124) aturG9941(100) aturIcomb1(105) aturIcomb2(109) aturLineprob(106) aturMedley(123) aturMsg1(122) aturMsg2(125) aturMsgfmt(110) aturMsgpcb(111) aturParams(128) aturQuiet1(101) aturQuiet2(103) aturQuiet3(107) aturQuiet4(113) aturQuiet5(115) aturReverb1(112) aturReverb2(114) aturReverb3(116) aturReverb4(118) aturReverb5(120) aturReverb6(126) aturReverb7(129) aturSegue1(119) aturSegue2(121) aturSegue3(127) aturSegue4(130) aturShowtime(131) vtucChDiscov1(202) vtucChDiscov2(208) vtucEct(214) vtucG9941(200) vtucMedley(219) vtucPeriodic1(206) vtucPeriodic2(216) vtucPilot1(204) vtucPilot2(212) vtucPilot3(215) vtucQuiet1(201) vtucQuiet2(205) vtucShowtime(221) vtucSynchro1(203) vtucSynchro2(207) vtucSynchro3(209) vtucSynchro4(211) vtucSynchro5(218) vtucSynchro6(220) vtucTeq(213) vtucTraining1(210) vtucTraining2(217) vturChDiscov1(302) vturChDiscov2(307) vturEct(314) vturG9941(300) vturLineprobe(304) vturMedley(318) vturPeriodic1(305) vturPeriodic2(315) vturQuiet1(301) vturQuiet2(309) vturQuiet3(313) vturShowtime(320) vturSynchro1(303) vturSynchro2(306) vturSynchro3(308) vturSynchro4(311) vturSynchro5(317) vturSynchro6(319) vturTeq(312) vturTraining1(310) vturTraining2(316)
This parameter represents the last successful transmitted
initialization state in the last full initialization performed
on the line. States are per the specific xDSL technology and
are numbered from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime.
Xdsl2LdsfResult INTEGERaborted(6) adminUp(9) cannotRun(5) failed(7) illegalMode(8) inProgress(3) noResources(11) none(1) success(2) tableFull(10) unsupported(4)
Possible failure reasons associated with performing
Dual Ended Loop Test (DELT) on a DSL line.
Possible values are:
none (1) - The default value in case LDSF was never
requested for the associated line.
success (2) - The recent command completed
successfully.
inProgress (3) - The Loop Diagnostics process is in
progress.
unsupported (4) - The NE or the line card doesn't support
LDSF.
cannotRun (5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted (6) - The Loop Diagnostics process aborted.
failed (7) - The Loop Diagnostics process failed.
illegalMode (8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp (9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull (10)- The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources (11)- The NE cannot initiate the command, due
to lack of internal memory resources.Xdsl2LineBpsc INTEGERidle(1) measure(2)
Objects with this syntax are configuration parameters
that control the bits per subcarrier measurement for a
VDSL2/ADSL/ADSL2 or ADSL2+ link. The possible values are:
idle (1) - Idle state
measure (2) - Measure the bits per subcarrier
Xdsl2LineCeFlag BitsenableCyclicExtension(0)
This type is used to enable the use of the optional
cyclic extension values. If the bit is set to '1', the optional
cyclic extension values may be used. Otherwise, the cyclic
extension shall be forced to the mandatory length (5N/32).
enableCyclicExtension (0) - Enable use of optional
Cyclic Extension values.Xdsl2LineClassMask INTEGERa998ORb997M1cORc998B(2) b997M1xOR998co(3) b997M2x(4) b998AdeM2x(7) b998M1x(5) b998M2x(6) bHpeM1(8) none(1)
VDSL2 PSD Mask Class.
The limit Power Spectral Density masks are grouped in
the following PSD mask classes:
Class 998 Annex A: D-32, D-48, D-64, D-128.
Class 997-M1c Annex B: 997-M1c-A-7.
Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M.
Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M,
997E17-M2x-NUS0, 997E30-M2x-NUS0.
Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0.
Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B,
998-M2x-NUS0, 998E17-M2x-NUS0,
998E17-M2x-NUS0-M, 998E30-M2x-NUS0,
998E30-M2x-NUS0-M.
Class 998ADE-M2x Annex B: Annex B: 998-M2x-A, 998-M2x-M,
998-M2x-B, 998-M2x-NUS0,
998ADE17-M2x-A, 998ADE17-M2x-B,
998ADE17-M2x-NUS0-M,
998ADE30-M2x-NUS0-A,
998ADE30-M2x-NUS0-M.
Class 998-B Annex C: POTS-138b, POTS-276b per C.2.1.1
in G.993.2, TCM-ISDN per C.2.1.2
in G.993.2.
Class 998-CO Annex C: POTS-138co, POTS-276co per C.2.1.1
in G.993.2.
Class HPE-M1 Annex B: HPE17-M1-NUS0, HPE30-M1-NUS0.Xdsl2LineLdsf INTEGERforce(1) inhibit(0)
Objects with this syntax are configuration parameters
that control the Loop Diagnostic mode for a VDSL2/ADSL/ADSL2
or ADSL2+ link. The possible values are:
inhibit (0) - Inhibit Loop Diagnostic mode
force (1) - Force/Initiate Loop Diagnostic mode
Xdsl2LineLimitMask Bitsprofile12Limit1(16) profile12Limit10(25) profile12Limit11(26) profile12Limit12(27) profile12Limit13(28) profile12Limit14(29) profile12Limit15(30) profile12Limit16(31) profile12Limit2(17) profile12Limit3(18) profile12Limit4(19) profile12Limit5(20) profile12Limit6(21) profile12Limit7(22) profile12Limit8(23) profile12Limit9(24) profile17Limit1(32) profile17Limit10(41) profile17Limit11(42) profile17Limit12(43) profile17Limit13(44) profile17Limit14(45) profile17Limit15(46) profile17Limit16(47) profile17Limit2(33) profile17Limit3(34) profile17Limit4(35) profile17Limit5(36) profile17Limit6(37) profile17Limit7(38) profile17Limit8(39) profile17Limit9(40) profile30Limit1(48) profile30Limit10(57) profile30Limit11(58) profile30Limit12(59) profile30Limit13(60) profile30Limit14(61) profile30Limit15(62) profile30Limit16(63) profile30Limit2(49) profile30Limit3(50) profile30Limit4(51) profile30Limit5(52) profile30Limit6(53) profile30Limit7(54) profile30Limit8(55) profile30Limit9(56) profile8Limit1(0) profile8Limit10(9) profile8Limit11(10) profile8Limit12(11) profile8Limit13(12) profile8Limit14(13) profile8Limit15(14) profile8Limit16(15) profile8Limit2(1) profile8Limit3(2) profile8Limit4(3) profile8Limit5(4) profile8Limit6(5) profile8Limit7(6) profile8Limit8(7) profile8Limit9(8)
The G.993.2 limit PSD mask for each class of profile.
The profiles are grouped in following profile classes:
- Class 8: Profiles 8a, 8b, 8c, 8d.
- Class 12: Profiles 12a, 12b.
- Class 17: Profile 17a.
- Class 30: Profile 30a.
Xdsl2LinePmMode BitsallowTransitionsToIdle(0) allowTransitionsToLowPower(1)
Objects with this syntax are configuration parameters
that reference the power modes/states into which the xTU-C or
xTU-R may autonomously transit.
It is a BITS structure that allows control of the following
transit options:
allowTransitionsToIdle (0) - xTU may autonomously transit
to idle (L3) state.
allowTransitionsToLowPower (1)- xTU may autonomously transit
to low-power (L1/L2)
state.Xdsl2LineProfiles Bitsprofile12a(4) profile12b(5) profile17a(6) profile30a(7) profile8a(0) profile8b(1) profile8c(2) profile8d(3)
Objects with this syntax reference the list of
ITU-T G.993.2 implementation profiles supported by an
xTU, enabled on the VDSL2 line or active on that line.
Xdsl2LinePsdMaskSelectUs INTEGERadlu32Eu32(1) adlu36Eu36(2) adlu40Eu40(3) adlu44Eu44(4) adlu48Eu48(5) adlu52Eu52(6) adlu56Eu56(7) adlu60Eu60(8) adlu64Eu64(9)
This type is used to define which upstream PSD mask is
enabled. This type is used only for Annexes J and M of ITU-T
Recommendations G.992.3 and G.992.5.
adlu32Eu32 (1), - ADLU-32 / EU-32
adlu36Eu36 (2), - ADLU-36 / EU-36
adlu40Eu40 (3), - ADLU-40 / EU-40
adlu44Eu44 (4), - ADLU-44 / EU-44
adlu48Eu48 (5), - ADLU-48 / EU-48
adlu52Eu52 (6), - ADLU-52 / EU-52
adlu56Eu56 (7), - ADLU-56 / EU-56
adlu60Eu60 (8), - ADLU-60 / EU-60
adlu64Eu64 (9) - ADLU-64 / EU-64
Xdsl2LineReset INTEGERidle(1) reset(2)
This type is used to request a line reset to occur.
idle (1) - This state indicates that there is
currently no request for a line reset.
reset (2) - This state indicates that a line reset
request has been issued.Xdsl2LineSnrMode INTEGERvirtualNoiseDisabled(1) virtualNoiseEnabled(2)
This type is used to enable the transmitter-referred
virtual noise. The value of 1, indicates that virtual
noise is disabled. The value of 2, indicates that virtual
noise is enabled.
virtualNoiseDisabled (1) - virtual noise is disabled.
virtualNoiseEnabled (2) - virtual noise is enabled.
Xdsl2LineStatus BitsinitFailure(4) lossOfFraming(1) lossOfPower(3) lossOfSignal(2) noDefect(0)
Objects with this syntax are status parameters
that reflect the failure status for a given endpoint of a
VDSL2/ADSL/ADSL2 or ADSL2+ link.
This BITS structure can report the following failures:
noDefect (0) - This bit position positively reports
that no defect or failure exist.
lossOfFraming (1) - Loss of frame synchronization.
lossOfSignal (2) - Loss of signal.
lossOfPower (3) - Loss of power. Usually this failure may
be reported for CPE units only.
initFailure (4) - Recent initialization process failed.
Never active on xTU-R.Xdsl2LineTxRefVnDs OCTET STRING (SIZE (0..96))This is a structure that represents up to 32 PSD mask
breakpoints.
Each breakpoint occupies 3 octets: The first two octets hold the
index of the subcarrier associated with the breakpoint. The
third octet holds the PSD reduction at the breakpoint from 0
(-140 dBm/Hz) to 200 (-40 dBm/Hz) using units of 0.5 dBm/Hz.
A special value of 255 indicates a noise level of 0 W/Hz.
The subcarrier index is an unsigned number in the range 0 to
NSCds-1.
Xdsl2LineTxRefVnUs OCTET STRING (SIZE (0..48))This is a structure that represents up to 16 PSD mask
breakpoints.
Each breakpoint occupies 3 octets: The first two octets hold the
index of the subcarrier associated with the breakpoint. The
third octet holds the PSD reduction at the breakpoint from 0
(-140 dBm/Hz) to 200 (-40 dBm/Hz) using units of 0.5 dBm/Hz.
A special value of 255 indicates a noise level of 0 W/Hz.
The subcarrier index is an unsigned number in the range 0 to
NSCus-1.
Xdsl2LineUs0Disable Bitsprofile12Us0Disable1(16) profile12Us0Disable10(25) profile12Us0Disable11(26) profile12Us0Disable12(27) profile12Us0Disable13(28) profile12Us0Disable14(29) profile12Us0Disable15(30) profile12Us0Disable16(31) profile12Us0Disable2(17) profile12Us0Disable3(18) profile12Us0Disable4(19) profile12Us0Disable5(20) profile12Us0Disable6(21) profile12Us0Disable7(22) profile12Us0Disable8(23) profile12Us0Disable9(24) profile17Us0Disable1(32) profile17Us0Disable10(41) profile17Us0Disable11(42) profile17Us0Disable12(43) profile17Us0Disable13(44) profile17Us0Disable14(45) profile17Us0Disable15(46) profile17Us0Disable16(47) profile17Us0Disable2(33) profile17Us0Disable3(34) profile17Us0Disable4(35) profile17Us0Disable5(36) profile17Us0Disable6(37) profile17Us0Disable7(38) profile17Us0Disable8(39) profile17Us0Disable9(40) profile30Us0Disable1(48) profile30Us0Disable10(57) profile30Us0Disable11(58) profile30Us0Disable12(59) profile30Us0Disable13(60) profile30Us0Disable14(61) profile30Us0Disable15(62) profile30Us0Disable16(63) profile30Us0Disable2(49) profile30Us0Disable3(50) profile30Us0Disable4(51) profile30Us0Disable5(52) profile30Us0Disable6(53) profile30Us0Disable7(54) profile30Us0Disable8(55) profile30Us0Disable9(56) profile8Us0Disable1(0) profile8Us0Disable10(9) profile8Us0Disable11(10) profile8Us0Disable12(11) profile8Us0Disable13(12) profile8Us0Disable14(13) profile8Us0Disable15(14) profile8Us0Disable16(15) profile8Us0Disable2(1) profile8Us0Disable3(2) profile8Us0Disable4(3) profile8Us0Disable5(4) profile8Us0Disable6(5) profile8Us0Disable7(6) profile8Us0Disable8(7) profile8Us0Disable9(8)
Indicates if US0 is disabled for each limit PSD mask.
The profiles are grouped in following profile classes:
- Class 8: Profiles 8a, 8b, 8c, 8d.
- Class 12: Profiles 12a, 12b.
- Class 17: Profile 17a.
- Class 30: Profile 30a.
Xdsl2LineUs0Mask Bitsadlu128(25) adlu32(16) adlu36(17) adlu40(18) adlu44(19) adlu48(20) adlu52(21) adlu56(22) adlu60(23) adlu64(24) eu128(9) eu32(0) eu36(1) eu40(2) eu44(3) eu48(4) eu52(5) eu56(6) eu60(7) eu64(8) reserved1(10) reserved10(29) reserved11(30) reserved12(31) reserved2(11) reserved3(12) reserved4(13) reserved5(14) reserved6(15) reserved7(26) reserved8(27) reserved9(28)
The US0 PSD masks to be allowed by the near-end xTU on
the line. This parameter is only defined for G.993.2 Annex A.
It is represented as a bitmap (0 if not allowed and 1 if
allowed) with the following definitions.
Xdsl2MaxBer INTEGEReminus3(1) eminus5(2) eminus7(3)
Objects with this syntax are configuration parameters
that reference the maximum Bit Error Rate (BER).
The possible values are:
eminus3 (1) - Maximum BER=E^-3
eminus5 (2) - Maximum BER=E^-5
eminus7 (3) - Maximum BER=E^-7
Xdsl2MrefPsdDs OCTET STRING (SIZE (0..192))Objects with this syntax are MEDLEY Reference PSD status
parameters in the downstream direction. This is expressed as
the set of
breakpoints exchanged at initialization.
The OCTET STRING contains up to 48 pairs of values in the
following structure:
Octets 0-1 -- Index of the first subcarrier used in the
context of a first breakpoint.
Octets 2-3 -- The PSD level for the subcarrier indicated
in octets 0-1.
Octets 4-7 -- Same, for a second breakpoint
Octets 8-11 -- Same, for a third breakpoint
And so on until
Octets 188-191 -- Same, for a 48th breakpoint.
The subcarrier index is an unsigned number in the range 0
to NSCds-1.
The PSD level is an integer value in the 0 to 4095 range. It is
represented in units of 0.1 dB offset from -140 dBm/Hz.Xdsl2MrefPsdUs OCTET STRING (SIZE (0..128))Objects with this syntax are MEDLEY Reference PSD status
parameters in the upstream direction. This is expressed
as the set of
breakpoints exchanged at initialization.
The OCTET STRING contains up to 32 pairs of values in the
following structure:
Octets 0-1 -- Index of the first subcarrier used in the
context of a first breakpoint.
Octets 2-3 -- The PSD level for the subcarrier indicated
in octets 0-1.
Octets 4-7 -- Same, for a second breakpoint
Octets 8-11 -- Same, for a third breakpoint
And so on until
Octets 124-127 -- Same, for a 32nd breakpoint.
The subcarrier index is an unsigned number in the range 0
to NSCus-1.
The PSD level is an integer value in the 0 to 4095 range. It is
represented in units of 0.1 dB offset from -140 dBm/Hz.Xdsl2OperationModes INTEGERansit1413(2) defMode(1) etsi(3) g9921IsdnNonOverlapped(6) g9921PotsNonOverlapped(4) g9921PotsOverlapped(5) g9921isdnOverlapped(7) g9921tcmIsdnNonOverlapped(8) g9921tcmIsdnOverlapped(9) g9921tcmIsdnSymmetric(14) g9922potsNonOverlapped(10) g9922potsOverlapped(11) g9922tcmIsdnNonOverlapped(12) g9922tcmIsdnOverlapped(13) g9923AnnexIAllDigNonOverlapped(30) g9923AnnexIAllDigOverlapped(31) g9923AnnexJAllDigNonOverlapped(32) g9923AnnexJAllDigOverlapped(33) g9923AnnexLMode1NonOverlapped(36) g9923AnnexLMode2NonOverlapped(37) g9923AnnexLMode3Overlapped(38) g9923AnnexLMode4Overlapped(39) g9923AnnexMPotsNonOverlapped(40) g9923AnnexMPotsOverlapped(41) g9923IsdnNonOverlapped(22) g9923PotsNonOverlapped(20) g9923PotsOverlapped(21) g9923isdnOverlapped(23) g9924AnnexIAllDigNonOverlapped(34) g9924AnnexIAllDigOverlapped(35) g9924potsNonOverlapped(26) g9924potsOverlapped(27) g9925AnnexIAllDigNonOverlapped(48) g9925AnnexIAllDigOverlapped(49) g9925AnnexJAllDigNonOverlapped(50) g9925AnnexJAllDigOverlapped(51) g9925AnnexMPotsNonOverlapped(52) g9925AnnexMPotsOverlapped(53) g9925IsdnNonOverlapped(44) g9925PotsNonOverlapped(42) g9925PotsOverlapped(43) g9925isdnOverlapped(45) g9932AnnexA(58) g9932AnnexB(59) g9932AnnexC(60)
The VDSL2 management model specified includes an xDSL Mode
object that identifies an instance of xDSL Mode-Specific
PSD Configuration object in the xDSL Line Profile. The
following classes of xDSL operating mode are defined.
The notes (F) and (L) denote Full-Rate and Lite/splitterless,
respectively:
+-------+--------------------------------------------------+
| Value | xDSL operation mode description |
+-------+--------------------------------------------------+
1 - The default/generic PSD configuration. Default
configuration will be used when no other matching
mode-specific configuration can be found.
2 - Regional Std. (ANSI T1.413) (F)
3 - Regional Std. (ETSI DTS/TM06006) (F)
4 - G.992.1 POTS non-overlapped (F)
5 - G.992.1 POTS overlapped (F)
6 - G.992.1 ISDN non-overlapped (F)
7 - G.992.1 ISDN overlapped (F)
8 - G.992.1 TCM-ISDN non-overlapped (F)
9 - G.992.1 TCM-ISDN overlapped (F)
10 - G.992.2 POTS non-overlapped (L)
11 - G.992.2 POTS overlapped (L)
12 - G.992.2 with TCM-ISDN non-overlapped (L)
13 - G.992.2 with TCM-ISDN overlapped (L)
14 - G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1
15-19 - Unused. Reserved for future ITU-T specification.
20 - G.992.3 POTS non-overlapped (F)
21 - G.992.3 POTS overlapped (F)
22 - G.992.3 ISDN non-overlapped (F)
23 - G.992.3 ISDN overlapped (F)
24-25 - Unused. Reserved for future ITU-T specification.
26 - G.992.4 POTS non-overlapped (L)
27 - G.992.4 POTS overlapped (L)
28-29 - Unused. Reserved for future ITU-T specification.
30 - G.992.3 Annex I All-Digital non-overlapped (F)
31 - G.992.3 Annex I All-Digital overlapped (F)
32 - G.992.3 Annex J All-Digital non-overlapped (F)
33 - G.992.3 Annex J All-Digital overlapped (F)
34 - G.992.4 Annex I All-Digital non-overlapped (L)
35 - G.992.4 Annex I All-Digital overlapped (L)
36 - G.992.3 Annex L POTS non-overlapped, mode 1,
wide U/S (F)
37 - G.992.3 Annex L POTS non-overlapped, mode 2,
narrow U/S(F)
38 - G.992.3 Annex L POTS overlapped, mode 3,
wide U/S (F)
39 - G.992.3 Annex L POTS overlapped, mode 4,
narrow U/S (F)
40 - G.992.3 Annex M POTS non-overlapped (F)
41 - G.992.3 Annex M POTS overlapped (F)
42 - G.992.5 POTS non-overlapped (F)
43 - G.992.5 POTS overlapped (F)
44 - G.992.5 ISDN non-overlapped (F)
45 - G.992.5 ISDN overlapped (F)
46-47 - Unused. Reserved for future ITU-T specification.
48 - G.992.5 Annex I All-Digital non-overlapped (F)
49 - G.992.5 Annex I All-Digital overlapped (F)
50 - G.992.5 Annex J All-Digital non-overlapped (F)
51 - G.992.5 Annex J All-Digital overlapped (F)
52 - G.992.5 Annex M POTS non-overlapped (F)
53 - G.992.5 Annex M POTS overlapped (F)
54-57 - Unused. Reserved for future ITU-T specification.
58 - G.993.2 Annex A
59 - G.993.2 Annex B
60 - G.993.2 Annex CXdsl2PowerMngState INTEGERl0(1) l1(2) l2(3) l3(4)
Objects with this syntax uniquely identify each power
management state defined for the VDSL2/ADSL/ADSL2 or ADSL2+
link.
In VDSL2, only L0 and L3 states are defined.
The possible values are:
l0(1) - L0: Full power. Synchronized and
full transmission (i.e., Showtime).
l1(2) - L1: Low power with reduced net data rate
(for G.992.2 only).
l2(3) - L2: Low power with reduced net data rate
(for G.992.3, G.992.4 and G.992.5).
l3(4) - L3: Idle power management state / No
power.Xdsl2PsdMaskDs OCTET STRING (SIZE (0..96))This is a structure that represents up to 32 PSD mask
breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the subcarrier associated with the
breakpoint. The third octet holds the PSD reduction at the
breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units
of 0.5 dBm/Hz.
The subcarrier index is an unsigned number in the range 0 to
NSCds-1.
Xdsl2PsdMaskUs OCTET STRING (SIZE (0..48))This is a structure that represents up to 16 PSD mask
breakpoints.
Each breakpoint occupies 3 octets: The first two octets hold the
index of the subcarrier associated with the breakpoint. The
third octet holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz.
The subcarrier index is an unsigned number in the range 0 to
NSCus-1.
Xdsl2RaMode INTEGERdynamicRa(3) manual(1) raInit(2)
Specifies the rate adaptation behavior for the line.
The three possible behaviors are:
manual (1) - No Rate-Adaptation. The initialization
process attempts to synchronize to a
specified rate.
raInit (2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate
between minimum and maximum specified values.
dynamicRa (3)- Dynamic Rate-Adaptation during initialization
process as well as during Showtime.Xdsl2RfiBands OCTET STRING (SIZE (0..64))This type defines a subset of downstream PSD mask
breakpoints used to notch radio frequency interference (RFI)
bands.
Each RFI band is represented by 4 octets: a 16-bit start
subcarrier index followed by a 16-bit stop subcarrier
index.
There is a maximum of 16 RFI bands allowed.
The subcarrier index is an unsigned number in the range 0 to
NSC-1.
Xdsl2ScMaskDs OCTET STRING (SIZE (0..512))Each one of the 4096 bits in this OCTET STRING array
represents the corresponding subcarrier in the downstream
direction.
A bit value of one indicates that a subcarrier is masked.
Xdsl2ScMaskUs OCTET STRING (SIZE (0..512))Each one of the 4096 bits in this OCTET STRING array
represents the corresponding subcarrier in the upstream
direction. A bit value of one indicates that a subcarrier
is masked.
Xdsl2SymbolProtection INTEGEReightSymbols(10) elevenSymbols(13) fifteenSymbols(17) fiveSymbols(7) fourSymbols(6) fourteenSymbols(16) halfSymbol(2) nineSymbols(11) noProtection(1) sevenSymbols(9) singleSymbol(3) sixSymbols(8) sixteenSymbols(18) tenSymbols(12) thirteeSymbols(15) threeSymbols(5) twelveSymbols(14) twoSymbols(4)
This type specifies the minimum impulse noise protection
for the bearer channel if it is transported over DMT symbols
with a subcarrier spacing of 4.3125 kHz.
The possible values are:
'noProtection' (i.e., INP not required), 'halfSymbol' (i.e., INP
length is 1/2 symbol), and 1-16 symbols in steps of 1
symbol.
Xdsl2SymbolProtection8 INTEGEReightSymbols(9) elevenSymbols(12) fifteenSymbols(16) fiveSymbols(6) fourSymbols(5) fourteenSymbols(15) nineSymbols(10) noProtection(1) sevenSymbols(8) singleSymbol(2) sixSymbols(7) sixteenSymbols(17) tenSymbols(11) thirteeSymbols(14) threeSymbols(4) twelveSymbols(13) twoSymbols(3)
This type specifies the minimum impulse noise protection
for the bearer channel if it is transported over DMT symbols
with a subcarrier spacing of 8.625 kHz.
The possible values are:
'noProtection' (i.e., INP not required) and 1-16 symbols in
steps of 1 symbol.
Xdsl2TransmissionModeType Bitsansit1413(0) etsi(1) g9921IsdnNonOverlapped(4) g9921PotsNonOverlapped(2) g9921PotsOverlapped(3) g9921isdnOverlapped(5) g9921tcmIsdnNonOverlapped(6) g9921tcmIsdnOverlapped(7) g9921tcmIsdnSymmetric(12) g9922potsNonOverlapped(8) g9922potsOverlapped(9) g9922tcmIsdnNonOverlapped(10) g9922tcmIsdnOverlapped(11) g9923AnnexIAllDigNonOverlapped(28) g9923AnnexIAllDigOverlapped(29) g9923AnnexJAllDigNonOverlapped(30) g9923AnnexJAllDigOverlapped(31) g9923AnnexLMode1NonOverlapped(34) g9923AnnexLMode2NonOverlapped(35) g9923AnnexLMode3Overlapped(36) g9923AnnexLMode4Overlapped(37) g9923AnnexMPotsNonOverlapped(38) g9923AnnexMPotsOverlapped(39) g9923IsdnNonOverlapped(20) g9923PotsNonOverlapped(18) g9923PotsOverlapped(19) g9923isdnOverlapped(21) g9924AnnexIAllDigNonOverlapped(32) g9924AnnexIAllDigOverlapped(33) g9924potsNonOverlapped(24) g9924potsOverlapped(25) g9925AnnexIAllDigNonOverlapped(46) g9925AnnexIAllDigOverlapped(47) g9925AnnexJAllDigNonOverlapped(48) g9925AnnexJAllDigOverlapped(49) g9925AnnexMPotsNonOverlapped(50) g9925AnnexMPotsOverlapped(51) g9925IsdnNonOverlapped(42) g9925PotsNonOverlapped(40) g9925PotsOverlapped(41) g9925isdnOverlapped(43) g9932AnnexA(56) g9932AnnexB(57) g9932AnnexC(58) reserved1(13) reserved10(44) reserved11(45) reserved12(52) reserved13(53) reserved14(54) reserved15(55) reserved16(59) reserved17(60) reserved18(61) reserved19(62) reserved2(14) reserved20(63) reserved3(15) reserved4(16) reserved5(17) reserved6(22) reserved7(23) reserved8(26) reserved9(27)
A set of xDSL line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate and
Lite/splitterless, respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1,
wide U/S (F)
Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2,
narrow U/S(F)
Bit 36 : G.992.3 Annex L POTS overlapped, mode 3,
wide U/S (F)
Bit 37 : G.992.3 Annex L POTS overlapped, mode 4,
narrow U/S (F)
Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
Bit 39 : G.992.3 Annex M POTS overlapped (F)
Bit 40 : G.992.5 POTS non-overlapped (F)
Bit 41 : G.992.5 POTS overlapped (F)
Bit 42 : G.992.5 ISDN non-overlapped (F)
Bit 43 : G.992.5 ISDN overlapped (F)
Bit 44-45: Reserved
Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
Bit 51 : G.992.5 Annex M POTS overlapped (F)
Bit 52-55: Reserved
Bit 56 : G.993.2 Annex A
Bit 57 : G.993.2 Annex B
Bit 58 : G.993.2 Annex C
Bit 59-63: ReservedXdsl2Tssi OCTET STRING (SIZE (0..96))This is a structure that represents up to 32 transmit
spectrum shaping (TSSi) breakpoints.
Each breakpoint is a pair of values occupying 3 octets with the
following structure:
First 2 octets - Index of the subcarrier used in the context of
the breakpoint.
Third octet - The shaping parameter at the breakpoint.
The shaping parameter value is in the range 0 to 126 (units of
-0.5 dB). The special value 127 indicates that the subcarrier is
not transmitted.
The subcarrier index is an unsigned number in the range 0 to
NSC-1.Xdsl2Unit INTEGERxtuc(1) xtur(2)
Identifies a transceiver as being either xTU-C or xTU-R.
A VDSL2/ADSL/ADSL2 or ADSL2+ line consists of two
transceivers: an xTU-C and an xTU-R.
In the case of ADSL/ADSL2 and ADSL2+, those two transceivers are
also called atuc and atur.
In the case of VDSL2, those two transceivers are also called
vtuc and vtur.
Specified as an INTEGER, the two values are:
xtuc(1) -- central office transceiver
xtur(2) -- remote site transceiver
Xdsl2UpboKLF INTEGERauto(1) disableUpbo(3) override(2)
Defines the upstream power backoff force mode (UPBOKLF).
The three possible mode values are:
auto(1) - The VDSL Transceiver Unit (VTUs) will
autonomously determine the
electrical length.
override(2) - Forces the VTU-R to use the electrical
length, kl0, of the CO-MIB (UPBOKL) to
compute the UPBO.
disableUpbo(3) - Disables UPBO such that UPBO is not
utilized.