VDSL-LINE-MIB
Standards (IETF)The MIB module defining objects for the management of a pair
of VDSL transceivers at each end of the VDSL line. Each such
line has an entry in an ifTable which may include multiple
transceiver lines. An agent may reside at either end of the
VDSL line. However, the MIB is designed to require no
management communication between them beyond that inherent in
the low-level VDSL line protocol. The agent may monitor and
control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc -- (VTUC) transceiver at near (Central) end of line
Vtur -- (VTUR) transceiver at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
SES -- Severely Errored Second
UAS -- Unavailable Second
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs -- Sum of Seconds in which xxx has occured
(e.g., xxx = Lof, Los, Lpr, Lol)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks -- Blocks
Copyright (C) The Internet Society (2004). This version
of this MIB module is part of RFC 3728: see the RFC
itself for full legal notices.snmptranslate -m VDSL-LINE-MIB -Tpsnmpwalk -v2c -c <community> -m VDSL-LINE-MIB <host> 1.3.6.1.2.1.10.97Imports
| HC-PerfHist-TC-MIB | HCPerfCurrentCount, HCPerfIntervalCount, HCPerfIntervalThreshold, HCPerfInvalidIntervals, HCPerfTimeElapsed, HCPerfValidIntervals |
|---|---|
| HCNUM-TC | ZeroBasedCounter64 |
| IF-MIB | ifIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, transmission |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IvdslMIB | 1.3.6.1.2.1.10.97 | |||
identity The MIB module defining objects for the management of a pair
of VDSL transceivers at each end of the VDSL line. Each such
line has an entry in an ifTable which may include multiple
transceiver lines. An agent may reside at either end of the
VDSL line. However, the MIB is designed to require no
management communication between them beyond that inherent in
the low-level VDSL line protocol. The agent may monitor and
control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc -- (VTUC) transceiver at near (Central) end of line
Vtur -- (VTUR) transceiver at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
SES -- Severely Errored Second
UAS -- Unavailable Second
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs -- Sum of Seconds in which xxx has occured
(e.g., xxx = Lof, Los, Lpr, Lol)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks -- Blocks
Copyright (C) The Internet Society (2004). This version
of this MIB module is part of RFC 3728: see the RFC
itself for full legal notices. | ||||
| NvdslLineMib | 1.3.6.1.2.1.10.97.1 | |||
| NvdslNotifications | 1.3.6.1.2.1.10.97.1.0 | |||
| !vdslPerfLofsThreshNotification | 1.3.6.1.2.1.10.97.1.0.1 | |||
notification · current Loss of Framing 15-minute interval threshold (vdslLineAlarmConfThresh15MinLofs) reached.
| ||||
| !vdslPerfLossThreshNotification | 1.3.6.1.2.1.10.97.1.0.2 | |||
notification · current Loss of Signal 15-minute interval threshold (vdslLineAlarmConfThresh15MinLoss) reached.
| ||||
| !vdslPerfLprsThreshNotification | 1.3.6.1.2.1.10.97.1.0.3 | |||
notification · current Loss of Power 15-minute interval threshold (vdslLineAlarmConfThresh15MinLprs) reached.
| ||||
| !vdslPerfLolsThreshNotification | 1.3.6.1.2.1.10.97.1.0.4 | |||
notification · current Loss of Link 15-minute interval threshold (vdslLineAlarmConfThresh15MinLols) reached.
| ||||
| !vdslPerfESsThreshNotification | 1.3.6.1.2.1.10.97.1.0.5 | |||
notification · current Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinESs) reached.
| ||||
| !vdslPerfSESsThreshNotification | 1.3.6.1.2.1.10.97.1.0.6 | |||
notification · current Severely Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinSESs) reached.
| ||||
| !vdslPerfUASsThreshNotification | 1.3.6.1.2.1.10.97.1.0.7 | |||
notification · current Unavailable Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinUASs) reached.
| ||||
| !vdslDownMaxSnrMgnNotification | 1.3.6.1.2.1.10.97.1.0.8 | |||
notification · current The downstream Signal to Noise Margin exceeded vdslLineConfDownMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R.
| ||||
| !vdslDownMinSnrMgnNotification | 1.3.6.1.2.1.10.97.1.0.9 | |||
notification · current The downstream Signal to Noise Margin fell below vdslLineConfDownMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R.
| ||||
| !vdslUpMaxSnrMgnNotification | 1.3.6.1.2.1.10.97.1.0.10 | |||
notification · current The upstream Signal to Noise Margin exceeded vdslLineConfUpMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C.
| ||||
| !vdslUpMinSnrMgnNotification | 1.3.6.1.2.1.10.97.1.0.11 | |||
notification · current The upstream Signal to Noise Margin fell below vdslLineConfUpMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C.
| ||||
| !vdslInitFailureNotification | 1.3.6.1.2.1.10.97.1.0.12 | |||
notification · current Vtu initialization failed. See vdslPhysCurrStatus for potential reasons.
| ||||
| NvdslMibObjects | 1.3.6.1.2.1.10.97.1.1 | |||
| TvdslLineTable | 1.3.6.1.2.1.10.97.1.1.1 | NA | ||
table · not-accessible · current This table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | ||||
| RvdslLineEntry | 1.3.6.1.2.1.10.97.1.1.1.1 | NA | ||
| CvdslLineCoding | 1.3.6.1.2.1.10.97.1.1.1.1.1 | VdslLineCodingType | RO | |
column · VdslLineCodingType · read-only · current Specifies the VDSL coding type used on this line. | ||||
| CvdslLineType | 1.3.6.1.2.1.10.97.1.1.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Defines the type of VDSL physical line entity that exists,
by defining whether and how the line is channelized. If
the line is channelized, the value will be other than
noChannel(1). This object defines which channel type(s)
are supported. Defined values are:
noChannel(1) -- no channels exist
fastOnly(2) -- only fast channel exists
interleavedOnly(3) -- only interleaved channel exists
fastOrInterleaved(4) -- either fast or interleaved channel
-- exist, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
Note that 'slow' and 'interleaved' refer to the same
channel. In the case that the line is channelized, the
manager can use the ifStackTable to determine the ifIndex
for the associated channel(s).
| ||||
| CvdslLineConfProfile | 1.3.6.1.2.1.10.97.1.1.1.1.3 | SnmpAdminString (SIZE (1..32)) | RW | |
column · SnmpAdminString (SIZE (1..32)) · read-write · current The value of this object identifies the row in the VDSL Line Configuration Profile Table, vdslLineConfProfileTable, which applies for this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner. | ||||
| CvdslLineAlarmConfProfile | 1.3.6.1.2.1.10.97.1.1.1.1.4 | SnmpAdminString (SIZE (1..32)) | RW | |
column · SnmpAdminString (SIZE (1..32)) · read-write · current The value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, vdslLineAlarmConfProfileTable, which applies to this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner. | ||||
| TvdslPhysTable | 1.3.6.1.2.1.10.97.1.1.2 | NA | ||
table · not-accessible · current This table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | ||||
| RvdslPhysEntry | 1.3.6.1.2.1.10.97.1.1.2.1 | NA | ||
| CvdslPhysSide | 1.3.6.1.2.1.10.97.1.1.2.1.1 | VdslLineEntity | NA | |
column · VdslLineEntity · not-accessible · current Identifies whether the transceiver is the Vtuc or Vtur. | ||||
| CvdslPhysInvSerialNumber | 1.3.6.1.2.1.10.97.1.1.2.1.2 | SnmpAdminString (SIZE (0..32)) | RO | |
column · SnmpAdminString (SIZE (0..32)) · read-only · current The vendor specific string that identifies the vendor equipment. | ||||
| CvdslPhysInvVendorID | 1.3.6.1.2.1.10.97.1.1.2.1.3 | SnmpAdminString (SIZE (0..16)) | RO | |
column · SnmpAdminString (SIZE (0..16)) · read-only · current The vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation. | ||||
| CvdslPhysInvVersionNumber | 1.3.6.1.2.1.10.97.1.1.2.1.4 | SnmpAdminString (SIZE (0..16)) | RO | |
column · SnmpAdminString (SIZE (0..16)) · read-only · current The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readable characters in hexadecimal notation. | ||||
| CvdslPhysCurrSnrMgn | 1.3.6.1.2.1.10.97.1.1.2.1.5 | Integer32 (-127..127) | RO | |
column · Integer32 (-127..127) · read-only · current Noise Margin as seen by this Vtu with respect to its received signal in 0.25dB. The effective range is -31.75 to +31.75 dB.
| ||||
| CvdslPhysCurrAtn | 1.3.6.1.2.1.10.97.1.1.2.1.6 | Gauge32 (0..255) | RO | |
column · Gauge32 (0..255) · read-only · current Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB.
| ||||
| CvdslPhysCurrStatus | 1.3.6.1.2.1.10.97.1.1.2.1.7 | Bits | RO | |
column · Bits · read-only · current Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There are no defects on the line.
1 lossOfFraming Vtu failure due to not receiving
a valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to
link with peer Vtu. Set whenever
the transceiver is in the 'Warm
Start' state.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to
support requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus.
| ||||
| CvdslPhysCurrOutputPwr | 1.3.6.1.2.1.10.97.1.1.2.1.8 | Integer32 (0..160) | RO | |
column · Integer32 (0..160) · read-only · current Measured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence.
| ||||
| CvdslPhysCurrAttainableRate | 1.3.6.1.2.1.10.97.1.1.2.1.9 | Gauge32 | RO | |
column · Gauge32 · read-only · current Indicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate. Note that for SCM, the minimum and maximum data rates are equal. Note: 1 kbps = 1000 bps.
| ||||
| CvdslPhysCurrLineRate | 1.3.6.1.2.1.10.97.1.1.2.1.10 | Gauge32 | RO | |
column · Gauge32 · read-only · current Indicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 1000 bps.
| ||||
| TvdslChanTable | 1.3.6.1.2.1.10.97.1.1.3 | NA | ||
table · not-accessible · current This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125). | ||||
| RvdslChanEntry | 1.3.6.1.2.1.10.97.1.1.3.1 | NA | ||
| CvdslChanInterleaveDelay | 1.3.6.1.2.1.10.97.1.1.3.1.1 | Gauge32 | RO | |
column · Gauge32 · read-only · current Interleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), return a value of zero.
| ||||
| CvdslChanCrcBlockLength | 1.3.6.1.2.1.10.97.1.1.3.1.2 | Gauge32 | RO | |
column · Gauge32 · read-only · current Indicates the length of the channel data-block on which the CRC operates.
| ||||
| CvdslChanCurrTxRate | 1.3.6.1.2.1.10.97.1.1.3.1.3 | Gauge32 | RO | |
column · Gauge32 · read-only · current Actual transmit data rate on this channel. Note: 1 kbps = 1000 bps.
| ||||
| CvdslChanCurrTxSlowBurstProtect | 1.3.6.1.2.1.10.97.1.1.3.1.4 | Gauge32 (0..1275) | RO | |
column · Gauge32 (0..1275) · read-only · current Actual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a value of zero shall be returned.
| ||||
| CvdslChanCurrTxFastFec | 1.3.6.1.2.1.10.97.1.1.3.1.5 | Gauge32 (0..50) | RO | |
column · Gauge32 (0..50) · read-only · current Actual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For interleaved channels, a value of zero shall be returned.
| ||||
| TvdslPerfDataTable | 1.3.6.1.2.1.10.97.1.1.4 | NA | ||
table · not-accessible · current This table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | ||||
| RvdslPerfDataEntry | 1.3.6.1.2.1.10.97.1.1.4.1 | NA | ||
| CvdslPerfDataValidIntervals | 1.3.6.1.2.1.10.97.1.1.4.1.1 | HCPerfValidIntervals | RO | |
column · HCPerfValidIntervals · read-only · current Valid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslPerfDataInvalidIntervals | 1.3.6.1.2.1.10.97.1.1.4.1.2 | HCPerfInvalidIntervals | RO | |
column · HCPerfInvalidIntervals · read-only · current Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslPerfDataLofs | 1.3.6.1.2.1.10.97.1.1.4.1.3 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of seconds since the unit was last reset that there was Loss of Framing.
| ||||
| CvdslPerfDataLoss | 1.3.6.1.2.1.10.97.1.1.4.1.4 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of seconds since the unit was last reset that there was Loss of Signal.
| ||||
| CvdslPerfDataLprs | 1.3.6.1.2.1.10.97.1.1.4.1.5 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of seconds since the unit was last reset that there was Loss of Power.
| ||||
| CvdslPerfDataLols | 1.3.6.1.2.1.10.97.1.1.4.1.6 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of seconds since the unit was last reset that there was Loss of Link.
| ||||
| CvdslPerfDataESs | 1.3.6.1.2.1.10.97.1.1.4.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.
| ||||
| CvdslPerfDataSESs | 1.3.6.1.2.1.10.97.1.1.4.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Severely Errored Seconds since the unit was last reset.
| ||||
| CvdslPerfDataUASs | 1.3.6.1.2.1.10.97.1.1.4.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Unavailable Seconds since the unit was last reset.
| ||||
| CvdslPerfDataInits | 1.3.6.1.2.1.10.97.1.1.4.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts.
| ||||
| CvdslPerfDataCurr15MinTimeElapsed | 1.3.6.1.2.1.10.97.1.1.4.1.11 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current Total elapsed seconds in this interval.
| ||||
| CvdslPerfDataCurr15MinLofs | 1.3.6.1.2.1.10.97.1.1.4.1.12 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of seconds during this interval that there was Loss of Framing.
| ||||
| CvdslPerfDataCurr15MinLoss | 1.3.6.1.2.1.10.97.1.1.4.1.13 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of seconds during this interval that there was Loss of Signal.
| ||||
| CvdslPerfDataCurr15MinLprs | 1.3.6.1.2.1.10.97.1.1.4.1.14 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of seconds during this interval that there was Loss of Power.
| ||||
| CvdslPerfDataCurr15MinLols | 1.3.6.1.2.1.10.97.1.1.4.1.15 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of seconds during this interval that there was Loss of Link.
| ||||
| CvdslPerfDataCurr15MinESs | 1.3.6.1.2.1.10.97.1.1.4.1.16 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.
| ||||
| CvdslPerfDataCurr15MinSESs | 1.3.6.1.2.1.10.97.1.1.4.1.17 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of Severely Errored Seconds during this interval.
| ||||
| CvdslPerfDataCurr15MinUASs | 1.3.6.1.2.1.10.97.1.1.4.1.18 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of Unavailable Seconds during this interval.
| ||||
| CvdslPerfDataCurr15MinInits | 1.3.6.1.2.1.10.97.1.1.4.1.19 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of the line initialization attempts during this interval. This count includes both successful and failed attempts.
| ||||
| CvdslPerfData1DayValidIntervals | 1.3.6.1.2.1.10.97.1.1.4.1.20 | HCPerfValidIntervals | RO | |
column · HCPerfValidIntervals · read-only · current Valid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslPerfData1DayInvalidIntervals | 1.3.6.1.2.1.10.97.1.1.4.1.21 | HCPerfInvalidIntervals | RO | |
column · HCPerfInvalidIntervals · read-only · current Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslPerfDataCurr1DayTimeElapsed | 1.3.6.1.2.1.10.97.1.1.4.1.22 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current Number of seconds that have elapsed since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayLofs | 1.3.6.1.2.1.10.97.1.1.4.1.23 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayLoss | 1.3.6.1.2.1.10.97.1.1.4.1.24 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayLprs | 1.3.6.1.2.1.10.97.1.1.4.1.25 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayLols | 1.3.6.1.2.1.10.97.1.1.4.1.26 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayESs | 1.3.6.1.2.1.10.97.1.1.4.1.27 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Errored Seconds (ES) since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DaySESs | 1.3.6.1.2.1.10.97.1.1.4.1.28 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Severely Errored Seconds (SES) since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayUASs | 1.3.6.1.2.1.10.97.1.1.4.1.29 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Unavailable Seconds (UAS) since the beginning of the current 1-day interval.
| ||||
| CvdslPerfDataCurr1DayInits | 1.3.6.1.2.1.10.97.1.1.4.1.30 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts.
| ||||
| TvdslPerfIntervalTable | 1.3.6.1.2.1.10.97.1.1.5 | NA | ||
table · not-accessible · current This table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | ||||
| RvdslPerfIntervalEntry | 1.3.6.1.2.1.10.97.1.1.5.1 | NA | ||
row · not-accessible · current An entry in the vdslPerfIntervalTable. | ||||
| CvdslPerfIntervalNumber | 1.3.6.1.2.1.10.97.1.1.5.1.1 | Unsigned32 (1..96) | NA | |
column · Unsigned32 (1..96) · not-accessible · current Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional. | ||||
| CvdslPerfIntervalLofs | 1.3.6.1.2.1.10.97.1.1.5.1.2 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of seconds in the interval when there was Loss of Framing.
| ||||
| CvdslPerfIntervalLoss | 1.3.6.1.2.1.10.97.1.1.5.1.3 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of seconds in the interval when there was Loss of Signal.
| ||||
| CvdslPerfIntervalLprs | 1.3.6.1.2.1.10.97.1.1.5.1.4 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of seconds in the interval when there was Loss of Power.
| ||||
| CvdslPerfIntervalLols | 1.3.6.1.2.1.10.97.1.1.5.1.5 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of seconds in the interval when there was Loss of Link.
| ||||
| CvdslPerfIntervalESs | 1.3.6.1.2.1.10.97.1.1.5.1.6 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects.
| ||||
| CvdslPerfIntervalSESs | 1.3.6.1.2.1.10.97.1.1.5.1.7 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of Severely Errored Seconds in the interval.
| ||||
| CvdslPerfIntervalUASs | 1.3.6.1.2.1.10.97.1.1.5.1.8 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of Unavailable Seconds in the interval.
| ||||
| CvdslPerfIntervalInits | 1.3.6.1.2.1.10.97.1.1.5.1.9 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of the line initialization attempts during this interval. This count includes both successful and failed attempts. | ||||
| TvdslPerf1DayIntervalTable | 1.3.6.1.2.1.10.97.1.1.6 | NA | ||
table · not-accessible · current This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent. | ||||
| RvdslPerf1DayIntervalEntry | 1.3.6.1.2.1.10.97.1.1.6.1 | NA | ||
row · not-accessible · current An entry in the vdslPerf1DayIntervalTable. | ||||
| CvdslPerf1DayIntervalNumber | 1.3.6.1.2.1.10.97.1.1.6.1.1 | Unsigned32 (1..30) | NA | |
column · Unsigned32 (1..30) · not-accessible · current History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional. | ||||
| CvdslPerf1DayIntervalMoniSecs | 1.3.6.1.2.1.10.97.1.1.6.1.2 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
| ||||
| CvdslPerf1DayIntervalLofs | 1.3.6.1.2.1.10.97.1.1.6.1.3 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalLoss | 1.3.6.1.2.1.10.97.1.1.6.1.4 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalLprs | 1.3.6.1.2.1.10.97.1.1.6.1.5 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalLols | 1.3.6.1.2.1.10.97.1.1.6.1.6 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalESs | 1.3.6.1.2.1.10.97.1.1.6.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalSESs | 1.3.6.1.2.1.10.97.1.1.6.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalUASs | 1.3.6.1.2.1.10.97.1.1.6.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
| ||||
| CvdslPerf1DayIntervalInits | 1.3.6.1.2.1.10.97.1.1.6.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Count of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed attempts.
| ||||
| TvdslChanPerfDataTable | 1.3.6.1.2.1.10.97.1.1.7 | NA | ||
table · not-accessible · current This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125). | ||||
| RvdslChanPerfDataEntry | 1.3.6.1.2.1.10.97.1.1.7.1 | NA | ||
| CvdslChanValidIntervals | 1.3.6.1.2.1.10.97.1.1.7.1.1 | HCPerfValidIntervals | RO | |
column · HCPerfValidIntervals · read-only · current Valid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslChanInvalidIntervals | 1.3.6.1.2.1.10.97.1.1.7.1.2 | HCPerfInvalidIntervals | RO | |
column · HCPerfInvalidIntervals · read-only · current Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
| ||||
| CvdslChanFixedOctets | 1.3.6.1.2.1.10.97.1.1.7.1.3 | ZeroBasedCounter64 | RO | |
column · ZeroBasedCounter64 · read-only · current Count of corrected octets since the unit was last reset.
| ||||
| CvdslChanBadBlks | 1.3.6.1.2.1.10.97.1.1.7.1.4 | ZeroBasedCounter64 | RO | |
column · ZeroBasedCounter64 · read-only · current Count of uncorrectable blocks since the unit was last reset.
| ||||
| CvdslChanCurr15MinTimeElapsed | 1.3.6.1.2.1.10.97.1.1.7.1.5 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current Total elapsed seconds in this interval.
| ||||
| CvdslChanCurr15MinFixedOctets | 1.3.6.1.2.1.10.97.1.1.7.1.6 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of corrected octets in this interval.
| ||||
| CvdslChanCurr15MinBadBlks | 1.3.6.1.2.1.10.97.1.1.7.1.7 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of uncorrectable blocks in this interval.
| ||||
| CvdslChan1DayValidIntervals | 1.3.6.1.2.1.10.97.1.1.7.1.8 | HCPerfValidIntervals | RO | |
column · HCPerfValidIntervals · read-only · current Valid Intervals per definition found in HC-PerfHist-TC-MIB. | ||||
| CvdslChan1DayInvalidIntervals | 1.3.6.1.2.1.10.97.1.1.7.1.9 | HCPerfInvalidIntervals | RO | |
column · HCPerfInvalidIntervals · read-only · current Invalid Intervals per definition found in HC-PerfHist-TC-MIB. | ||||
| CvdslChanCurr1DayTimeElapsed | 1.3.6.1.2.1.10.97.1.1.7.1.10 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current Number of seconds that have elapsed since the beginning of the current 1-day interval.
| ||||
| CvdslChanCurr1DayFixedOctets | 1.3.6.1.2.1.10.97.1.1.7.1.11 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of corrected octets since the beginning of the current 1-day interval.
| ||||
| CvdslChanCurr1DayBadBlks | 1.3.6.1.2.1.10.97.1.1.7.1.12 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of uncorrectable blocks since the beginning of the current 1-day interval.
| ||||
| TvdslChanIntervalTable | 1.3.6.1.2.1.10.97.1.1.8 | NA | ||
table · not-accessible · current This table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125). | ||||
| RvdslChanIntervalEntry | 1.3.6.1.2.1.10.97.1.1.8.1 | NA | ||
row · not-accessible · current An entry in the vdslChanIntervalTable. | ||||
| CvdslChanIntervalNumber | 1.3.6.1.2.1.10.97.1.1.8.1.1 | Unsigned32 (1..96) | NA | |
column · Unsigned32 (1..96) · not-accessible · current Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional. | ||||
| CvdslChanIntervalFixedOctets | 1.3.6.1.2.1.10.97.1.1.8.1.2 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of corrected octets in this interval.
| ||||
| CvdslChanIntervalBadBlks | 1.3.6.1.2.1.10.97.1.1.8.1.3 | HCPerfIntervalCount | RO | |
column · HCPerfIntervalCount · read-only · current Count of uncorrectable blocks in this interval.
| ||||
| TvdslChan1DayIntervalTable | 1.3.6.1.2.1.10.97.1.1.9 | NA | ||
table · not-accessible · current This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent. | ||||
| RvdslChan1DayIntervalEntry | 1.3.6.1.2.1.10.97.1.1.9.1 | NA | ||
row · not-accessible · current An entry in the vdslChan1DayIntervalTable. | ||||
| CvdslChan1DayIntervalNumber | 1.3.6.1.2.1.10.97.1.1.9.1.1 | Unsigned32 (1..30) | NA | |
column · Unsigned32 (1..30) · not-accessible · current History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional. | ||||
| CvdslChan1DayIntervalMoniSecs | 1.3.6.1.2.1.10.97.1.1.9.1.2 | HCPerfTimeElapsed | RO | |
column · HCPerfTimeElapsed · read-only · current The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
| ||||
| CvdslChan1DayIntervalFixedOctets | 1.3.6.1.2.1.10.97.1.1.9.1.3 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of corrected octets in this interval.
| ||||
| CvdslChan1DayIntervalBadBlks | 1.3.6.1.2.1.10.97.1.1.9.1.4 | HCPerfCurrentCount | RO | |
column · HCPerfCurrentCount · read-only · current Count of uncorrectable blocks in this interval.
| ||||
| TvdslLineConfProfileTable | 1.3.6.1.2.1.10.97.1.1.11 | NA | ||
table · not-accessible · current This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. Entries in this table MUST be maintained in a persistent manner. | ||||
| RvdslLineConfProfileEntry | 1.3.6.1.2.1.10.97.1.1.11.1 | NA | ||
row · not-accessible · current Each entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | ||||
| CvdslLineConfProfileName | 1.3.6.1.2.1.10.97.1.1.11.1.1 | SnmpAdminString (SIZE (1..32)) | NA | |
column · SnmpAdminString (SIZE (1..32)) · not-accessible · current This object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | ||||
| CvdslLineConfDownRateMode | 1.3.6.1.2.1.10.97.1.1.11.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current Specifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality.
| ||||
| CvdslLineConfUpRateMode | 1.3.6.1.2.1.10.97.1.1.11.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current Specifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality.
| ||||
| CvdslLineConfDownMaxPwr | 1.3.6.1.2.1.10.97.1.1.11.1.4 | Unsigned32 (0..58) | RC | |
column · Unsigned32 (0..58) · read-create · current Specifies the maximum aggregate downstream power level in the range 0 to 14.5 dBm.
| ||||
| CvdslLineConfUpMaxPwr | 1.3.6.1.2.1.10.97.1.1.11.1.5 | Unsigned32 (0..58) | RC | |
column · Unsigned32 (0..58) · read-create · current Specifies the maximum aggregate upstream power level in the range 0 to 14.5 dBm.
| ||||
| CvdslLineConfDownMaxSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.6 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the maximum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
| ||||
| CvdslLineConfDownMinSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.7 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the minimum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
| ||||
| CvdslLineConfDownTargetSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.8 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the target downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.
| ||||
| CvdslLineConfUpMaxSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.9 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the maximum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
| ||||
| CvdslLineConfUpMinSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.10 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the minimum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
| ||||
| CvdslLineConfUpTargetSnrMgn | 1.3.6.1.2.1.10.97.1.1.11.1.11 | Unsigned32 (0..127) | RC | |
column · Unsigned32 (0..127) · read-create · current Specifies the target upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.
| ||||
| CvdslLineConfDownFastMaxDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.12 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the maximum downstream fast channel data rate in steps of 1000 bits/second.
| ||||
| CvdslLineConfDownFastMinDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.13 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the minimum downstream fast channel data rate in steps of 1000 bits/second.
| ||||
| CvdslLineConfDownSlowMaxDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.14 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derived from the sum of maximum downstream fast and slow channel data rates.
| ||||
| CvdslLineConfDownSlowMinDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.15 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derived from the sum of minimum downstream fast and slow channel data rates.
| ||||
| CvdslLineConfUpFastMaxDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.16 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived from the sum of maximum upstream fast and slow channel data rates.
| ||||
| CvdslLineConfUpFastMinDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.17 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived from the sum of minimum upstream fast and slow channel data rates.
| ||||
| CvdslLineConfUpSlowMaxDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.18 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the maximum upstream slow channel data rate in steps of 1000 bits/second.
| ||||
| CvdslLineConfUpSlowMinDataRate | 1.3.6.1.2.1.10.97.1.1.11.1.19 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the minimum upstream slow channel data rate in steps of 1000 bits/second.
| ||||
| CvdslLineConfDownRateRatio | 1.3.6.1.2.1.10.97.1.1.11.1.20 | Unsigned32 (0..100) | RC | |
column · Unsigned32 (0..100) · read-create · current For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents downstream Fast Channel Allocation / Slow Channel Allocation.
| ||||
| CvdslLineConfUpRateRatio | 1.3.6.1.2.1.10.97.1.1.11.1.21 | Unsigned32 (0..100) | RC | |
column · Unsigned32 (0..100) · read-create · current For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents upstream Fast Channel Allocation/Slow Channel Allocation.
| ||||
| CvdslLineConfDownMaxInterDelay | 1.3.6.1.2.1.10.97.1.1.11.1.22 | Unsigned32 (0..255) | RC | |
column · Unsigned32 (0..255) · read-create · current Specifies the maximum interleave delay for the downstream slow channel.
| ||||
| CvdslLineConfUpMaxInterDelay | 1.3.6.1.2.1.10.97.1.1.11.1.23 | Unsigned32 (0..255) | RC | |
column · Unsigned32 (0..255) · read-create · current Specifies the maximum interleave delay for the upstream slow channel.
| ||||
| CvdslLineConfDownPboControl | 1.3.6.1.2.1.10.97.1.1.11.1.24 | INTEGER | RC | |
column · INTEGER · read-create · current Downstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfDownPboLevel.
| ||||
| CvdslLineConfUpPboControl | 1.3.6.1.2.1.10.97.1.1.11.1.25 | INTEGER | RC | |
column · INTEGER · read-create · current Upstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfUpPboLevel.
| ||||
| CvdslLineConfDownPboLevel | 1.3.6.1.2.1.10.97.1.1.11.1.26 | Unsigned32 (0..160) | RC | |
column · Unsigned32 (0..160) · read-create · current Specifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3).
| ||||
| CvdslLineConfUpPboLevel | 1.3.6.1.2.1.10.97.1.1.11.1.27 | Unsigned32 (0..160) | RC | |
column · Unsigned32 (0..160) · read-create · current Specifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3).
| ||||
| CvdslLineConfDeploymentScenario | 1.3.6.1.2.1.10.97.1.1.11.1.28 | INTEGER | RC | |
column · INTEGER · read-create · current The VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central office. Changes to this value will have no effect on the transceiver.
| ||||
| CvdslLineConfAdslPresence | 1.3.6.1.2.1.10.97.1.1.11.1.29 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates presence of ADSL service in the associated
cable bundle/binder.
none(1) indicates no ADSL service in the bundle
adslOverPots(2) indicates ADSL service over POTS is
present in the bundle
adslOverISDN(3) indicates ADSL service over ISDN is
present in the bundle
| ||||
| CvdslLineConfApplicableStandard | 1.3.6.1.2.1.10.97.1.1.11.1.30 | INTEGER | RC | |
column · INTEGER · read-create · current The VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a standard other than the above.
| ||||
| CvdslLineConfBandPlan | 1.3.6.1.2.1.10.97.1.1.11.1.31 | INTEGER | RC | |
column · INTEGER · read-create · current The VDSL band plan to be used for the line.
bandPlan997(1) is to be used for
ITU-T G.993.1 Bandplan-B
ETSI Bandplan
ANSI Plan 997
bandPlan998(2) is to be used for
ITU-T G.993.1 Bandplan-A
ANSI Plan 998
bandPlanFx(3) is to be used for
ITU-T G.993.1 Bandplan-C.
other(4) is to be used for
non-standard bandplans.
If this object is set to bandPlanFx(3), then the
object vdslLineConfBandPlanFx MUST also be set.
| ||||
| CvdslLineConfBandPlanFx | 1.3.6.1.2.1.10.97.1.1.11.1.32 | Unsigned32 (3750..12000) | RC | |
column · Unsigned32 (3750..12000) · read-create · current The frequency limit between bands D2 and U2 when vdslLineConfBandPlan is set to bandPlanFx(3).
| ||||
| CvdslLineConfBandOptUsage | 1.3.6.1.2.1.10.97.1.1.11.1.33 | INTEGER | RC | |
column · INTEGER · read-create · current Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upstream downstream(3) indicates Opt usage is for downstream.
| ||||
| CvdslLineConfUpPsdTemplate | 1.3.6.1.2.1.10.97.1.1.11.1.34 | INTEGER | RC | |
column · INTEGER · read-create · current The upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).
| ||||
| CvdslLineConfDownPsdTemplate | 1.3.6.1.2.1.10.97.1.1.11.1.35 | INTEGER | RC | |
column · INTEGER · read-create · current The downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).
| ||||
| CvdslLineConfHamBandMask | 1.3.6.1.2.1.10.97.1.1.11.1.36 | Bits | RC | |
column · Bits · read-create · current The transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or more of these bands.
Amateur radio band notching is defined in the VDSL
spectrum as follows:
Band Start Frequency Stop Frequency
---- ------------------ --------------------------------
30m 1810 kHz 2000 kHz
40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI)
80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI)
160m 10100 kHz 10150 kHz
Notching for each standard band can be enabled or disabled
via the bit mask.
Two custom notches may be specified. If either of these
are enabled via the bit mask, then the following objects
MUST be specified:
If customNotch1 is enabled, then both
vdslLineConfCustomNotch1Start
vdslLineConfCustomNotch1Stop
MUST be specified.
If customNotch2 is enabled, then both
vdslLineConfCustomNotch2Start
vdslLineConfCustomNotch2Stop
MUST be specified.
| ||||
| CvdslLineConfCustomNotch1Start | 1.3.6.1.2.1.10.97.1.1.11.1.37 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNotch1Stop.
| ||||
| CvdslLineConfCustomNotch1Stop | 1.3.6.1.2.1.10.97.1.1.11.1.38 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNotch1Start.
| ||||
| CvdslLineConfCustomNotch2Start | 1.3.6.1.2.1.10.97.1.1.11.1.39 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNotch2Stop.
| ||||
| CvdslLineConfCustomNotch2Stop | 1.3.6.1.2.1.10.97.1.1.11.1.40 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNotch2Start.
| ||||
| CvdslLineConfDownTargetSlowBurst | 1.3.6.1.2.1.10.97.1.1.11.1.41 | Unsigned32 (0..1275) | RC | |
column · Unsigned32 (0..1275) · read-create · current Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
| ||||
| CvdslLineConfUpTargetSlowBurst | 1.3.6.1.2.1.10.97.1.1.11.1.42 | Unsigned32 (0..1275) | RC | |
column · Unsigned32 (0..1275) · read-create · current Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
| ||||
| CvdslLineConfDownMaxFastFec | 1.3.6.1.2.1.10.97.1.1.11.1.43 | Unsigned32 (0..50) | RC | |
column · Unsigned32 (0..50) · read-create · current This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
| ||||
| CvdslLineConfUpMaxFastFec | 1.3.6.1.2.1.10.97.1.1.11.1.44 | Unsigned32 (0..50) | RC | |
column · Unsigned32 (0..50) · read-create · current This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
| ||||
| CvdslLineConfLineType | 1.3.6.1.2.1.10.97.1.1.11.1.45 | INTEGER | RC | |
column · INTEGER · read-create · current This parameter provisions the VDSL physical entity at
start-up by defining whether and how the line will be
channelized, i.e., which channel type(s) are supported.
If the line is to be channelized, the value will be other
than noChannel(1).
This configuration can be activated only during start-up.
Afterwards, the value of vdslLineType coincides with the
value of vdslLineConfLineType. Depending on this value,
the corresponding entries in the ifTable for the
interleaved and the fast channels are enabled or disabled
according to the value of their ifOperStatus.
Defined values are:
noChannel(1) -- no channels exist
fastOnly(2) -- only fast channel exists
interleavedOnly(3) -- only interleaved channel exists
fastOrInterleaved(4) -- either fast or interleaved channel
-- exists, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
Note that 'slow' and 'interleaved' refer to the same
channel.
| ||||
| CvdslLineConfProfRowStatus | 1.3.6.1.2.1.10.97.1.1.11.1.46 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. Note that some changes may require that any referenced lines be restarted (e.g., vdslLineConfLineType). | ||||
| TvdslLineAlarmConfProfileTable | 1.3.6.1.2.1.10.97.1.1.20 | NA | ||
table · not-accessible · current This table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. Entries in this table MUST be maintained in a persistent manner. | ||||
| RvdslLineAlarmConfProfileEntry | 1.3.6.1.2.1.10.97.1.1.20.1 | NA | ||
row · not-accessible · current Each entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | ||||
| CvdslLineAlarmConfProfileName | 1.3.6.1.2.1.10.97.1.1.20.1.1 | SnmpAdminString (SIZE (1..32)) | NA | |
column · SnmpAdminString (SIZE (1..32)) · not-accessible · current The name for this profile as specified by an administrator. | ||||
| CvdslLineAlarmConfThresh15MinLofs | 1.3.6.1.2.1.10.97.1.1.20.1.2 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of loss of frame seconds (lofs) within any given 15-minute performance data collection interval. If the value of loss of frame seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfThresh15MinLoss | 1.3.6.1.2.1.10.97.1.1.20.1.3 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of loss of signal seconds (loss) within any given 15-minute performance data collection interval. If the value of loss of signal seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLossThreshNotification notification will be generated. One notification will be sent per interval per endpoint.
| ||||
| CvdslLineAlarmConfThresh15MinLprs | 1.3.6.1.2.1.10.97.1.1.20.1.4 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of loss of power seconds (lprs) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfThresh15MinLols | 1.3.6.1.2.1.10.97.1.1.20.1.5 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of loss of link seconds (lols) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfThresh15MinESs | 1.3.6.1.2.1.10.97.1.1.20.1.6 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfESsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfThresh15MinSESs | 1.3.6.1.2.1.10.97.1.1.20.1.7 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfSESsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfThresh15MinUASs | 1.3.6.1.2.1.10.97.1.1.20.1.8 | HCPerfIntervalThreshold | RC | |
column · HCPerfIntervalThreshold · read-create · current This object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value of unavailable seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfUASsThreshNotification notification will be generated. No more than one notification will be sent per interval.
| ||||
| CvdslLineAlarmConfInitFailure | 1.3.6.1.2.1.10.97.1.1.20.1.9 | TruthValue | RC | |
column · TruthValue · read-create · current This object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs. | ||||
| CvdslLineAlarmConfProfRowStatus | 1.3.6.1.2.1.10.97.1.1.20.1.10 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. | ||||
| NvdslConformance | 1.3.6.1.2.1.10.97.1.3 | |||
| NvdslGroups | 1.3.6.1.2.1.10.97.1.3.1 | |||
| GvdslGroup | 1.3.6.1.2.1.10.97.1.3.1.1 | |||
group · current A collection of objects providing information about a VDSL Line.
| ||||
| GvdslNotificationGroup | 1.3.6.1.2.1.10.97.1.3.1.2 | |||
group · current This group supports notifications of significant conditions associated with VDSL Lines.
| ||||
| NvdslCompliances | 1.3.6.1.2.1.10.97.1.3.2 | |||
| MvdslLineMibCompliance | 1.3.6.1.2.1.10.97.1.3.2.1 | |||
compliance · current The compliance statement for SNMP entities which manage VDSL interfaces.
| ||||
Textual conventions
VdslLineCodingTypeINTEGERmcm(2)other(1)scm(3)This data type is used as the syntax for the VDSL Line Code. Attributes with this syntax identify the line coding used. Specified as an INTEGER, the three values are: other(1) -- none of the following mcm(2) -- Multiple Carrier Modulation scm(3) -- Single Carrier Modulation
VdslLineEntityINTEGERvtuc(1)vtur(2)Identifies a transceiver as being either Vtuc or Vtur. A VDSL line consists of two transceivers, a Vtuc and a Vtur. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: vtuc(1) -- central site transceiver vtur(2) -- remote site transceiver
Traps / Notifications
- vdslDownMaxSnrMgnNotification
1.3.6.1.2.1.10.97.1.0.8 - vdslDownMinSnrMgnNotification
1.3.6.1.2.1.10.97.1.0.9 - vdslInitFailureNotification
1.3.6.1.2.1.10.97.1.0.12 - vdslPerfESsThreshNotification
1.3.6.1.2.1.10.97.1.0.5 - vdslPerfLofsThreshNotification
1.3.6.1.2.1.10.97.1.0.1 - vdslPerfLolsThreshNotification
1.3.6.1.2.1.10.97.1.0.4 - vdslPerfLossThreshNotification
1.3.6.1.2.1.10.97.1.0.2 - vdslPerfLprsThreshNotification
1.3.6.1.2.1.10.97.1.0.3 - vdslPerfSESsThreshNotification
1.3.6.1.2.1.10.97.1.0.6 - vdslPerfUASsThreshNotification
1.3.6.1.2.1.10.97.1.0.7 - vdslUpMaxSnrMgnNotification
1.3.6.1.2.1.10.97.1.0.10 - vdslUpMinSnrMgnNotification
1.3.6.1.2.1.10.97.1.0.11
Groups and compliance
Used by
- ISKRATEL-MSAN-MIB (kontron)
- ZYXEL-IES5000-MIB (zyxel)