LAN-EMULATION-CLIENT-MIB
ATM ForumThis module defines a portion of the management information base (MIB) for managing ATM LAN Emulation Client nodes. It is meant to be used in connection with the AToM MIB and MIB-II / RFC 1573 'ifTable' entries for each LEC / emulated 802.x network interface.
snmptranslate -m LAN-EMULATION-CLIENT-MIB -Tpsnmpwalk -v2c -c <community> -m LAN-EMULATION-CLIENT-MIB <host> 1.3.6.1.4.1.353.5.3.1Imports
| IF-MIB | ifIndex |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NatmfLanEmulation | 1.3.6.1.4.1.353.5.3 | |||
| IleClientMIB | 1.3.6.1.4.1.353.5.3.1 | |||
identity This module defines a portion of the management information base (MIB) for managing ATM LAN Emulation Client nodes. It is meant to be used in connection with the AToM MIB and MIB-II / RFC 1573 'ifTable' entries for each LEC / emulated 802.x network interface. | ||||
| NleClientMIBObjects | 1.3.6.1.4.1.353.5.3.1.1 | |||
| TlecConfigTable | 1.3.6.1.4.1.353.5.3.1.1.1 | NA | ||
table · not-accessible · current A table describing all of the LAN Emulation Clients
implemented by this host. Each LE Client has a row
in the MIB-II/RFC 1573 Interfaces table (describing
the emulated packet interface it presents to higher
layers). Each LE Client also has a row in this and
other LEC MIB tables (describing its interface with
other LAN Emulation components).
This table contains configuration variables. Three
extension tables contain client status, performance
statistics, and information about control/multicast
VCCs.
Unlike hardware ports, LE Clients can be created by
management. However, the RFC 1573 Interfaces table
does not directly support row creation. Therefore,
creating or deleting a row in the lecConfigTable is
defined to have the side effect of creating or
deleting corresponding rows in
- the MIB-II / RFC 1573 Interfaces table,
- the 'lecMappingTable',
- the 'lecStatusTable',
- the 'lecServerVccTable',
- the 'lecStatisticsTable', and
- any other dependent tables
New Interfaces table rows for LAN Emulation Clients
always have 'ifAdminStatus' set to 'down'.
A Note On Indexing:
-------------------
Most of the tables in this MIB are indexed in whole
or in part by 'lecIndex' - not by 'ifIndex'.
Why is there a separate index?
Traditionally, ifIndex values are chosen by agents,
and are permitted to change across restarts. Using
ifIndex to index lecConfigTable could complicate
row creation and/or cause interoperability problems
(if each agent had special restrictions on ifIndex).
Having a separate index avoids these problems. | ||||
| RlecConfigEntry | 1.3.6.1.4.1.353.5.3.1.1.1.1 | NA | ||
row · not-accessible · current Each table entry contains configuration information for one LAN Emulation Client. Most of the objects are derived from Initial State Parameters in the LAN Emulation specification.
| ||||
| ClecIndex | 1.3.6.1.4.1.353.5.3.1.1.1.1.1 | INTEGER (1..2147483647) | NA | |
column · INTEGER (1..2147483647) · not-accessible · current A value which uniquely identifies this conceptual row in the lecConfigTable. If the conceptual row identified by this value of lecIndex is recreated following an agent restart, the same value of lecIndex must be used to identify the recreated row. (However, the Interfaces table index associated with the client may change.) | ||||
| ClecRowStatus | 1.3.6.1.4.1.353.5.3.1.1.1.1.2 | RowStatus | RC | |
column · RowStatus · read-create · current This object lets network managers create and delete
LAN Emulation Clients, on systems that support this
optional capability.
It does not control Joins and Terminations; they are
controlled by 'ifAdminStatus'. However, taking rows
out of service will have the side effect of changing
their 'ifAdminStatus' values to 'down', thus causing
any active emulated LAN connections to be terminated.
Within each conceptual lecConfigTable row, objects
which are writable may be modified regardless of the
value of lecRowStatus. It is not necessary to set a
row's status to 'notInService' first.
When creating a LAN Emulation Client, it is up to the
management station to determine a suitable 'lecIndex'.
To facilitate interoperability, agents should not put
any restrictions on the 'lecIndex' beyond the obvious
ones that it be valid and unused.
If you create a LAN Emulation Client via this object,
it will initially have
'ifAdminStatus' = 'down'
'ifOperStatus' = 'down'
'lecInterfaceState' = 'initialState' | ||||
| ClecOwner | 1.3.6.1.4.1.353.5.3.1.1.1.1.3 | OwnerString (SIZE (0..127)) | RC | |
column · OwnerString (SIZE (0..127)) · read-create · current The entity that configured this entry and is therefore using the resources assigned to it. | ||||
| ClecConfigMode | 1.3.6.1.4.1.353.5.3.1.1.1.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates whether this LAN Emulation Client should
auto-configure the next time it is (re)started.
In automatic(1) mode, a client uses a LAN Emulation
Configuration Server to learn the ATM address of its
LAN Emulation Server, and to obtain other parameters.
lecConfig{ LanType, MaxDataFrameSize, LanName } are
used in the Configure request. lecConfigLesAtmAddress
is ignored.
In manual(2) mode, management tells the client the
ATM address of its LAN Emulation Server and the
values of other parameters.
lecConfig{ LanType, MaxDataFrameSize, LanName } are
used in the Join request. lecConfigLesAtmAddress
tells the client which LES to call.
| ||||
| ClecConfigLanType | 1.3.6.1.4.1.353.5.3.1.1.1.1.5 | LecDataFrameFormat | RC | |
column · LecDataFrameFormat · read-create · current C2 LAN Type.
The data frame format which this client will use the
next time it returns to the Initial State.
Auto-configuring clients use this parameter in their
Configure requests. Manually-configured clients use
it in their Join requests.
This MIB object will not be overwritten with the new
value from a LE_{JOIN,CONFIGURE}_RESPONSE. Instead,
lecActualLanType will be. | ||||
| ClecConfigMaxDataFrameSize | 1.3.6.1.4.1.353.5.3.1.1.1.1.6 | LecDataFrameSize | RC | |
column · LecDataFrameSize · read-create · current C3 Maximum Data Frame Size.
The maximum data frame size which this client will
use the next time it returns to the Initial State.
Auto-configuring clients use this parameter in their
Configure requests. Manually-configured clients use
it in their Join requests.
This MIB object will not be overwritten with the new
value from a LE_{JOIN,CONFIGURE}_RESPONSE. Instead,
lecActualMaxDataFrameSize will be. | ||||
| ClecConfigLanName | 1.3.6.1.4.1.353.5.3.1.1.1.1.7 | OCTET STRING (SIZE (0..32)) | RC | |
column · OCTET STRING (SIZE (0..32)) · read-create · current C5 ELAN Name.
The ELAN Name this client will use the next time it
returns to the Initial State.
Auto-configuring clients use this parameter in their
Configure requests. Manually-configured clients use
it in their Join requests.
This MIB object will not be overwritten with the new
value from a LE_{JOIN,CONFIGURE}_RESPONSE. Instead,
lecActualLanName will be. | ||||
| ClecConfigLesAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.1.1.8 | AtmLaneAddress | RC | |
column · AtmLaneAddress · read-create · current C9 LE Server ATM Address. The LAN Emulation Server which this client will use the next time it is started in manual configuration mode. When lecConfigMode is 'automatic', there is no need to set this address, and no advantage to doing so. The client will use the LECS to find a LES, putting the auto-configured address in lecActualLesAtmAddress while leaving lecConfigLesAtmAddress alone. | ||||
| ClecControlTimeout | 1.3.6.1.4.1.353.5.3.1.1.1.1.9 | INTEGER (10..300) | RC | |
column · INTEGER (10..300) · read-create · current C7 Control Time-out. Time out period used for
timing out most request/response control frame
interactions, as specified elsewhere [in the
LAN Emulation specification].
This time value is expressed in seconds.
| ||||
| ClecMaxUnknownFrameCount | 1.3.6.1.4.1.353.5.3.1.1.1.1.10 | INTEGER (1..10) | RC | |
column · INTEGER (1..10) · read-create · current C10 Maximum Unknown Frame Count. See the description of lecMaxUnknownFrameTime below.
| ||||
| ClecMaxUnknownFrameTime | 1.3.6.1.4.1.353.5.3.1.1.1.1.11 | INTEGER (1..60) | RC | |
column · INTEGER (1..60) · read-create · current C11 Maximum Unknown Frame Time. Within the period of
time defined by the Maximum Unknown Frame Time, a
LE Client will send no more than Maximum Unknown
Frame Count frames to the BUS for a given unicast
LAN Destination, and it must also initiate the
address resolution protocol to resolve that LAN
Destination.
This time value is expressed in seconds.
| ||||
| ClecVccTimeoutPeriod | 1.3.6.1.4.1.353.5.3.1.1.1.1.12 | Integer32 | RC | |
column · Integer32 · read-create · current C12 VCC Time-out Period. A LE Client SHOULD release
any Data Direct VCC that it has not used to
transmit or receive any data frames for the
length of the VCC Time-out Period. This parameter
is only meaningful for SVC Data Direct VCCs.
This time value is expressed in seconds. The default
value is 20 minutes. A value of 0 seconds means that
the timeout period is infinite. Negative values will
be rejected by the agent.
| ||||
| ClecMaxRetryCount | 1.3.6.1.4.1.353.5.3.1.1.1.1.13 | INTEGER (0..2) | RC | |
column · INTEGER (0..2) · read-create · current C13 Maximum Retry Count. A LE CLient MUST not retry a LE_ARP_REQUEST for a given frame's LAN destination more than Maximum Retry Count times, after the first LE_ARP_REQUEST for that same frame's LAN destination. | ||||
| ClecAgingTime | 1.3.6.1.4.1.353.5.3.1.1.1.1.14 | INTEGER (10..300) | RC | |
column · INTEGER (10..300) · read-create · current C17 Aging Time. The maximum time that a LE Client
will maintain an entry in its LE_ARP cache in
the absence of a verification of that
relationship.
This time value is expressed in seconds.
| ||||
| ClecForwardDelayTime | 1.3.6.1.4.1.353.5.3.1.1.1.1.15 | INTEGER (4..30) | RC | |
column · INTEGER (4..30) · read-create · current C18 Forward Delay Time. The maximum time that a LE
Client will maintain an entry for a non-local MAC
address in its LE_ARP cache in the absence of a
verification of that relationship, as long as the
Topology Change flag C19 is true.
lecForwardDelayTime SHOULD BE less than lecAgingTime.
When it is not, lecAgingTime governs LE_ARP aging.
This time value is expressed in seconds.
| ||||
| ClecExpectedArpResponseTime | 1.3.6.1.4.1.353.5.3.1.1.1.1.16 | INTEGER (1..30) | RC | |
column · INTEGER (1..30) · read-create · current C20 Expected LE_ARP Response Time. The maximum time
that the LEC expects an LE_ARP_REQUEST/
LE_ARP_RESPONSE cycle to take. Used for retries
and verifies.
This time value is expressed in seconds.
| ||||
| ClecFlushTimeOut | 1.3.6.1.4.1.353.5.3.1.1.1.1.17 | INTEGER (1..4) | RC | |
column · INTEGER (1..4) · read-create · current C21 Flush Time-out. Time limit to wait to receive a
LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has
been sent before taking recovery action.
This time value is expressed in seconds.
| ||||
| ClecPathSwitchingDelay | 1.3.6.1.4.1.353.5.3.1.1.1.1.18 | INTEGER (1..8) | RC | |
column · INTEGER (1..8) · read-create · current C22 Path Switching Delay. The time since sending a
frame to the BUS after which the LE Client may
assume that the frame has been either discarded
or delivered to the recipient. May be used to
bypass the Flush protocol.
This time value is expressed in seconds.
| ||||
| ClecLocalSegmentID | 1.3.6.1.4.1.353.5.3.1.1.1.1.19 | INTEGER (0..4095) | RC | |
column · INTEGER (0..4095) · read-create · current C23 Local Segment ID. The segment ID of the emulated LAN. This is only required for IEEE 802.5 clients that are Source Routing bridges. | ||||
| ClecMulticastSendType | 1.3.6.1.4.1.353.5.3.1.1.1.1.20 | INTEGER | RC | |
column · INTEGER · read-create · current C24 Multicast Send VCC Type. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. This is the method to be used by the LE Client when specifying traffic parameters when it sets up the Multicast Send VCC for this emulated LAN.
| ||||
| ClecMulticastSendAvgRate | 1.3.6.1.4.1.353.5.3.1.1.1.1.21 | Integer32 | RC | |
column · Integer32 · read-create · current C25 Multicast Send VCC AvgRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Sustained Cell Rate to be requested by LE Client when setting up Multicast Send VCC, if using Variable bit rate codings.
| ||||
| ClecMulticastSendPeakRate | 1.3.6.1.4.1.353.5.3.1.1.1.1.22 | Integer32 | RC | |
column · Integer32 · read-create · current C26 Multicast Send VCC PeakRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Peak Cell Rate to be requested by LE Client when setting up the Multicast Send VCC when using either Variable or Constant bit rate codings.
| ||||
| ClecConnectionCompleteTimer | 1.3.6.1.4.1.353.5.3.1.1.1.1.23 | INTEGER (1..10) | RC | |
column · INTEGER (1..10) · read-create · current C28 Connection Complete Timer. Optional. In
Connection Establishment this is the time period
in which data or a READY_IND message is expected
from a Calling Party.
This time value is expressed in seconds.
| ||||
| TlecStatusTable | 1.3.6.1.4.1.353.5.3.1.1.2 | NA | ||
table · not-accessible · current A read-only table containing identification, status, and operational information about the LAN Emulation Clients this agent manages. | ||||
| RlecStatusEntry | 1.3.6.1.4.1.353.5.3.1.1.2.1 | NA | ||
row · not-accessible · current Each table entry contains information about one LAN Emulation Client.
| ||||
| ClecIfIndex | 1.3.6.1.4.1.353.5.3.1.1.2.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current This object identifies the logical interface number
('ifIndex') assigned to this client, and is used to
identify corresponding rows in the Interfaces MIB.
Note that re-initialization of the management agent
may cause a client's 'lecIfIndex' to change. | ||||
| ClecPrimaryAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.2.1.2 | AtmLaneAddress | RO | |
column · AtmLaneAddress · read-only · current C1 LE Client's ATM Addresses. The primary ATM address of this LAN Emulation Client. This address is used to establish the Control Direct and Multicast Send VCCs, and may also be used to set up Data Direct VCCs. A client may have additional ATM addresses for use with Data Direct VCCs. These addresses are readable via the lecAtmAddressTable. | ||||
| ClecID | 1.3.6.1.4.1.353.5.3.1.1.2.1.3 | INTEGER (0..65279) | RO | |
column · INTEGER (0..65279) · read-only · current C14 LE Client Identifier. Each LE Client requires a
LE Client Identifier (LECID) assigned by the LE
Server during the Join phase. The LECID is placed
in control requests by the LE Client and MAY be
used for echo suppression on multicast data frames
sent by that LE Client. This value MUST NOT
change without terminating the LE Client and
returning to the Initial state. A valid LECID
MUST be in the range X'0001' through X'FEFF'.
The value of this object is only meaningful for a LEC
that is connected to a LES. For a LEC which does not
belong to an emulated LAN, the value of this object
is defined to be 0. | ||||
| ClecInterfaceState | 1.3.6.1.4.1.353.5.3.1.1.2.1.4 | LecState | RO | |
column · LecState · read-only · current The current state of the LAN Emulation Client. Note that 'ifOperStatus' is defined to be 'up' when, and only when, 'lecInterfaceState' is 'operational'. | ||||
| ClecLastFailureRespCode | 1.3.6.1.4.1.353.5.3.1.1.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Status code from the last failed Configure response or Join response. Failed responses are those for which the LE_CONFIGURE_RESPONSE / LE_JOIN_RESPONSE frame contains a non-zero code, or fails to arrive within a timeout period. If none of this client's requests have failed, this object has the value 'none'. If the failed response contained a STATUS code that is not defined in the LAN Emulation specification, this object has the value 'undefinedError'. The value 'timeout' is self-explanatory. Other failure codes correspond to those defined in the specification, although they may have different numeric values.
| ||||
| ClecLastFailureState | 1.3.6.1.4.1.353.5.3.1.1.2.1.6 | LecState | RO | |
column · LecState · read-only · current The state this client was in when it updated the 'lecLastFailureRespCode'. If 'lecLastFailureRespCode' is 'none', this object has the value initialState(1). | ||||
| ClecProtocol | 1.3.6.1.4.1.353.5.3.1.1.2.1.7 | INTEGER (1..255) | RO | |
column · INTEGER (1..255) · read-only · current The LAN Emulation protocol which this client supports, and specifies in its LE_JOIN_REQUESTs. | ||||
| ClecVersion | 1.3.6.1.4.1.353.5.3.1.1.2.1.8 | INTEGER (1..255) | RO | |
column · INTEGER (1..255) · read-only · current The LAN Emulation protocol version which this client supports, and specifies in its LE_JOIN_REQUESTs. | ||||
| ClecTopologyChange | 1.3.6.1.4.1.353.5.3.1.1.2.1.9 | TruthValue | RO | |
column · TruthValue · read-only · current C19 Topology Change. Boolean indication that the LE
Client is using the Forward Delay Time C18,
instead of the Aging Time C17, to age non-local
entries in its LE_ARP cache C16.
For a client which is not connected to the LES, this
object is defined to have the value 'false'. | ||||
| ClecConfigServerAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.2.1.10 | AtmLaneAddress | RO | |
column · AtmLaneAddress · read-only · current The ATM address of the LAN Emulation Configuration Server (if known) or the empty string (otherwise). | ||||
| ClecConfigSource | 1.3.6.1.4.1.353.5.3.1.1.2.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether this LAN Emulation Client used the LAN Emulation Configuration Server, and, if so, what method it used to establish the Configuration Direct VCC.
| ||||
| ClecActualLanType | 1.3.6.1.4.1.353.5.3.1.1.2.1.12 | LecDataFrameFormat | RO | |
column · LecDataFrameFormat · read-only · current C2 LAN Type.
The data frame format that this LAN Emulation Client
is using right now. This may come from
* lecConfigLanType,
* the LAN Emulation Configuration Server, or
* the LAN Emulation Server
This value is related to 'ifMtu' and 'ifType'. See
the LEC management specification for more details. | ||||
| ClecActualMaxDataFrameSize | 1.3.6.1.4.1.353.5.3.1.1.2.1.13 | LecDataFrameSize | RO | |
column · LecDataFrameSize · read-only · current C3 Maximum Data Frame Size.
The maximum data frame size that this LAN Emulation
client is using right now. This may come from
* lecConfigMaxDataFrameSize,
* the LAN Emulation Configuration Server, or
* the LAN Emulation Server | ||||
| ClecActualLanName | 1.3.6.1.4.1.353.5.3.1.1.2.1.14 | OCTET STRING (SIZE (0..32)) | RO | |
column · OCTET STRING (SIZE (0..32)) · read-only · current C5 ELAN Name.
The identity of the emulated LAN which this client
last joined, or wishes to join. This may come from
* lecConfigLanName,
* the LAN Emulation Configuration Server, or
* the LAN Emulation Server | ||||
| ClecActualLesAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.2.1.15 | AtmLaneAddress | RO | |
column · AtmLaneAddress · read-only · current C9 LE Server ATM Address. The LAN Emulation Server address currently in use or most recently attempted. If no LAN Emulation Server attachment has been tried, this object's value is the zero-length string. | ||||
| ClecProxyClient | 1.3.6.1.4.1.353.5.3.1.1.2.1.16 | TruthValue | RO | |
column · TruthValue · read-only · current C4 Proxy. Indicates whether this client is acting as a proxy. Proxy clients are allowed to represent unregistered MAC addresses, and receive copies of LE_ARP_REQUEST frames for such addresses. | ||||
| TlecMappingTable | 1.3.6.1.4.1.353.5.3.1.1.3 | NA | ||
table · not-accessible · current A table mapping the 'ifIndex' values of 'aflane8023' and 'aflane8025' interfaces to the 'lecIndex' values of the corresponding LAN Emulation Clients. | ||||
| RlecMappingEntry | 1.3.6.1.4.1.353.5.3.1.1.3.1 | NA | ||
| ClecMappingIndex | 1.3.6.1.4.1.353.5.3.1.1.3.1.1 | INTEGER (1..2147483647) | RO | |
column · INTEGER (1..2147483647) · read-only · current The 'lecIndex' of the client which implements the specified interface. | ||||
| TlecStatisticsTable | 1.3.6.1.4.1.353.5.3.1.1.4 | NA | ||
table · not-accessible · current An extension table containing traffic statistics for all the LAN Emulation Clients this host implements. | ||||
| RlecStatisticsEntry | 1.3.6.1.4.1.353.5.3.1.1.4.1 | NA | ||
row · not-accessible · current Each row in this table contains traffic statistics for one LAN Emulation client.
| ||||
| ClecArpRequestsOut | 1.3.6.1.4.1.353.5.3.1.1.4.1.1 | Counter32 | RO | |
column · Counter32 · read-only · current The number of LE_ARP_REQUESTs sent over the LUNI by this LAN Emulation Client. | ||||
| ClecArpRequestsIn | 1.3.6.1.4.1.353.5.3.1.1.4.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current The number of LE_ARP_REQUESTs received over the LUNI by this LAN Emulation Client. Requests may arrive on the Control Direct VCC or on the Control Distribute VCC, depending upon how the LES is implemented and the chances it has had for learning. This counter covers both VCCs. | ||||
| ClecArpRepliesOut | 1.3.6.1.4.1.353.5.3.1.1.4.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current The number of LE_ARP_RESPONSEs sent over the LUNI by this LAN Emulation Client. | ||||
| ClecArpRepliesIn | 1.3.6.1.4.1.353.5.3.1.1.4.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current The number of LE_ARP_RESPONSEs received over the LUNI by this LAN Emulation Client. This count includes all such replies, whether solicited or not. Replies may arrive on the Control Direct VCC or on the Control Distribute VCC, depending upon how the LES is implemented. This counter covers both VCCs. | ||||
| ClecControlFramesOut | 1.3.6.1.4.1.353.5.3.1.1.4.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current The total number of control packets sent by this LAN Emulation Client over the LUNI. | ||||
| ClecControlFramesIn | 1.3.6.1.4.1.353.5.3.1.1.4.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current The total number of control packets received by this LAN Emulation Client over the LUNI. | ||||
| ClecSvcFailures | 1.3.6.1.4.1.353.5.3.1.1.4.1.7 | Counter32 | RO | |
column · Counter32 · read-only · current The total number of * outgoing LAN Emulation SVCs which this client tried, but failed, to open; * incoming LAN Emulation SVCs which this client tried, but failed to establish; and * incoming LAN Emulation SVCs which this client rejected for protocol or security reasons. | ||||
| TlecServerVccTable | 1.3.6.1.4.1.353.5.3.1.1.5 | NA | ||
table · not-accessible · current A table identifying the Control and Multicast VCCs for each LAN Emulation Client this host implements. | ||||
| RlecServerVccEntry | 1.3.6.1.4.1.353.5.3.1.1.5.1 | NA | ||
row · not-accessible · current Each row in this table describes the Control VCCs and Multicast VCCs for one LAN Emulation client.
| ||||
| ClecConfigDirectInterface | 1.3.6.1.4.1.353.5.3.1.1.5.1.1 | LeConnectionInterface | RO | |
column · LeConnectionInterface · read-only · current The interface associated with the Configuration
Direct VCC. If no Configuration Direct VCC exists,
this object has the value 0. Otherwise, the objects
( lecConfigDirectInterface,
lecConfigDirectVpi, lecConfigDirectVci )
identify the circuit. | ||||
| ClecConfigDirectVpi | 1.3.6.1.4.1.353.5.3.1.1.5.1.2 | VpiInteger | RO | |
column · VpiInteger · read-only · current If the Configuration Direct VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecConfigDirectVci | 1.3.6.1.4.1.353.5.3.1.1.5.1.3 | VciInteger | RO | |
column · VciInteger · read-only · current If the Configuration Direct VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecControlDirectInterface | 1.3.6.1.4.1.353.5.3.1.1.5.1.4 | LeConnectionInterface | RO | |
column · LeConnectionInterface · read-only · current The interface associated with the Control Direct VCC.
If no Control Direct VCC exists, this object has the
value 0. Otherwise, the objects
( lecControlDirectInterface,
lecControlDirectVpi, lecControlDirectVci )
identify the circuit. | ||||
| ClecControlDirectVpi | 1.3.6.1.4.1.353.5.3.1.1.5.1.5 | VpiInteger | RO | |
column · VpiInteger · read-only · current If the Control Direct VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecControlDirectVci | 1.3.6.1.4.1.353.5.3.1.1.5.1.6 | VciInteger | RO | |
column · VciInteger · read-only · current If the Control Direct VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecControlDistributeInterface | 1.3.6.1.4.1.353.5.3.1.1.5.1.7 | LeConnectionInterface | RO | |
column · LeConnectionInterface · read-only · current The interface associated with the Control Distribute
VCC. If no Control Distribute VCC has been set up to
this client, this object has the value 0. Otherwise,
the objects
( lecControlDistributeInterface,
lecControlDistributeVpi,
lecControlDistributeVci )
identify the circuit. | ||||
| ClecControlDistributeVpi | 1.3.6.1.4.1.353.5.3.1.1.5.1.8 | VpiInteger | RO | |
column · VpiInteger · read-only · current If the Control Distribute VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecControlDistributeVci | 1.3.6.1.4.1.353.5.3.1.1.5.1.9 | VciInteger | RO | |
column · VciInteger · read-only · current If the Control Distribute VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object contains the value 0. | ||||
| ClecMulticastSendInterface | 1.3.6.1.4.1.353.5.3.1.1.5.1.10 | LeConnectionInterface | RO | |
column · LeConnectionInterface · read-only · current The interface associated with the Multicast Send
VCC. If no Multicast Send VCC exists, this object
has the value 0. Otherwise, the objects
( lecMulticastSendInterface,
lecMulticastSendVpi, lecMulticastSendVci )
identify the circuit. | ||||
| ClecMulticastSendVpi | 1.3.6.1.4.1.353.5.3.1.1.5.1.11 | VpiInteger | RO | |
column · VpiInteger · read-only · current If the Multicast Send VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecMulticastSendVci | 1.3.6.1.4.1.353.5.3.1.1.5.1.12 | VciInteger | RO | |
column · VciInteger · read-only · current If the Multicast Send VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecMulticastForwardInterface | 1.3.6.1.4.1.353.5.3.1.1.5.1.13 | LeConnectionInterface | RO | |
column · LeConnectionInterface · read-only · current The interface associated with the Multicast Forward
VCC. If no Multicast Forward VCC has been set up to
this client, this object has the value 0. Otherwise,
the objects
( lecMulticastForwardInterface,
lecMulticastForwardVpi,
lecMulticastForwardVci )
identify the circuit. | ||||
| ClecMulticastForwardVpi | 1.3.6.1.4.1.353.5.3.1.1.5.1.14 | VpiInteger | RO | |
column · VpiInteger · read-only · current If the Multicast Forward VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| ClecMulticastForwardVci | 1.3.6.1.4.1.353.5.3.1.1.5.1.15 | VciInteger | RO | |
column · VciInteger · read-only · current If the Multicast Forward VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0. | ||||
| TlecAtmAddressTable | 1.3.6.1.4.1.353.5.3.1.1.6 | NA | ||
table · not-accessible · current A table listing all of the ATM addresses belonging to this host's LAN Emulation Clients. | ||||
| RlecAtmAddressEntry | 1.3.6.1.4.1.353.5.3.1.1.6.1 | NA | ||
row · not-accessible · current Each row in this table describes one of a client's ATM addresses.
| ||||
| ClecAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.6.1.1 | AtmLaneAddress | NA | |
column · AtmLaneAddress · not-accessible · current The ATM address this row describes. This could be either a primary address or a secondary address. | ||||
| ClecAtmAddressStatus | 1.3.6.1.4.1.353.5.3.1.1.6.1.2 | RowStatus | RC | |
column · RowStatus · read-create · current Used to create and delete rows in this table. A management station may not change the status of a primary ATM address to 'notInService' or 'destroy' unless the client's ifAdminStatus is 'down', and the client's lecInterfaceState is 'initialState'. Secondary ATM addresses may be destroyed at any time permitted by the agent. | ||||
| TlecMacAddressTable | 1.3.6.1.4.1.353.5.3.1.1.7 | NA | ||
table · not-accessible · current This table contains entries for all of the registered
MAC addresses belonging to this agent's LE clients.
C6 Local Unicast MAC Address(es). Each LE Client has
zero or more local unicast MAC addresses. In an
operational LE Client, every address in this
variable MUST have been registered with the LE
Server. Two LE CLients joined to the same
emulated LAN MUST NOT have the same local unicast
MAC address. A LE Client's MAC addresses may
change during normal operations. When answering
a LE_ARP_REQUEST for any address in this list, the
'Remote Address' bit in the FLAGS field of the
LE_ARP_RESPONSE MUST be clear. | ||||
| RlecMacAddressEntry | 1.3.6.1.4.1.353.5.3.1.1.7.1 | NA | ||
row · not-accessible · current Each table row describes a (MAC address, ATM address) pair registered for a particular client.
| ||||
| ClecMacAddress | 1.3.6.1.4.1.353.5.3.1.1.7.1.1 | MacAddress | NA | |
column · MacAddress · not-accessible · current A unicast MAC address which the LE client denoted by 'lecIndex' has registered with its LE Server. | ||||
| ClecMacAddressAtmBinding | 1.3.6.1.4.1.353.5.3.1.1.7.1.2 | AtmLaneAddress | RO | |
column · AtmLaneAddress · read-only · current The ATM address registered for 'lecMacAddress'. | ||||
| TlecRouteDescrTable | 1.3.6.1.4.1.353.5.3.1.1.8 | NA | ||
table · not-accessible · current This table lists all of the Route Descriptors which
are registered by this host's LAN Emulation Clients.
C8 Route Descriptor(s). Route Descriptors exist only
for source-routed IEEE 802.5 LE Clients that are
Source-Route Bridges. All Route Descriptors in
any given emulated LAN MUST be unique. A LE
Client MAY have zero or more Route Descriptors
and these Route Descriptors MAY change during
normal operation. In an operational LE Client,
every Local Route Descriptor in C8 MUST have been
registered with the LE Server. When answering a
LE_ARP_REQUEST for any address in this list, the
'Remote Address' bit in the FLAGS field of the
LE_ARP_RESPONSE MUST be clear. | ||||
| RlecRouteDescrEntry | 1.3.6.1.4.1.353.5.3.1.1.8.1 | NA | ||
row · not-accessible · current Each table row describes a (Route Descriptor, ATM address) pair registered for a particular client. | ||||
| ClecRouteDescrSegmentID | 1.3.6.1.4.1.353.5.3.1.1.8.1.1 | INTEGER (0..4095) | NA | |
column · INTEGER (0..4095) · not-accessible · current The LAN ID portion of the IEEE 802.5 route descriptor associated with this conceptual row. | ||||
| ClecRouteDescrBridgeNumber | 1.3.6.1.4.1.353.5.3.1.1.8.1.2 | INTEGER (0..15) | NA | |
column · INTEGER (0..15) · not-accessible · current The Bridge Number portion of the IEEE 802.5 route descriptor associated with this conceptual row. | ||||
| ClecRouteDescrAtmBinding | 1.3.6.1.4.1.353.5.3.1.1.8.1.3 | AtmLaneAddress | RO | |
column · AtmLaneAddress · read-only · current The ATM address registered for the IEEE 802.5 route
descriptor ('lecRouteDescrSegmentID',
'lecRouteDescrBridgeNumber'). | ||||
| TleArpTable | 1.3.6.1.4.1.353.5.3.1.1.9 | NA | ||
table · not-accessible · current This table provides access to an ATM LAN Emulation
Client's MAC-to-ATM ARP cache. It contains entries
for unicast addresses and for the broadcast address,
but not for multicast MAC addresses.
C16 LE_ARP Cache. A table of entries, each of which
establishes a relationship between a LAN
Destination external to the LE Client and the
ATM address to which data frames for that LAN
Destination will be sent. | ||||
| RleArpEntry | 1.3.6.1.4.1.353.5.3.1.1.9.1 | NA | ||
row · not-accessible · current An ATM LAN Emulation ARP cache entry containing information about the binding of one MAC address to one ATM address.
| ||||
| CleArpMacAddress | 1.3.6.1.4.1.353.5.3.1.1.9.1.1 | MacAddress | NA | |
column · MacAddress · not-accessible · current The MAC address for which this cache entry provides a translation. Since ATM LAN Emulation uses an ARP protocol to locate the Broadcast and Unknown Server, the value of this object could be the broadcast MAC address. MAC addresses should be unique within any given ATM Emulated LAN. However, there's no requirement that they be unique across disjoint emulated LANs. | ||||
| CleArpAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.9.1.2 | AtmLaneAddress | RC | |
column · AtmLaneAddress · read-create · current The ATM address of the Broadcast & Unknown Server or LAN Emulation Client whose MAC address is stored in 'leArpMacAddress'. This value may be determined through the use of the LE_ARP procedure, through source address learning, or through other mechanisms. Some agents may provide write access to this object, as part of their support for 'static' LE_ARP entries. The effect of attempting to write an ATM address to a 'learned' row is explicitly undefined. Agents may disallow the write, accept the write and change the row's type, or even accept the write as-is. | ||||
| CleArpIsRemoteAddress | 1.3.6.1.4.1.353.5.3.1.1.9.1.3 | TruthValue | RO | |
column · TruthValue · read-only · current Indicates whether this entry is for a local or remote
MAC address.
In this context, 'local' means 'a MAC address that is
local to the remote client', as opposed to 'one of my
addresses'.
true(1)
The address is believed to be remote - or its
local/remote status is unknown.
For an entry created via the LE_ARP mechanism,
this corresponds to the 'Remote address' flag
being set in the LE_ARP_RESPONSE.
During Topology Change periods, remote LE_ARP
entries generally age out faster than others.
Specifically, they are subject to the Forward
Delay Time as well as to the Aging Time.
false(2)
The address is believed to be local - that is
to say, registered with the LES by the client
whose ATM address is leArpAtmAddress.
For an entry created via the LE_ARP mechanism,
this corresponds to the 'Remote address' flag
being cleared in the LE_ARP_RESPONSE. | ||||
| CleArpEntryType | 1.3.6.1.4.1.353.5.3.1.1.9.1.4 | LeArpTableEntryType | RC | |
column · LeArpTableEntryType · read-create · current Indicates how this LE_ARP table entry was created and whether it is aged. | ||||
| CleArpRowStatus | 1.3.6.1.4.1.353.5.3.1.1.9.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current Lets users create and delete LE_ARP cache entries,
on systems that support this capability.
Normally clients will maintain their LE_ARP caches
automatically. However, managers may occasionally
want to create 'static' LE_ARP cache entries.
Rules
1. Before a new row can become 'active', values
must be supplied for the columnar objects
leArpAtmAddress and leArpEntryType.
2. It is not necessary to set leArpRowStatus to
'notInService' in order to modify a writable
object in the same conceptual row.
3. LE_ARP entries whose status is 'notReady' or
'notInService' will not be used to translate
LAN Destinations to ATM Addresses. However,
clients may overwrite such entries with data
obtained from other sources. For example, a
client which needed to transmit a data frame
to a given MAC address (or via a given Route
Descriptor) might find that its LE_ARP entry
for the LAN Destination is 'notInService' or
'notReady'. The client might then act as if
the LAN Destination was unknown - generating
a LE_ARP_REQUEST, flooding the data frame to
the BUS, and creating a new, 'active' LE_ARP
cache entry based on the LE_ARP_RESPONSE. | ||||
| TleRDArpTable | 1.3.6.1.4.1.353.5.3.1.1.10 | NA | ||
table · not-accessible · current This table provides access to an ATM LAN Emulation
Client's Route Descriptor-to-ATM ARP cache.
Implementation of this table is optional for hosts
that do not support emulated IEEE 802.5 Token Ring
LANs, and mandatory for hosts which do.
C16 LE_ARP Cache. A table of entries, each of which
establishes a relationship between a LAN
Destination external to the LE Client and the
ATM address to which data frames for that LAN
Destination will be sent. | ||||
| RleRDArpEntry | 1.3.6.1.4.1.353.5.3.1.1.10.1 | NA | ||
row · not-accessible · current An ATM LAN Emulation ARP cache entry containing information about the binding of one IEEE 802.5 route descriptor to one ATM address. | ||||
| CleRDArpSegmentID | 1.3.6.1.4.1.353.5.3.1.1.10.1.1 | INTEGER (0..4095) | NA | |
column · INTEGER (0..4095) · not-accessible · current The LAN ID portion of the IEEE 802.5 route descriptor associated with this ARP cache entry. | ||||
| CleRDArpBridgeNumber | 1.3.6.1.4.1.353.5.3.1.1.10.1.2 | INTEGER (0..15) | NA | |
column · INTEGER (0..15) · not-accessible · current The Bridge Number portion of the IEEE 802.5 route descriptor associated with this ARP cache entry. | ||||
| CleRDArpAtmAddress | 1.3.6.1.4.1.353.5.3.1.1.10.1.3 | AtmLaneAddress | RC | |
column · AtmLaneAddress · read-create · current The ATM address of the LAN Emulation Client which is
associated with the route descriptor
('leRDArpSegmentID', 'leRDArpBridgeNumber').
This value may be determined through the use of the
LE_ARP procedure, through source address learning,
or through other mechanisms.
Some agents may provide write access to this object,
as part of their support for 'static' LE_ARP entries.
The effect of attempting to write an ATM address to
a 'learned' row is explicitly undefined. Agents may
disallow the write, accept the write and change the
row's type, or even accept the write as-is. | ||||
| CleRDArpEntryType | 1.3.6.1.4.1.353.5.3.1.1.10.1.4 | LeArpTableEntryType | RC | |
column · LeArpTableEntryType · read-create · current Indicates how this LE_ARP table entry was created and whether it is aged. | ||||
| CleRDArpRowStatus | 1.3.6.1.4.1.353.5.3.1.1.10.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current Lets users create and delete LE_ARP cache entries,
on systems that support this capability.
Normally clients will maintain their LE_ARP caches
automatically. However, managers may occasionally
want to create 'static' LE_ARP cache entries.
Rules
1. Before a new row can become 'active', values
must be supplied for the columnar objects
leRDArpAtmAddress and leRDArpEntryType.
2. It is not necessary to set leRDArpRowStatus to
'notInService' in order to modify a writable
object in the same conceptual row.
3. LE_ARP entries whose status is 'notReady' or
'notInService' will not be used to translate
LAN Destinations to ATM Addresses. However,
clients may overwrite such entries with data
obtained from other sources. For example, a
client which needed to transmit a data frame
to a given MAC address (or via a given Route
Descriptor) might find that its LE_ARP entry
for the LAN Destination is 'notInService' or
'notReady'. The client might then act as if
the LAN Destination was unknown - generating
a LE_ARP_REQUEST, flooding the data frame to
the BUS, and creating a new, 'active' LE_ARP
cache entry based on the LE_ARP_RESPONSE. | ||||
| NleClientMIBConformance | 1.3.6.1.4.1.353.5.3.1.2 | |||
| NleClientMIBGroups | 1.3.6.1.4.1.353.5.3.1.2.1 | |||
| GleClientConfigGroup | 1.3.6.1.4.1.353.5.3.1.2.1.1 | |||
group · current A collection of objects used for creating and configuring LAN Emulation Clients.
| ||||
| GleClientStatusGroup | 1.3.6.1.4.1.353.5.3.1.2.1.2 | |||
group · current A collection of objects describing the status and operational parameters of the managed LAN Emulation Clients.
| ||||
| GleClientMappingGroup | 1.3.6.1.4.1.353.5.3.1.2.1.3 | |||
group · current A collection of objects which map a LAN Emulation Client's 'ifIndex' to its 'lecIndex'.
| ||||
| GleClientStatisticsGroup | 1.3.6.1.4.1.353.5.3.1.2.1.4 | |||
group · current A collection of objects which act as an extension to the lecConfigTable. These objects provide statistics on LAN Emulation control traffic and SVC establishment. | ||||
| GleClientServerVccGroup | 1.3.6.1.4.1.353.5.3.1.2.1.5 | |||
group · current A collection of objects which act as an extension to the lecConfigTable. These objects identify Configuration Direct, Control, and Multicast VCCs for each client, making it easier to locate their entries in the AToM MIB.
| ||||
| GleClientAtmAddressesGroup | 1.3.6.1.4.1.353.5.3.1.2.1.6 | |||
group · current A collection of objects which describe all of the ATM addresses belonging to each client.
| ||||
| GleClientMacAddressesGroup | 1.3.6.1.4.1.353.5.3.1.2.1.7 | |||
group · current A collection of objects which describe all of the MAC addresses registered for each client.
| ||||
| GleClientRouteDescriptorsGroup | 1.3.6.1.4.1.353.5.3.1.2.1.8 | |||
group · current A collection of objects which describe all of the Route Descriptors registered for each client.
| ||||
| GleClientArpGroup | 1.3.6.1.4.1.353.5.3.1.2.1.9 | |||
group · current A collection of objects which describe the MAC- to-ATM address mappings that this LAN Emulation Client has learned. | ||||
| GleClientRDArpGroup | 1.3.6.1.4.1.353.5.3.1.2.1.10 | |||
group · current A collection of objects which describe the IEEE 802.5 Route Descriptor-to-ATM address mappings that this LAN Emulation Client has learned. | ||||
| NleClientMIBCompliances | 1.3.6.1.4.1.353.5.3.1.2.2 | |||
| MleClientMIBCompliance | 1.3.6.1.4.1.353.5.3.1.2.2.1 | |||
compliance · current The compliance statement for SNMP entities
which support ATM LAN Emulation Clients.
For a host to conform to this MIB, it must also implement
- RFC 1213 - MIB II.
- Interfaces table entries for each LE Client, as per the
LAN Emulation Client management specification.
- The AToM MIB (RFC 1695 - Definitions of Managed Objects
for ATM Management), according to the conformance
statements defined in that RFC.
Optionally, a host may implement
- RFC 1573 - Evolution of the Interfaces Group of MIB-II.
- The 'ifRcvAddressGroup' from RFC 1573, which provides a
way to represent and configure interfaces with multiple
addresses.
See the LAN Emulation Client management specification for
interpretations of RFC 1573 / MIB-II as they apply to LAN
Emulation Clients. | ||||
Textual conventions
AtmLaneAddressOCTET STRING (SIZE (0 | 20))A twenty-octet binary string, containing a standard ATM Forum address -- or the zero-length string, indicating the absence of an address. For LAN Emulation purposes, the eight-octet address format is not used.
LeArpTableEntryTypeINTEGERlearnedViaControl(2)learnedViaData(3)other(1)staticNonVolatile(5)staticVolatile(4)Indicates how a LE_ARP table entry was created and whether it is subject to aging. other(1) The LE_ARP entry does not fall into one of the categories defined below. learnedViaControl(2) This LE_ARP entry was learned by using the LE_ARP_REQUEST / LE_ARP_RESPONSE protocol, or by otherwise observing relevant traffic on Control VCCs. Entries of this type are aged. learnedViaData(3) This LE_ARP entry was learned by observing incoming traffic on Data VCCs. Entries of this type are aged. staticVolatile(4) This LE_ARP entry was created by management. It will not be aged. On the other hand, it will not survive a restart of the client. If an agent permits LE_ARP entries of this type to be created, it may require that the LAN Emulation Client be in the 'operational' state at the time. staticNonVolatile(5) This LE_ARP entry was created by management. It will not be aged, and it will survive a restart of the client. The values 'learnedViaData' and 'learnedViaControl' can be read, but may not be written.LeConnectionInterfaceINTEGER (0..2147483647)A combination flag and ifTable index, indicating whether a LAN Emulation circuit exists - and, if so, which interface is associated with it at the point where it connects to a LE Client. Objects of this type are always defined as part of a set that includes fooInterface LeConnectionInterface fooVpi VpiInteger fooVci VciInteger The interpretation of these objects is as follows. 1. If no connection exists, 'fooInterface' has a value of 0. Because Interfaces table entries always have 'ifIndex' values larger than 0, 'fooInterface' reliably serves as a 'connection exists' flag. In this case, 'fooVpi' and 'fooVci' are meaningless, and have the value 0. 2. If a PVC or SVC exists, 'fooInterface' is defined to have the value of the MIB-II/RFC 1573 'ifIndex' of the 'atm' interface associated with the VCC. 'fooVpi' and 'fooVci' will contain its VPI/VCI. Therefore, ('fooInterface', 'fooVpi', 'fooVci') give you an index into the AToM MIB which allows you to examine and play with the circuit further. 3. If a proprietary connection (such as an internal data path between co-located components) exists, this specification does not mandate how it should be managed. One option is to set 'fooInterface' to the value of the MIB-II/RFC 1573 'ifIndex' for the LAN Emulation Client. This indicates that a connection exists, but is not being managed in the same fashion as an ATM VCC.LecDataFrameFormatINTEGERaflane8023(2)aflane8025(3)unspecified(1)A 'LAN Type' value. C2 LAN Type. The type of LAN that the LE Client is, or wishes to become, a member of. This MUST be one of Ethernet/IEEE 802.3, IEEE 802.5, or Unspecified.LecDataFrameSizeINTEGERmax1516(2)max18190(5)max4544(3)max9234(4)unspecified(1)A 'Maximum Data Frame Size' value. C3 Maximum Data Frame Size. The maximum AAL-5 SDU size of a data frame that the LE Client wishes to send on the Multicast Send VCC or to receive on the Multicast Send VCC or Multicast Forward VCC. This parameter also specifies the maximum AAL-5 SDU on all of a LE Client's Data Direct VCCs. This MUST be either 1516, 4544, 9234, or 18190 octets, or Unspecified.LecStateINTEGERbusConnect(6)configure(3)initialRegistration(5)initialState(1)join(4)lecsConnect(2)operational(7)An official protocol state of a LAN Emulation Client.
VciIntegerINTEGER (0..65535)An integer large enough to hold a VCI.
VpiIntegerINTEGER (0..255)An integer large enough to hold a VPI.